Member Since: 03 Oct 2018
Location: Kent
Posts: 619
Had the dreaded whine for a while now must get round to swopping it out iv got 1 sat here in the box but voltage is all good so unless it fails il wait for better weather
13th Dec 2023 4:12 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 619
Click image to enlarge
13th Dec 2023 4:18 pm
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6764
It didn’t look (like everything on YouTube) like a bad job but I decided to give it to the Indy as they were able to source the Denso alternator in less than a day and it’s -10 outside…
It’s cool to do things in the summer but it’s not fun to this time of the year outside
13th Dec 2023 7:13 pm
Mossy
Member Since: 01 Jul 2005
Location: Hollyoaks, UK
Posts: 2687
18 years of V8 ownership from new
Still my favourite car of my ever growing fleet.... No really!!! [/list]D3 HSE V8...
16th Dec 2023 7:51 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 619
Got it dirty
Click image to enlarge
16th Dec 2023 9:26 pm
Duc750
Member Since: 07 Aug 2017
Location: northampton
Posts: 315
Lrstaylor wrote:
Click image to enlarge
Add 1 to that as mine shows up on how many left as a manual S (its and auto HSE)05 D3 V8 HSE, LR Passion tree bars, wildbear compressor guard, LRP switch panel, ARB rear locker + compressor, Trigger 6 shooter electrical system
12 RRS SDV6 HSE (Hers) - Gone and replaced with an I Pace - I can tell you now EV is not the future yet
Metalian Camper trailer
10th Jan 2024 1:56 pm
Tim.S
Member Since: 30 Mar 2024
Location: Bristol
Posts: 10
Ive just got one
30th Mar 2024 6:22 pm
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6764
I’ve been chasing a lean bank 1, bank 2 or both condition over the last 6 months. It comes and goes. Sometimes a few drives one after another, sometimes weeks without anything showing up.
Have changed O rings and such, checked the air ducts for leaks, etc. etc. essentially trying to diagnose but attempting to avoid blindly throwing the parts cannon at the problem
I’ve used my trusty IID for this, particularly the live values, recording and exporting to PDF. I’ve been looking at short term trims, long term trims, O2 equivalence ratios and finally the observed requested mass air flow values. In particular with the last two I noticed that they tended to diverge quite a lot (requested 50, actual 30, etc.). Also the trims were all over the place often between 10 and 20.
About the only thing I figured out it wasn’t was O2 sensors since the equivalence ratios constantly looked fine with both banks very close to 1.0.
A friend wondered whether the current MAF sensor would be “tired” because they can age. I had applied CRC Airflow cleaner a few months ago when this happened the first time. It doesn’t do miracles, it seems
So, kind of on a lark decided to replace the current MAF sensor - which upon inspection turned out to be a genuine LR part manufactured in 2004 by Denso - with a brand new one also from Denso. The Denso part is DAN113, cost me 159 eur VAT 24%...
Based on the vehicle’s behavior after the swap it was well worth it! It seems like the car is more performant, it doesn’t hesitate at all when putting the pedal down and the trim spreads are very tight near zero. Also now the requested and actual MAF rates are constantly close to each other unlike with the previous sensor.
I’m amazed so far. I’ll see if it affects fuel consumption, too. One would imagine it does.
Hopefully this concludes the lean hunting for now. Knock on wood and all that.
18th May 2024 7:12 pm
Tim.S
Member Since: 30 Mar 2024
Location: Bristol
Posts: 10
Ive been working through possibly a similar problem. Lumpy idle and a slight misfire at about 1000-1200 rpm. I had lean mixture codes and the long term trim was up around +10 to 12.
So far Ive found that a previous owner managed to strip the threads where the EGR valve attaches to the throttle body elbow allowing air to be drawn in there.
18th May 2024 8:36 pm
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6764
Replaced coolant expansion tank.
Replaced the expansion tank to radiator return and EGR return hose (PCH500153)…. I was a cheapskate and bought a Gates branded one for 25 euro or roughly 1/2 price of genuine. A word of warning: The jubilee clips on it were too tight at the radiator and EGR end 🤯 situation was saved by reusing the old clips from the old hose.
Replaced the heater core. Took a lot of pictures.
9th Jun 2024 7:39 pm
Rumbling Disco
Member Since: 02 Dec 2013
Location: Stockport
Posts: 5
Replace narrow coolant pipe/ hose
We love ours! 05 Silver HSE as is common (well, as common as you can be with around 340 in UK)
Anyone know about changing the coolant hose that leads to the coolant tank?
Broke while green laning. Bought the replacement, but can’t see how to get at the far end clip!
Thanks
17th Jun 2024 8:23 am
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 619
Take the headlight out makes it much easier
17th Jun 2024 8:39 am
maccers
Member Since: 08 Dec 2012
Location: SE Kent
Posts: 276
May be a simple one - does anyone know a part number/size on the O-ring on the MAF sensor?
Took mine out for a clean and the o-ring is stretched and not offering a perfect seal.
Mislaid my verniers and none of my selection fit!
22nd Jun 2024 2:25 pm
kajtzu
Member Since: 10 Aug 2017
Location: Helsinki
Posts: 6764
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
