Mine passed it's MOT this week with the only comment(advisory?) being that the underside was lightly corroded. However, before it went in for MOT it had 2 new front lower control arms, new ARB drop links front and rear, replaced all brake calipers and pads and replaced flexible brake pipes for stainless steel. It's V8 2005 model imported from Australia with 258,000 KM's on the clock.
Need to replace upper dash top as the existing one is very cracked due to Queensland sun.
Member Since: 15 Aug 2017
Location: Milton Keynes
Posts: 1071
Took it to have new compressor fitted ouch good new all ready for a week away in the caravan First holiday away with two dogs one 10 years and other 11 months only will have been with us for two weeks but progressing well Welsh Collie Chauffeur Service To Barney & Rooney.
18th Mar 2020 4:45 pm
Hot Tub
Member Since: 15 Aug 2017
Location: Milton Keynes
Posts: 1071
Fitted a dog guard boot space divider so Barney & Rooney can travel together but separate
Now thinking of how to modify the Xanadoo basket so that can be used as well. Thinking of cutting it in half put angle on either side of the center divider so it still can be slide backwards and forwards
Open to suggestion what might be better
Not sell it to me ones before anyone ask Welsh Collie Chauffeur Service To Barney & Rooney.
19th Mar 2020 7:10 pm
sparkysteve
Member Since: 08 Jul 2017
Location: cheshire
Posts: 126
over the last few days been busy,
4 new rear parking sensors fitted
cleaned off rust from back end and repainted
plus a little trip to A&E after been attacked by the bumper
2" cut after tripped and stood on the bumper, which flipped up and did the deedD3 HSE 2.7 TDV6 named Calvin with him stuffed Tiger Hobbes sat in the back
27th Apr 2020 3:06 pm
lard
Member Since: 07 Jul 2018
Location: Wiltshire
Posts: 143
ouch! Hopefully didn't damage the bumper! (seriously though hope the head is ok!)
What was the paint process as something I need to clean up on mine... scrape off the surface rust with a brush... paint with the red stuff (rust inhibitor?) and them coat with black (assume it's a generic paint?)
Thanks!
27th Apr 2020 4:26 pm
sparkysteve
Member Since: 08 Jul 2017
Location: cheshire
Posts: 126
Used a wire brush thing on my angle grinder and a dremel for the hard to reach area's,
Cleaned off the loose rust and bits off,
Used red oxide primer two coats
Then sprayed satin black.
Hopefully will slow the rusting process
And thanks I'm ok now, got glued in A&ED3 HSE 2.7 TDV6 named Calvin with him stuffed Tiger Hobbes sat in the back
27th Apr 2020 6:13 pm
Shane1000rr
Member Since: 04 Jan 2020
Location: County Durham
Posts: 97
Treated my chassis to a full clean down and treatment
3rd May 2020 7:20 pm
Discoed
Member Since: 16 Jun 2010
Location: Yorkshire
Posts: 1020
Sump guard
Today I have fitted the sump guard purchased from the FS section -
oops wrong sectionD4 2014
1965 Land Rover series 2A (200Tdi)
5th May 2020 4:59 pm
Hormic23
Member Since: 14 Aug 2017
Location: Hampshire
Posts: 99
At 13 years of age I thought it was about time for a little clean in the engine bay
Member Since: 02 Nov 2016
Location: Surrey
Posts: 1046
Looks good, what did you use to get it so clean?Just 'cause you got the power... that don't mean you got the right.
17th May 2020 6:22 pm
Hormic23
Member Since: 14 Aug 2017
Location: Hampshire
Posts: 99
Thanks Firstly I took all the bits out and didn’t clean anything in situ, so I removed the air intake/air filter box, fan cover, battery cover and the spare battery box cover. Once the items were out the sequence was jet wash, spray with autobrite citrus cleaner (diluted to about 20/1) and agitate with sponge, jet wash off, dry, then 303 aerospace protectant and then micro fibre off.2007 D3 TDV6 XS - GONE
BAS Remap
EGRs blanked
Adaptive bi-xenons
RLD spare wheel protector
17th May 2020 7:26 pm
pjm-84
Member Since: 04 Oct 2016
Location: Hampshire
Posts: 2579
Rear air valve block. PITA. Thanks for Gary's tip with the push-fit fittings. An hour to get off. 5mins to put back on.
17th May 2020 8:20 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4508
Grille swap
Before
After
Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
17th May 2020 8:37 pm
ClassikFan
Member Since: 02 Nov 2016
Location: Surrey
Posts: 1046
Hormic23 wrote:
Thanks Firstly I took all the bits out and didn’t clean anything in situ, so I removed the air intake/air filter box, fan cover, battery cover and the spare battery box cover. Once the items were out the sequence was jet wash, spray with autobrite citrus cleaner (diluted to about 20/1) and agitate with sponge, jet wash off, dry, then 303 aerospace protectant and then micro fibre off.
I've always tried to clean under the bonnet with all the covers in situ. Never thought to take them off and give a good blast with the pressure washer.Just 'cause you got the power... that don't mean you got the right.
18th May 2020 6:30 pm
Hormic23
Member Since: 14 Aug 2017
Location: Hampshire
Posts: 99
Took a stop off at Royal steering wheels in Aylesbury for a re-trim. Very happy with the results and the good service - the old shiny, melted leather look Is no more
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
good new all ready for a week away in the caravan 
First holiday away with two dogs one 10 years and other 11 months only will have been with us for two weeks but progressing well 
(seriously though hope the head is ok!)
