Member Since: 06 Mar 2017
Location: Lost
Posts: 5059
Thats interesting, is the supplier acknowledging his module may have a fault?yµ (idµ - eAµ) ψ=mψ
13th Mar 2021 10:28 pm
itguy
Member Since: 30 Dec 2009
Location: Melton Mowbray, Leics
Posts: 181
Yes and no - they have said that they have sold this module many times over to a wide range of people with all sorts of cars including the D3 and haven’t had any problems before. BUT, I did point him at this thread so he could see the issues Scwede was having too and we (the seller and myself) naturally came to the conclusion that there must be something strange going on.
He said he wants to understand it more and fix it too for any other sales, but he can only do that by getting hold of the exact same Webasto heater we have in the D3.
He did also mention that most of his customers disconnect the CAN / car control of the FBH and just use it manually via his w-bus unit as that means you can always give a decent burn time on the unit which is much better for it’s health.
I suppose in that scenario, I can see how he may not have come across this problem before.
14th Mar 2021 6:13 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5059
So the burning question is (excuse the pun) do other members on here using this controller have this issue also?
It may be they haven't noticed it, or its just not a problem for them. I doubt however they have all pulled the LR interface without a least one posting back here of so doing!
There's a lot to be said though for allowing the burner to reach full temp. Longer service life and less maintenance intervention for a start .yµ (idµ - eAµ) ψ=mψ
14th Mar 2021 9:17 am
itguy
Member Since: 30 Dec 2009
Location: Melton Mowbray, Leics
Posts: 181
Don’t know how many others on here will have the same controller, hence my continued updating of this thread and bringing it to the surface - if only to help someone else out in the future if they are trying to troubleshoot their own issues.
I have no idea how many people would have their own code scanner, let alone WTT software and w-bus diagnostics cable, and then even want to try what I did to rectify the problem. As motolab has said on here before, this needs to be done VERY carefully and with as much knowledge as you can possibly muster on the subject. My fix seems to have worked for me, but that’s just me and everyone else needs to make their own mind up.
It will be interesting to see what the other (more basic) FBH controller I have ordered is like and if it causes any issues. I hope not...
14th Mar 2021 9:32 am
ballast
Member Since: 13 Apr 2007
Location: South Midlands
Posts: 185
Interesting. So you'll note early on in that previous thread that I said it seemed to lock the FBH out (bottom of page 2). On Hawkeye, it reported a general electrical fault. Clearing it sorted it, but only once or twice then it reoccurred if I used the remote. Removed it completely and the FBH fired up perfectly in line with usual operating parameters (i.e. below 5 degrees). Fires up with the Webasto software no problem too.
Annoyingly, just bought a D4 and that FBH won't fire up. Connects to the software, but errors when I try to switch it on. Passes individual tests. Comes back with a code 81 fault.
Trawling all these threads to try and sort it and hence, came across this....
Chris
24th May 2021 2:51 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5059
I think that's a "lock out" fault, clear it and/or pull the fuse and see if it will fire up, but the WTT software should provide more info on the fault.yµ (idµ - eAµ) ψ=mψ
24th May 2021 4:55 pm
jagbloke
Member Since: 06 Dec 2009
Location: leicestershire
Posts: 66
Just to add to my experience - I recently fitted a remote module from radurek.
My experience has been that it does start the FBH, but now the car based operation doesn't seem to work, and every few cycles I get a lockout that I have to reset by removing the power supply to the FBH.
When I read the codes suing my faultmate, they are -
B1A00 and U1A03. I rest these but they come back seemingly whatever I do and whatever order I use the remote to switch the FBH on and off.
Looks like I need one of the alternative units - but I am now concerned about whether I have the same firmware issue as itguy.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
