Thanks mate would I still need the cable they sell on the forum as wellRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
22nd Jan 2018 9:35 pm
markyzs180
Member Since: 21 Sep 2017
Location: West Midlandshire
Posts: 63
You need to have a red wire from pin 2 of the 8 pin connector on the FBH, then you can just use crocodile clips to connect to the pins on the OBD cable (one to the red fbh, +12v, -ve) and the WTT software your laptop
22nd Jan 2018 9:59 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18510
You need one of the diagnostic looms from the site shop AND the USB/OBD2 adapter from eBay.
Or home-brew a loom for yourself if you have the bits 06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
22nd Jan 2018 10:01 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18510
All details there including which USB adapter you also need.06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
Thanks for all the help and links I’ll buy the parts from the forum in the morningRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
Got the cables, downloaded the software followed the instruction on this thread and so far three starts and three runs no smoke all good thanks discostick for sharingRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
30th Jan 2018 4:21 pm
markyzs180
Member Since: 21 Sep 2017
Location: West Midlandshire
Posts: 63
Quote:
furnitureman
Post #1908345Posted: 30th Jan 2018 3:21 pm Post subject:
Got the cables, downloaded the software followed the instruction on this thread and so far three starts and three runs no smoke all good thanks discostick for sharing
glad you got it sorted and burning bud
1st Feb 2018 10:42 pm
iacsinte
Member Since: 09 Dec 2021
Location: Suceava
Posts: 8
CO2 adjustment not working on Thermo Test Software
Hi group,
I need your help on the following matter: These days I started working on fixing my webasto for my discovery 3, 2006. It was starting but turning off by itself in 30 sec. Thanks to this forum I managed to clean it, diagnose it and make it run. It has the 02h error. Blow on it and made it run. Still if I don't blow on it, it will stop.
So I tried the sugested aproach to increase the CO2 setting from Calibration => CO2 adjustment. Still, when the adjustment window opens I get the following error:
CO2 adjustment is not possible! The heating unit is not within the necessary operating state or adjustment value out of the valid range.
I have no other option but to close this window.
I used:
- Thermo Test software installer v2.14
- Thermo Test software installer v2.16.1
- Thermo Test software installer v3.4
Same error on all. VCDS pin configuration: 4, 7, 16. I think now that I never tried using pin 5 as ground instead of 4.
Do you have any suggestions for me?
As I see I have 2 options:
- increase the setting as you all did - but need your help to pass the error.
- mount a 12V fan to continously blow into the air inlet.
Many thanks!
11th Dec 2021 6:12 pm
Bizbauer
Member Since: 07 Oct 2014
Location: Edinburgh
Posts: 99
I have just encountered the same thing…
To adjust the CO2 level, the unit has to be running so start it from the software in ‘Parking Heater’ mode and once it’s up and running you should be able to access the CO2 adjustment.
Good luck'06 D3 TDV6 S Cairns Blue
Altox, D4 BT module
V8 Brake kit
Beanie Grille
'11 KTM 990SM-T
'01 Saab 9-5 Aero
Previous: '05 Freelander 1 HSE, Zambezi Silver
'97 Freelander 1.8, Black
18th Dec 2021 3:39 pm
iacsinte
Member Since: 09 Dec 2021
Location: Suceava
Posts: 8
Thank you Bizbauer!
I tried again today, with my improvised fan blowing and I left it run for about 10 mins. After that I was able to enter and edit the CO2 setting. Of course, while still running in "Parking Heater" mode.
I modified the value to something close to the maximum (last value before the maximum) and since then I tried 2 time without any blower help and seems to work perfectly.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum