Rear timing belt or High Pressure Fuel Belt DIY for TDV6
My indi quoted me the magical figure of $3500 to do both belts. I thought even if I take a two weeks off work to do this it will be cheaper.
I thought that someone should put up some info on how to do this back belt. The front timing belt already has some great guides and isn’t hard to do. This is hard especially on the body.
If you have never done this belt before, your in for a real treat, it took me 4 afternoons to do and patience beyond measure. My car is a MY06 with a MY09 motor so some things are different.
This is a job that is doable but you have to be very patient and not lose your mind. Just take it slow it can be done and will save you a lot of money.
8th Jun 2020 12:12 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Lets go.
You have to remove the battery and the covers over the rear control boxes and remove all the connections on the first box then the first 2 connectors towards the engine on the second box.
Click image to enlarge
Click image to enlarge
8th Jun 2020 12:15 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
In this pic you see there is a cover that is split and at the back there is a tab on each side you depress and wiggle them out. You will have to remove at least the 2 bottom ones. This is difficult to do. The wiring Lome has to be able to move. This was my first afternoons work.
Click image to enlarge
8th Jun 2020 12:16 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
You then have to undo this fuel line to give you more room. Working out what to do to get the cover out took the rest of this afternoon 2. And then going to buy the tools.
Click image to enlarge
8th Jun 2020 12:19 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Next you have to remove this rubber pipe. Because of the angle it is on I bought a locking hose clamp tool which made it a breeze to get off and on.
Click image to enlarge
8th Jun 2020 12:20 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Remove the clips at the top. It slots into the bottom. Again this is different year to year with these covers. You then have to wiggle the cover out. It does come out be patient it will come out.
Click image to enlarge
8th Jun 2020 12:21 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
To remove the belt. I used a 10mm spanner that I bent inwards towards the motor to get onto the tension-er bolt and used another to lock it together to break the tension on that bolt. Then used a ratchet spanner to remove the whole thing. Afternoon 3.
Click image to enlarge
Click image to enlarge
8th Jun 2020 12:25 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Getting it back together. Run the belt around the gears first, make sure the top of the belt is tight and on the teeth right with no slack. Then slide the tension pulley up and into place. (Has to be done this way can’t be slide on after.) I found that getting the tension pulley into place first so it is placed flat and slid into the tab without the bolt is the easiest way to do it. Then put the bolt in and tighten it up to 24 N (I just did it up until it felt as tight as I dare to go). Recheck the belt and make sure it feels like it is on properly. Then pull the pin out.
With patience once again wiggle the cover back on and put everything back together. Afternoon 4.
Your done. You will have the scars on your arms and back of your hands to prove it.
8th Jun 2020 12:29 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
It's a pity I can't add a video showing the detail of the install. I know I missed some things but I did the job 2 months ago and have been meaning to put this up but only got time now.
8th Jun 2020 12:33 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4454
in 2010 Disco Mikey ut up a 'how to' including rear belt.
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
8th Jun 2020 12:36 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Yes, I did see and use his guide as well as other bits and pieces from other sites but mine was diffrent and I had to remove other things to get the cover out that wern't mentioned anywhere. This is a very frustrating job to do, you cannot see anything. I thought a bit more of a guide would be helpful to others. Hopefully others can put up Pics as well.
8th Jun 2020 1:18 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4454
More detail always useful Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
8th Jun 2020 1:24 pm
garrycol
Member Since: 06 Dec 2010
Location: Canberra
Posts: 1117
It was easier to just pay my indy $1200 to do the job - I supplied the parts including oil pump so all up about $1500.
8th Jun 2020 1:38 pm
Dave InOz
Member Since: 29 Jun 2016
Location: NSW
Posts: 37
Good for you
8th Jun 2020 2:31 pm
Oswiperus D3 Decade
Member Since: 02 Apr 2010
Location: Chelmsford, Essex
Posts: 1595
When I did both of mine 7 years ago, I took it nice and steady like you, Front belt one day and the rear belt the next day.
Those 7 years have flown by and now they are due again! Stu
2016 D4 Landmark current
2022 Defender D300 SE Gone
D4 2014 XS Commercial - Gone
D4 2016 hse lux montalcino red - Gone
D3 2005 se java black - current
D3 2005 base manual - gone
D2 1999 TD5 E white - current
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum