Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Engine cut out
Good morning, just got in after being recovered home, driving along when engine light came on followed by a message critical engine fault then engine cut off, scanned and had P250A & P0195 codes.
Car will turn over but will not fire. ?
Recovery man checked fuel line nipple, wet but no squirt of fuel.
Any advice appreciated
24th Mar 2024 2:51 am
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Update, so had car scanned again and looks like a fuel pressure issue, actual pressure on cranking starts at approximately 32 psi going up to around 55 psi ish, car looking for 233. Psi If I remember correctly.
Any advice appreciated.
24th Mar 2024 12:43 pm
Fireburst
Member Since: 02 Nov 2017
Location: Hertfordshire
Posts: 195
Check Robbies guide to low pressure fuel pump, I think you will find the pressure at the schrader valve is much lower than you mention.
I thought I had a fuel pressure issue recently when my engine cut out while I was driving, it turned out to be the Crank shaft position sensor. Car has been running fine since the sensor was changed.
25th Mar 2024 9:57 am
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
This is just the kind of info I need, thank you.
I’m slowly reading threads and applying to the car when time permits.
The crank position sensor was changed under the recall about 3 months ago, Barrettes Ashford.
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Hay no worries, all help welcome
25th Mar 2024 9:03 pm
Browny90
Member Since: 19 Jul 2016
Location: Ashbourne
Posts: 698
Hello mate, How are you getting on?
Just curious
I assume something like the position sensor or the FP belt snapped? Although I don't think it's common, still possible..Disco4 MY16 SDV6 Landmark Black
Disco4 MY12 SDV6 XS Orkney Grey (Gone)
Defender 90 200tdi Completely rebuilt.
26th Mar 2024 9:33 am
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Hi, no further on.Between work and family not had time.
Will keep forum updated though.
26th Mar 2024 10:15 pm
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
So, checked for crank movement from under the vehicle after removing guards and cooler thingy.
No movement.
Checked lpfp, running and pulling 7 amps. I’ve not got a gauge to fit the test pointin the engine bay.
29th Mar 2024 3:54 pm
Browny90
Member Since: 19 Jul 2016
Location: Ashbourne
Posts: 698
I think you need to check the HPFP belt..
It certainly seems like you e snapped the belt..
It’s not an impossible job with the body on, just awkward.. but you only need to get as far as taking the cover off to check to start with..Disco4 MY16 SDV6 Landmark Black
Disco4 MY12 SDV6 XS Orkney Grey (Gone)
Defender 90 200tdi Completely rebuilt.
29th Mar 2024 4:48 pm
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Yes, that’s my next port of call.
Will update soon.
30th Mar 2024 12:15 am
Fireburst
Member Since: 02 Nov 2017
Location: Hertfordshire
Posts: 195
Hi, just curious about how you can eliminate the crank sensor by checking for movement? When mine went it was simply a failure of the sensor not a visible problem with the sensor.
Good luck with finding the fault, I changed the alternator, starter motor and battery before I found it to be the crank sensor on mine. My iiD tool just kept showing no faults!
30th Mar 2024 11:21 am
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Hi, the crank sensor has been replaced approximately 3 months ago by main dealership. Unless it’s gone bad. I was checking the crank movement for crank shaft failure.
31st Mar 2024 1:49 am
GreatWhenTheyWork
Member Since: 26 Jun 2023
Location: Kent
Posts: 35
Update, following Robbie’s thread….
Lpfp is pumping 1.4 Ltrs in a minute.
Pump pressure at the test point in the engine bay is a steady 6 psi, while cranking.
I rigged up a fuel pump and fuel supply to feed into the test point, the engine did try to fire twice but that was it.
I still need to dig into the engine bay and check the hpfp belt, a job for the weekend.
Could it be an issue with a cam position sensor ?
3rd Apr 2024 6:01 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5061
Are you getting any codes other than the ones for the oil temp and level? What is the battery voltage?
Make sure you include "pending faults" when scanning.
If the HPFP belt had snapped there will be a code for the high pressure fuel rail "system pressure low" or actuator stuck, I'm wondering if your problem might bigger than that?yµ (idµ - eAµ) ψ=mψ
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
