Member Since: 22 May 2019
Location: Norfolk
Posts: 305
C1A13-64 air suspension question
So have the above intermittent fault (pressure doesn’t decrease when venting gallery) on my 2010 disco 4 122k had a search around for fixes and think I know what I need to fix it.....however can any one confirm what I need and what compressor I have?
I think it’s hitachi and i need LR075760 to fix it or maybe LR030590 or should I just get the complete compressor??
This the compressor-
28th Sep 2019 7:35 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
It’s hitachi so guessing it’s original, used LR020590 as the ‘fix’ so far so good.....
3rd Oct 2019 8:14 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Faults back, had the below errors at or around the same time, anyone got any ideas?
6th Oct 2019 7:25 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6403
for C1A13-64 possible causes -
ehaust valve stuck closed
gallery pipe blocked / damaged /crushed
air susp exhaust silencer blocked / restricted
7th Oct 2019 6:33 am
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Cheers grzesiu
I’ll have a look and see where they are, and if I can spot anything
7th Oct 2019 1:57 pm
Littlewill
Member Since: 14 Sep 2015
Location: Lincolnshire
Posts: 484
A couple of posts with this fault in the past few days. Please post the fix if you find it!
7th Oct 2019 2:13 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Will do, if I find it!
7th Oct 2019 5:05 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14136
Also pull out the 2 x pipes that go into the end of the dryer , one is for the compressors air intake the other onto the exhaust silencer
After removing them see if the fault goes away , as at least then u can eliminate them with a simple 10 x minute test
The silencer looks like a large canister that sits by the back passenger side wheel
Also enclosed a pic of the silencer as I bought one at the same time when I fitted a new air tank
7th Oct 2019 5:23 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Very helpful I’ll report back what I find
7th Oct 2019 9:12 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Thought I was getting somewhere......had the fault every time I tried to lower the suspension then it went away again, had look round nothing obvious, I’ll overhaul the compressor I thought...... all went well suspension was a little slow to rise but no errors......now this morning when driving
bong normal height only and an error with the air supply, compressor appears to be building pressure as there’s air coming out to the valve, gallery pressure also rose to 1300 ish before it cut out error free, I’ve tried testing the valves on the iId but again no use if anything it’s worse as it’s now on the bump stops, now off to the compressor off and see if I can spot anything, any other suggestions???
12th Oct 2019 11:18 am
DiscoJeffster
Member Since: 27 Feb 2016
Location: Perth
Posts: 204
I'll save you some time.
When the air compressor exhales it does it back through the desiccant/filter. If you open yours up you'll find it's probably turned to dust and the filters are blocked. This means it's struggling to lose air at the rate it should. I just fixed the exact problem the other day.
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Sorry forgot to mention I’ve done the refurb......wasn’t to bad inside to be fair I’ve had the new fault since
Turns out my exhaust valve is stuck open, couldn’t hear it on the truck but as I’d cut the pipe when removing the compressor (as the fitting was seized) I pulled the coupler apart and could hear the air escaping, as a note I couldn’t replicate this on the bench guess I couldn’t get the same resistance as the system produces, guess I now need the solenoid? On the bench it appears to work tho as I can see movement not sure if the pressure pushing against it has weakened it over the years? Am wondering if there’s a control relay at fault somewhere? Off to search some more!!!!
12th Oct 2019 6:36 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Anyone ever managed to track down a replacement solenoid? Or know if it’s possible to refurb it?
13th Oct 2019 12:22 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Replaced the hitachi compressor and all is well, have spoken to where I bought the refurb kit from and explained their kit didn’t contain everything to fix the errors listed they are sending a ‘second hand test solenoid’
16th Oct 2019 7:19 pm
Andyyav
Member Since: 22 May 2019
Location: Norfolk
Posts: 305
Last update from me on this one! To recap I had the pressure doesn’t decrease when venting gallery error, used the refurb kit of filters, desiccant, piston ‘ring’ etc but then couldn’t build any pressure as the exhaust valve solenoid wasn’t holding, ordered and fitted a new hitachi compressor all is good, messaged the refurb kit chaps to say it didn’t cover the exhaust valve and they sent a second hand one (they don’t sell new ones) fitted it to my old compressor and it worked fine, so I now have a spare compressor! I pulled the old solenoid apart coil resistance is the same as the replacement one, played with the spring and it worked for a bit so guess it’s lost some strength pictures below,
Cheers for all the advice with this one!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
compressor appears to be building pressure as there’s air coming out to the valve, gallery pressure also rose to 1300 ish before it cut out error free, I’ve tried testing the valves on the iId but again no use if anything it’s worse as it’s now on the bump stops, now off to the compressor off and see if I can spot anything, any other suggestions???
