One question - did you keep the rack fairing, and if so do you need it anymore? I picked up a rack missing one; I'm trying to source one, or may just cut the rack down, as I quite like that look.
Cheers!'80 109 Stage 1 V8 - still going strong!
'13 LR4 HSE - HD pack (sold)
'11 LR4 HSE - HD Pack (sold)
'07 LR3 V8 SE (sold)
Ex '85 110 County V8 (left in Oz)
I'm wanting to run BFG MT's on an 07 LR3. The 2 sizes they have for 18" is 33.7x11.5 or 32.6x12.2.
I see your Nitto's are 33x12.6.
I'm putting them on an 8.5" rim with 30mm offset.
I'm also planning to use the coil over conversion. Which I think gets me 2.5"
I'm curious about which size you think will fit best with out too much rubbing.
Thanks
24th Dec 2012 9:50 pm
Reddahaydn
Member Since: 02 Mar 2015
Location: Melbourne
Posts: 38
Love your set up mate!
Looks the business!
I can confirm your previous post about the spacers.
I put 1" upper ball joint spacers in my old 4runner, which translated to approx 2.5" lift.2007 Disco 3 2.7 TDV6
LLAMS / 265/65/18 BFG ATs / Safari Snorkel / Spare wheel carrier / 100L Long range tank / Traxide SC40 dual battery isolator / Optima Yellow Top / Autologic Remap / Front Runner Slimline II Roof Rack / Cross drilled and slotted rotors and ceramic pads / Front Runner drawers / UHF / Rasta front skid plate / Waeco CF50 / Mitch Hitch / Tint / Parrot MKi9200 Bluetooth Phone & Audio
22nd Apr 2015 10:03 pm
jwest
Member Since: 09 Jun 2006
Location: USA
Posts: 114
disco4x4au wrote:
roveribis wrote:
Today I made some adapters to move the reservoir 1" deeper (into the ARB) and higher.
.
You can refit the reservoir in front of the battery - the existing pipework will reach.
Cheers,
Gordon
For anyone learning from this thread, the "space in front of battery" is best suited to location of on board air compressor to keep it high and away from water and dirt.96 Disco I, 210,000 miles - still going strong
04 Disco II, Vienna/Tundra, +2" lift, onboard air, 120V...
07 LR3 HSE
2008 Audi S4 Avant mt6
19th May 2015 6:19 am
TerryO
Member Since: 25 Aug 2011
Location: Goulburn, NSW
Posts: 13
Does anyone know if this project was completed in the end? The op got up to the stage of needing to modify the plastic wheel arches and that was the last thing I can find.
If there is another thread some where I would appreciate a link.
cheers,
Terry.D3 HSE TDV6 & D4 V8
5th Feb 2016 11:19 pm
~Rich~
Member Since: 16 Mar 2009
Location: Sydney
Posts: 628
Have you seen this thread Terry?
http://www.disco3.co.uk/forum/topic56336.html2014 SDV6 HSE White, LLAMS Height Controller, Tinted Glass, Tuff Ant Sliders and 18" steel wheels, Safari Snorkel, Rhino Rack Platform, ARB Air Compressor, Custom Drawer and storage unit -http://www.box.com/s/jem0ilac3cner2mexq64 UHF CB, 4x4 Intellegence RWC, 120ltr Long range tank, Rock Sliders and Compressor protection plate Beanie grill, De Tango.
5th Feb 2016 11:46 pm
~Rich~
Member Since: 16 Mar 2009
Location: Sydney
Posts: 628
http://www.disco3.co.uk/forum/topic57723.html2014 SDV6 HSE White, LLAMS Height Controller, Tinted Glass, Tuff Ant Sliders and 18" steel wheels, Safari Snorkel, Rhino Rack Platform, ARB Air Compressor, Custom Drawer and storage unit -http://www.box.com/s/jem0ilac3cner2mexq64 UHF CB, 4x4 Intellegence RWC, 120ltr Long range tank, Rock Sliders and Compressor protection plate Beanie grill, De Tango.
5th Feb 2016 11:52 pm
TerryO
Member Since: 25 Aug 2011
Location: Goulburn, NSW
Posts: 13
Thanks for that Rich.D3 HSE TDV6 & D4 V8
6th Feb 2016 1:54 am
D3 MILLSY
Member Since: 08 Dec 2016
Location: Perth
Posts: 8
Sorry to pull up a old post. But Ive sent emails off to Toddsco suspension with no response, Are they still in business?. I have a 2005 D3 with factory coils and would like to fit their strut spacers to my Disco. Even with the 50mm heavy duty Kings coils ( 14HD rear and 13HD front its still needs a bit more clearance).
Thanks
Millsy
Click image to enlarge
8th Dec 2016 2:12 am
PJS
Member Since: 19 Dec 2018
Location: Tamworth
Posts: 2
Having the same problems and for some reason their online shop does not list Australia for shipping....yet it does for NZ???????
29th Dec 2018 9:51 pm
D3 MILLSY
Member Since: 08 Dec 2016
Location: Perth
Posts: 8
PJS. I didn’t have any luck, so orderd some extra heavy duty rear coils from Dobinsons
314mm free length for the rear ( part # C51-137 )
Currently still running the Kings +50 mm heavy duty fronts
Height measurement are
Front: rim centre to flare 530
Rear: rim centre to flare 590
Full of fuel 180L
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
