have not received anything yet
How did You send it ?
have You any Tracking details ?
Regards
Jan R.Jan R.
______________________________
LR Disco3 TDV6 HSE 2005 Cairns Blue
Club BAS-FBHIC+Club BAS-Remap
Hidden Winch Mount ( Warn / Tabor 9K ) with Synthetic Line.
A-Frame Protection Bar with Lightforce 170 Xenon
Mantec Raised Air Intake LR Expo Rack OzTent Batwing,+ Frontrunner
GNVP-Suspension Rods+Rock Slider/Step+Full Underbody Protection
GG AT2s 255/60/18
Ham Radio ( HF-UHF ) Blackvue DR590X-2CH HD Camera
Squishy Cup Holders, Engel MT-35 Fridge, Cubby Fridge
GAP IIDtool BT
14th Oct 2015 11:29 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
Its on its way Jan, I'll PM you tracking details shortly My D3 Build Thread
Regards
Jan R.Jan R.
______________________________
LR Disco3 TDV6 HSE 2005 Cairns Blue
Club BAS-FBHIC+Club BAS-Remap
Hidden Winch Mount ( Warn / Tabor 9K ) with Synthetic Line.
A-Frame Protection Bar with Lightforce 170 Xenon
Mantec Raised Air Intake LR Expo Rack OzTent Batwing,+ Frontrunner
GNVP-Suspension Rods+Rock Slider/Step+Full Underbody Protection
GG AT2s 255/60/18
Ham Radio ( HF-UHF ) Blackvue DR590X-2CH HD Camera
Squishy Cup Holders, Engel MT-35 Fridge, Cubby Fridge
GAP IIDtool BT
LR Disco3 TDV6 HSE 2005 Cairns Blue
Club BAS-FBHIC+Club BAS-Remap
Hidden Winch Mount ( Warn / Tabor 9K ) with Synthetic Line.
A-Frame Protection Bar with Lightforce 170 Xenon
Mantec Raised Air Intake LR Expo Rack OzTent Batwing,+ Frontrunner
GNVP-Suspension Rods+Rock Slider/Step+Full Underbody Protection
GG AT2s 255/60/18
Ham Radio ( HF-UHF ) Blackvue DR590X-2CH HD Camera
Squishy Cup Holders, Engel MT-35 Fridge, Cubby Fridge
GAP IIDtool BT
Still waiting for Your response about Shipping / Tracking details.
Regards
Jan R.Jan R.
______________________________
LR Disco3 TDV6 HSE 2005 Cairns Blue
Club BAS-FBHIC+Club BAS-Remap
Hidden Winch Mount ( Warn / Tabor 9K ) with Synthetic Line.
A-Frame Protection Bar with Lightforce 170 Xenon
Mantec Raised Air Intake LR Expo Rack OzTent Batwing,+ Frontrunner
GNVP-Suspension Rods+Rock Slider/Step+Full Underbody Protection
GG AT2s 255/60/18
Ham Radio ( HF-UHF ) Blackvue DR590X-2CH HD Camera
Squishy Cup Holders, Engel MT-35 Fridge, Cubby Fridge
GAP IIDtool BT
17th Oct 2015 11:30 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
I have just set my gap tool up to the car and downloaded new firmware. I then thought I would have a little play with it and add a few things when I had changed them and clicked upload it would not do it as it said battery voltage was too low. So I disconnected it and thought I would start engine to charge it but it just clicked and will not start as battery is flat. Do these things take a lot of charge when working as ignition is on and quite a lot of things are running ? It was in that mode for about 20 mins. when I first connected it I remember it saying battery 12.2 volt. Is this normal or is battery knackered ? I have not had any trouble before.
17th Oct 2015 1:20 pm
tayaste
Member Since: 15 May 2013
Location: Chester
Posts: 7633
Normal, it's good practice to hook up a supply or to a second vehicle. With the ignition left on with no supply the vehicle is using a lot of amps
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum