Member Since: 13 Oct 2014
Location: Nottingham
Posts: 1782
Read up on Robbie's guide for fitting Prospeed ones, the principles the same. I highly recommend a spray with dinitrol and liberal use of copper grease in the threaded holes. Doesn't really matter about the yellow studs, though as you say, just snipping the pip off wil leave the hole sealed.
I have a 1mm thick x 25mm wide self adhesive rubber strip on mine, top and side, just to stop some of the mud etc getting behind it.There are two rules for success,
1. Never tell everything you know.
D4 gone!
D5
15th Jun 2016 6:27 pm
alski
Member Since: 20 Oct 2009
Location: Belfast
Posts: 145
MarkOne wrote:
Get them fitted and get some pictures posted, Alski and i will be getting our's just not the now.
Hi Mark
All going well they should be collected this weekend
Should be here soon after that.
15th Jun 2016 9:29 pm
MarkOne
Member Since: 23 Jul 2011
Location: County Antrim
Posts: 3345
Fine Al thanks, sooner than you might have thought then
16th Jun 2016 5:46 am
Madrilleno
Member Since: 13 Oct 2014
Location: Nottingham
Posts: 1782
IMPORTANT - with these tree sliders you do NOT remove the rubber trim from the bottom of the door.
Member Since: 21 Nov 2013
Location: Binfield
Posts: 37
Ok chaps, what am I doing wrong, none of the bolts on the underside of the sill will go in more than a couple of mm?
16th Jun 2016 10:23 am
Madrilleno
Member Since: 13 Oct 2014
Location: Nottingham
Posts: 1782
Without the slider in place?There are two rules for success,
1. Never tell everything you know.
D4 gone!
D5
16th Jun 2016 10:30 am
Cantthinkofone
Member Since: 21 Nov 2013
Location: Binfield
Posts: 37
No, with the slider in place but the slider is not fouling the bolts so would be the same without it there I think
16th Jun 2016 10:32 am
Scott-tdv6
Member Since: 22 Oct 2014
Location: Stonehaven,Aberdeenshire
Posts: 45
Probably full of muck? Loads of wd40 and work the bolt back and forth not to forcefully may clean it out, or run a tap through first maybe
16th Jun 2016 10:35 am
Madrilleno
Member Since: 13 Oct 2014
Location: Nottingham
Posts: 1782
Cleaned out the thread?
Tried a bolt which you know will fit in one of the other holes?There are two rules for success,
1. Never tell everything you know.
D4 gone!
D5
16th Jun 2016 10:35 am
Cantthinkofone
Member Since: 21 Nov 2013
Location: Binfield
Posts: 37
Will try the wd40 and a gold old clean, the bolts fit on the side no problem
16th Jun 2016 10:45 am
Cantthinkofone
Member Since: 21 Nov 2013
Location: Binfield
Posts: 37
Thanks chaps, all done, well the drivers side is done anyway, with a few lessons learned for when I tackle the passenger side. One hole was particularly bad but a good hose, wd40, tissue, wiggle with a screwdriver and about 30 ins and outs with the bolt and it was just about in. Let's hope all the rocks are on the drivers side on the school run today!
16th Jun 2016 12:33 pm
Madrilleno
Member Since: 13 Oct 2014
Location: Nottingham
Posts: 1782
There are two rules for success,
1. Never tell everything you know.
D4 gone!
D5
16th Jun 2016 12:44 pm
Scott-tdv6
Member Since: 22 Oct 2014
Location: Stonehaven,Aberdeenshire
Posts: 45
My sliders are now fitted, very happy with them,
Definitely reccommend running a tap through the holes before offering up the slider, takes 10 mins extra but makes it so much easier!
Will put a pic up later
16th Jun 2016 4:33 pm
Joes
Member Since: 05 Sep 2015
Location: Limburg
Posts: 16
The tree sliders have made it to Belgium.
Could not wait to test fit one this evening.
+1 on using a tap for the holes.
Also, for the ones who have been offroad, with the platic sills removed, also remove the rubber grommets (temporary) and give your sills internals a good flush with the water hose.
I will be dinitrolling the out and inside of the sills this weekend
16th Jun 2016 8:37 pm
Scott-tdv6
Member Since: 22 Oct 2014
Location: Stonehaven,Aberdeenshire
Posts: 45
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum