DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
*Transmission Fault - Special Mode Not Available* |
|
Hey again!
So as above, upon starting the car you get this message:
*Transmission Fault - Special Mode Not Available*
I've done some searching around both on here, and on other forums, I tried a new module from eBay and that did not do the trick, I also put a new battery in the car and that also did not deliver!
HDC does work, as does higher and lower suspension.
Other faults with the car include reversing beepers not working.
I'd be grateful for suggestions as to where to look next!
|
19th Jun 2021 10:30 pm |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
You need to read the fault codes Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
19th Jun 2021 10:43 pm |
|
|
KevinD3
Member Since: 05 Aug 2020
Location: Sutton Coldfield
Posts: 1261
|
Hey Lawis, welcome to the forum probably the most common phrase you’ll hear on here is “read the codes”. It’ll help you start to pin down the cause.
If you haven’t got a code reader it’s well worth the spend, will save you £££££’s in trial and error and garage bills.
The faults on these can be caused things you wouldn’t even think of swapping out so reading the codes is a must if you can.
Also use the search on the forum, most faults have been discussed (and mostly fixed) before, as a starter, take a look at this one, similar fault
https://www.disco3.co.uk/forum/mutliple-fa...+available 2008 HSE Stornoway Grey
My Wife thinks the D3 is a hobby, The D3 thinks the wife is 💕
|
19th Jun 2021 10:48 pm |
|
|
KevinD3
Member Since: 05 Aug 2020
Location: Sutton Coldfield
Posts: 1261
|
Lol Ajax, I took waaaay too much time posting mine but great minds 2008 HSE Stornoway Grey
My Wife thinks the D3 is a hobby, The D3 thinks the wife is 💕
|
19th Jun 2021 10:49 pm |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
Thanks guys!
I've got a few actually! But we'll see if any of them work on the Disco!
|
19th Jun 2021 10:58 pm |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
You need a specfic type of reader to read all the codes on a discovery, a generic code reader will read basic fault codes but may not pick up all of the codes.
Luckily you can get an Autel reader for under £50 if yours doesnt read the codes Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
20th Jun 2021 7:57 am |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
Yepp as predicted by you guys, neither of them worked!
I'm now literally drowning in options of code readers hahaha! Had a search on the forum and it's horses for courses..
Ordered this one.. ..let's see!
https://www.ebay.co.uk/itm/363403038919?ep...ition=1500
Haha
|
20th Jun 2021 1:03 pm |
|
|
Mr Kington
Member Since: 12 Dec 2011
Location: Scottish Borders
Posts: 1552
|
My suggestion is give the battery a good charge and the messages will go away. They are just communication checks that don’t complete. Hence pop up. I used to get the messages a lot in the winter or after a series of short journeys. May not fix your problem but a cheap starting point James favourite hobby is writing in the third person.
|
21st Jun 2021 4:47 pm |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
So I cleared the fault codes with the Autel, and now it works ?! Time will tell if that's a permanent result!
|
27th Jun 2021 8:35 pm |
|
|
G3Z
Member Since: 16 Dec 2018
Location: South Wales
Posts: 553
|
The Autel pays for itself after just one use. Brilliant bit of kit. I always plug mine in and have a play to learn. Defender 110 2.4 TDCi Utility Station Wagon.
2007 Disco 3 GS TDV6 Manual
200,000+ mile club 😎
|
27th Jun 2021 10:22 pm |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
I spoke too soon!!
Jumped in the disco this AM and the fault returned!
Battery is new!
Fault codes are:
U0403-94 Invalid data received from transfer case control module
U01 32-87 Lost communication with ride level control module (but this does work)
P01 00-00 mass or volume airflow circuit
P0666-00 Powertrain control module engine control module transmission control module internal temperature sensor circuit
I did try another control module and that did not solve the problem.
🤷♂️🤷♂️
|
28th Jun 2021 12:13 pm |
|
|
Bungle
Member Since: 07 Apr 2015
Location: Wanborough
Posts: 256
|
I know it sounds daft, but check your brake lights. There is a known issue where if the bulb blows such that one of the two elements breaks and contacts the other (effectively joining the brake light and side light circuit together) the vehicle throws a transmission fault. I understand a number of dealers changed gearboxes under warrantee in the early days of the D3 before the problem was discovered......
|
29th Jun 2021 9:46 am |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
Interesting! I'll give it a check and see!
My reverse beepers also don't work and so ordered a new loom for the rear, will check all wiring on rear end and see what's what!
Thanks,
Lewis
|
29th Jun 2021 12:08 pm |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
Just had a thought,
On changing the transmission box, should I have then reset the code?
After I change the box I still got the error code on starting the engine, but anyone who has successfully beaten this error by replacing the box did you have to reset the error code for the error to go away?
|
1st Jul 2021 11:10 pm |
|
|
DiscoKick
Member Since: 19 Jun 2021
Location: London
Posts: 80
|
Hi all!
Sorry to double post, but can anyone confirm that when replacing the transfer case module, do you have to then perform a codes reset via an OBD tool to ensure the area doesn’t come up again?
For example, I tried a new transfer case module, installed it and then started the car however the error message came up again. I therefore assumed it wasn’t the transfer case module that was at fault, and put the old transfer case module back in again, re-selling the new one on eBay.
Should I have instead reset the code and then maybe, it would have worked just fine
|
25th Jul 2021 9:40 pm |
|
|