Member Since: 09 Aug 2020
Location: Rotorua
Posts: 6
Discovery LR3 Comms Fault- Bus Signal B00D2
Greetings Tech Brothers,
Could I kindly speak to an intelligent life form with grey hair and wrinkles who worked on these things in 2005 to 2009 please?
Fault- B00D2 - Restraint System Malfunction Indicator 1
History - Flood in left side foot well- front and rear of a Righthand drive LR3
Tool -ICARSOFT LV2 Landrover scanner-real time results.
Thankyou
9th Aug 2020 5:15 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10673
Indicator = light.
Sounds like the dash light to me
The other light being the passenger disable light on the consol
9th Aug 2020 9:33 am
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1817
Remove the sill trim and check for bad connections on the 'twisted' wires. Check the connector under the seats - suggest you separate, clean and put back together - failing that it maybe the restraint ECM faulty especially if any of the restraints have triggered.
10th Aug 2020 4:50 am
Andrew Kiwi
Member Since: 09 Aug 2020
Location: Rotorua
Posts: 6
Discovery LR3 Comms Fault- Bus Signal B00D2 reply to friends
Hi guys ,
Thank you for your response.
This fault is a very tricky one that tests your intellect.
Heres a quick brake down of comms fault.
The SRS readout on right of the dash is active .
Air Bag light is lit to "40% only."
All resisters inside the Airbag circuit are of similar value
All steering buttons work ok.
Sky light leaked
Un plugged rectangle plugs front seat only and cleaned with CRC Contact cleaner and re fixed retainer hex screw.
Fault returned after clearing error with Icarsoft tool , but returned again after restarting Car.
So Lads,
I am wondering about the following .
1 . Does a faulty leaky drain leak onto a central fuse box somewhere around front passengers foot well, providing power to the SRS restraint circuit ?
2 . Dimly lit Air bag light might mean low power from fuse box to RCM restraint module activating a comms error alarm?
3 . an Earth point or Earth common connectors somewhere in floor or sill area that may have water damage .
4 . How to test safely -the cambus signals across the various points of th SRS circuit.
What would be reaaaaaaaly awesome to see some pictures of the Earth points - Connectors relating to Airbag Circuit - RCM Module removal - Door Airbag hing Plug - Fuse bank and anything you have.
Thanks Lads .
Wife has given notice that the Dog house has been prepared for me, and the Dog gets my bed if this
problems not fixed .
The Pressure is ON.
10th Aug 2020 7:36 am
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1817
Here is one that shows the earth connections
Click image to enlarge
10th Aug 2020 8:26 am
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1817
Check the cabin filter behind the glove box. If this is wet then the fuse box below it is suspect
10th Aug 2020 8:27 am
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1817
Member Since: 09 Aug 2020
Location: Rotorua
Posts: 6
Thankyou kindly for the info.
10th Aug 2020 8:35 am
Andrew Kiwi
Member Since: 09 Aug 2020
Location: Rotorua
Posts: 6
PCB instrument cluster intermittent PCB Fault
Cam bus not talking clearly to cluster.
Resolder Cluster plug and Contact clean plug and PCB socket.
Tap across back of PCB to force and clear fault with car on.
LCD module pins or socket could be an Issue.
Restart car to clear errors after repairs.
Scan tool to reset not required.
Andrew Kiwi
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
