Member Since: 18 May 2015
Location: Reading, Berks
Posts: 67
FBH won't run from Webasto software
Further to my previous posts, I bought the diagnostic loom from the shop here and happy news after clearing lock out faults the FBH runs again off both timed climate and auto running. I can also individually test the components from webasto software but for some reason cannot run FBH from same software using two available options of either supplementary or park heating. When selecting those options FBH status stays as off and occasional error of NAK: access denied. Any ideas?
23rd Jan 2017 9:55 pm
marco 110
Member Since: 15 Nov 2009
Location: SALLES 33
Posts: 1014
Had the same issue. I'll try another version of the webasto software..Marco.
-D4 sdv6 HSE 2012 , high beam assist , surround cam, tv , and a lot of nice stuff..
Member Since: 20 Nov 2016
Location: Stourbridge
Posts: 401
same problem for me.
9th Oct 2017 7:25 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18510
Sounds like a D4-related problem, everyone reporting this has a D4.
Does anyone have the link to the V3 software, I've only got V2 listed in the wiki.06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
11th Oct 2017 3:41 pm
Sly666
Member Since: 15 Dec 2014
Location: East Sussex
Posts: 459
Wouldnt work with my 2013 D4 using WTT version 2.14.
Same symptoms, Can run fuel pump, fan etc but not start the heater.
However does work with Ver 3.0 WTT.
You need to select W-Bus model and NOT the "VEVO" model heater. This then starts WTT 2.16 version.
When you start the heater using the software the cabin fan kicks in for a while then the FBH kicks in some time later. Be patient!
*** Martin *** Did you get my email about my FBH controllers i make?
Also the link to WTT download in the WIKI doesn't work anyway!
Regards.
Simon.
11th Oct 2017 11:33 pm
Sly666
Member Since: 15 Dec 2014
Location: East Sussex
Posts: 459
If anyone wants Version 3.0 Webasto WTT, please PM me
Simon.
11th Oct 2017 11:42 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18510
Hi Simon,
I will reply to your email ASAP, just been short of time this week.
The WTT 2.14 download link in the wiki was fixed earlier this afternoon, I wasn't aware that where I had put the file no longer worked.
Also have 3.0 (thanks Simon) and 3.4 (thanks Surfup03) to upload (both very large files) and link to the wiki.
I have managed to extract 2.16 from the 3.4 installation on its own and will be updating the wiki with a link tonight.06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
Last edited by Martin on 12th Oct 2017 12:18 am. Edited 1 time in total
11th Oct 2017 11:54 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18510
Sly666 wrote:
However does work with Ver 3.0 WTT.
You need to select W-Bus model and NOT the "VEVO" model heater. This then starts WTT 2.16 version.
When you start the heater using the software the cabin fan kicks in for a while then the FBH kicks in some time later. Be patient!
I assume you are picking WBUS less than 3.5 on the left not WBUS greater than 4.0 on right hand side?06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
12th Oct 2017 12:04 am
Surfup03
Member Since: 28 Mar 2017
Location: London
Posts: 16
Sly666 wrote:
Wouldnt work with my 2013 D4 using WTT version 2.14.
Same symptoms, Can run fuel pump, fan etc but not start the heater.
However does work with Ver 3.0 WTT.
You need to select W-Bus model and NOT the "VEVO" model heater. This then starts WTT 2.16 version.
When you start the heater using the software the cabin fan kicks in for a while then the FBH kicks in some time later. Be patient!
*** Martin *** Did you get my email about my FBH controllers i make?
Also the link to WTT download in the WIKI doesn't work anyway!
Regards.
Simon.
Hi guys pulling my hair out at this point lol.
How can cabin fans come on? I take it your not using the OBD adapter into the heater and not only using the car loom for fuel pump??
I'm having issues with the same. Ive used diffrent versions of WTT with no joy im now on 2.16 selecting W-BUS model But no cabin fan and even if I wait no heater ππ
I'm also getting an EOL Checksum error 81h. This is only when I pull fuse and energise again after clearing it's gone untill I pull fuse, I'm wondering if this the module being faulty. Is there any other way of turning this heater on apart from making the outside temp senser cold.
Thanks for your help in advance.
Luke
12th Oct 2017 12:17 am
Sly666
Member Since: 15 Dec 2014
Location: East Sussex
Posts: 459
Its a bit late tonight and tipping down!
I'll do it again tomorrow and confirm the exact settings.
12th Oct 2017 12:22 am
Sly666
Member Since: 15 Dec 2014
Location: East Sussex
Posts: 459
Martin wrote:
Sly666 wrote:
However does work with Ver 3.0 WTT.
You need to select W-Bus model and NOT the "VEVO" model heater. This then starts WTT 2.16 version.
When you start the heater using the software the cabin fan kicks in for a while then the FBH kicks in some time later. Be patient!
I assume you are picking WBUS less than 3.5 on the left not WBUS greater than 4.0 on right hand side?
Correct. The version which opened was 2.16
12th Oct 2017 12:27 am
marco 110
Member Since: 15 Nov 2009
Location: SALLES 33
Posts: 1014
Sly666 wrote:
If anyone wants Version 3.0 Webasto WTT, please PM me
Simon.
Thanks to you and Martin for this , i'll try it soon Marco.
-D4 sdv6 HSE 2012 , high beam assist , surround cam, tv , and a lot of nice stuff..
Member Since: 15 Dec 2014
Location: East Sussex
Posts: 459
Well, Eating a bit of humble pie here gentlemen!
I've put my D4 FBH on the diagnostic cable a couple of times and its fired up first time each.
So thought i'd try again last night...
The first time i used WTT V3 which loaded into 2.16. Bang...fires straight up.
So shut it down, and booted into the older 2.14 version. Bang... Fires up again. Weird i thought as it refused to run before with version 2.14.
So i switched back to V3.0 (2.16) and...nothing. Only the interior fan kicks in.
So back to 2.14. Same happens.
Reboot PC and hard reset FBH (pulled fuse), Checked for heater faults using WTT and my IID tool. None.
Then things got worse...Not even the interior fan would kick in.
Played with the port settings for my USB Serial diagnostic lead and set them the same as W-Bus Comms use. This made the interior fan run again, but the FBH would still not kick in.
Everything else works on WTT, just now refuses to start.
Tried the diagnostic lead on the D3 FBH, No problems.
Tried a different Diagnostic lead with an FTI chipset... Same.
Scratching head!
Next step is to snoop on the W-Bus commands going back and forth.
13th Oct 2017 5:01 pm
daviesto
Member Since: 18 May 2015
Location: Reading, Berks
Posts: 67
So full of optimising from the resurrection of this thread that I started, I downloaded v3 today, configured it for W-Bus and booted it up with 2.16.1. Unfortunately same result as 2.14 - diagnosis starts, comms and status all ok, can test individual components but can't start heater. I'm optimistic now that others have confirmed the problem that someone with the right technical knowledge will take up the challenge of solving this! Winter is coming and I want to get to the bottom of the run problems with my FBH!
14th Oct 2017 11:38 am
Jubbly
Member Since: 20 Nov 2016
Location: Stourbridge
Posts: 401
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum