Member Since: 06 Jan 2005
Location: Norway
Posts: 56
WDS 13 Patch 1 Update removes the Pre Heater and Pre Cooler
I got my Disco 3 updated to software version 13 and:
IT removed the PreHeater and the Pre Cooler function!
Has I used these radio trick I`m demanding it reinstalled or LR has to
pay for an Webesto programmer!
I use the preheater function everyday, since it`s about -15C in Norway.
It also added an i with a arrow pointing to the right in the infocenter!
Finally my aircondition press heat on the top wents not just on my feet!
PerS 8)
13th Feb 2006 7:49 am
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26779
The question on everybodys lips is has it improved the overall reliability of the software! Whilst the pre-heater has been a hot potato (pardon pun), the more general trend for cars to be laid up with silly electronic bugs and glitches has been more of an issue and concern to more recent aquirers of Discovery 3.
It will be good to hear that it improved things in other areas, but the pre-heater issue will ruffle some feathers I'm sure.
I have not used the pre-heater for some time now, I got a new coat instead . It does make me realise that in the UK at least, it is not as big an issue as it first appeared to be.
13th Feb 2006 8:58 am
Winger Site Moderator
Member Since: 15 Feb 2005
Location: UK
Posts: 3428
WDS 13 Patch 1 does provide Discovery 3 revised Instrument Pack Software - which does change to settings menu as described above.
Be aware of this if you like the pre-heat/cool settings hack, and don't want to lose it.
13th Feb 2006 10:09 am
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26779
Is that all it does to the instrument pack, or are their other mods too?
13th Feb 2006 11:27 am
irf
Member Since: 28 Sep 2005
Location: Herts
Posts: 106
Re: WDS 13 Patch 1 Update removes the Pre Heater and Pre Coo
pers1 wrote:
It also added an i with a arrow pointing to the right in the infocenter!
PerS 8)
On my 06 HSE an i appearing in the infocentre means that something needs attention.
Push the LH stalk to get a message describing the problem. In my case it was a reminder that the washer bottle needed topping up.
Top up the bottle and no i
Are you saying that the i is on all the time with no purpose ?
13th Feb 2006 12:31 pm
Winger Site Moderator
Member Since: 15 Feb 2005
Location: UK
Posts: 3428
Older software version did not throw up the "i" - the update deals with that, and it sounds like your probably have that version already installed in your car.
13th Feb 2006 12:39 pm
simon
Member Since: 11 Jan 2005
Location: Shropshire
Posts: 18296
mines in today for some minor niggle stuff so software is supposed to be updated. Not worried about the pre heat / cool timer at all - car warms up plenty fast for me and the heated seats are a bonus.
-s
13th Feb 2006 1:06 pm
SN
Member Since: 03 Jan 2006
Location: Romiley
Posts: 13710
Re: WDS 13 Patch 1 Update removes the Pre Heater and Pre Coo
irf wrote:
On my 06 HSE an i appearing in the infocentre means that something needs attention.
Push the LH stalk to get a message describing the problem. In my case it was a reminder that the washer bottle needed topping up.
Top up the bottle and no i
Are you saying that the i is on all the time with no purpose ?
Thanks for that! I had an 'i' last time I lookedSteve N | 21MY Defender | 08MY Discovery 3 (history) | 06MY Discovery 3 (ancient history)
13th Feb 2006 1:29 pm
aitchy
Member Since: 27 Sep 2005
Location: Peterborough
Posts: 130
i had s/w 13 loaded on my 06 HSE to fix heater issues and since then i have had 3 instances of transmission/park brake/gear selector issues when cold (-2) at stat up resolved by stop/start routine. its back in today for the repalcement steering column link (to remove knocking) and for a review of this s/w given that i have now found the suspension fault reference in another thread which i have passed on to my dealer...oh by the way, i got a D3 SE loaner for the day FOC so no complaints there.TDV6 HSE Buckingham Blue and still smiling
14th Feb 2006 12:06 pm
davide
Member Since: 04 Feb 2006
Location: desio
Posts: 1
Guys
I'm writing from Italy. There is a solution the patch that remove the pre heater webasto. In fact is possible to install the sw 13, and with the agreement of the land rover seller to use the sw that they have and active again the function. The problem is that the sellers have not the code number to enter in the engineering function. If there is this code, is possible to load sw 13, to attach the pc for the diagnostic control, enter in the engineering mode, code and re-active the webasto. Unfortunately I have not this code. If someone find it, I can test! bye davide
16th Feb 2006 7:52 am
simon
Member Since: 11 Jan 2005
Location: Shropshire
Posts: 18296
Getting confirmation on Friday of what disk was used on my car WDS 13 or WDS 13 patch 1. Also which updates were uploaded. Dealer usually does all of them as a matter of course.
I still have the Pre Heat / Cool menu.
I have noticed the engine is far smoother - especially 1st to 2nd changes with no drop off of revs like before. Am still assessing this and will be in stop start traffic today... should be far smoother with luck.
Heater seems to be more efficient.
Keep you posted
-s
16th Feb 2006 8:44 am
AndrewS Tarquin of the Desert
Member Since: 06 May 2005
Location: Y...... because I can
Posts: 10442
Just got my car back from having a 45,000 mile service. It has had the latest software installed. The auto gearbox now changes up before I feel it should, I presume that the memory in the box has been wiped and it will adapt to my style of driving again in time. Also the steering seems heaver at slow speeds. I will check on the points above later today to see what else has been done.In the Beginning there was nothing, which exploded.
16th Feb 2006 9:07 am
lee01277
Member Since: 06 May 2005
Location: Shed
Posts: 821
ref heavy steering .. did you check the tyre pressures after the service ?..............Somewhere in-between my old D3 and what's to come next .........
16th Feb 2006 9:12 am
AndrewS Tarquin of the Desert
Member Since: 06 May 2005
Location: Y...... because I can
Posts: 10442
oh yea In the Beginning there was nothing, which exploded.
16th Feb 2006 9:40 am
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18573
davide wrote:
Guys
I'm writing from Italy. There is a solution the patch that remove the pre heater webasto. In fact is possible to install the sw 13, and with the agreement of the land rover seller to use the sw that they have and active again the function. The problem is that the sellers have not the code number to enter in the engineering function. If there is this code, is possible to load sw 13, to attach the pc for the diagnostic control, enter in the engineering mode, code and re-active the webasto. Unfortunately I have not this code. If someone find it, I can test! bye davide
Hi Davide - thanks for the information and welcome to DISCO3 06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
. It does make me realise that in the UK at least, it is not as big an issue as it first appeared to be.
| 08MY Discovery 3 (history) 
oh yea 
