do a search on ebay i think the company is called landyair or something similar they do alsorst of bits to refurb a compressorRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
may i ask do u guys refit the cover back on please
as the top cover is such a pain being in the way when trying to get it back on was wondering if it's ok to leave it off
or must it go back on plse
seen some air compressor guards but they are silly money
thks as always
id recommend you put it back as not only does it protect from being damaged it suppresses the sound making it less noticableRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
well there's me thinking i can wait till the spring, but my compressor has other ideas
put the iid on and got the following message
C1A13-64 (2C) Pressure does not decrease when venting gallery - Algorithm based failure - signal plausibility failure
read up on here and it seems it's the exhaust vent blocked , on a hitachi pump
trouble is how the hell do u get it out please ,
have got the rebuild kit and new piston seals, exhaust bolt etc, just waiting for the pushfit connectors
is it safe to use a blow lamp , but am concerned as its aluminium will cause more damage , or maybe a paint stripper hot air gun
soaked it in wd40 , it will get a can of plusgas
did hear about using the tip of a soldering iron to try and free it off , but worried i may do some damage
tried a socket but has rounded off
wondering can u drill it out or would i end up in a world of hurt
just wondered how the hell u managed to get it out please
thks so much in advanced
i would say that the not venting is more to do with the dryer beads being blocked this stops the air from venting open up the dryer and have a look inside before going any furtherRange Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
14th Nov 2016 5:31 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
furnitureman wrote:
id recommend you put it back as not only does it protect from being damaged it suppresses the sound making it less noticable
thks mate for that
found i can't get the collets , the 10mm one, so i may have to buy a new compressor , dunlop one to replace the hitachi
is mad there not available
if i do will then sell all the overhaul kit etc and the new dryer caps
14th Nov 2016 5:43 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
furnitureman wrote:
i would say that the not venting is more to do with the dryer beads being blocked this stops the air from venting open up the dryer and have a look inside before going any further
think i may not be able to repair it due to these collets
but thought if i get a new one at least all the suspension will be done and dusted
14th Nov 2016 5:44 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
furnitureman wrote:
do a search on ebay i think the company is called landyair or something similar they do alsorst of bits to refurb a compressor
got the full repair kit , been looking on ebay , amazon etc for them
also seen a small split in the 4mm pipe
is getting to the stage where it's beyond repair really
have a look on here they sell the bit with the colets in http://www.ebay.co.uk/usr/original_landyai...2749.l2754Range Rover Westminster 4.4 TDV8 what a car
Discovery 3 HSE 2006 gone but never forgotten
Member of the 234,567 mile club😎
14th Nov 2016 7:28 pm
Countlouis
Member Since: 16 Nov 2016
Location: Walsall
Posts: 4
Air compressor issues
Hi all I have the orange light come on everytime the air compressor get to pressure and cuts out I have done the rebuild kit everything works ok before light comes on
I also have now I rebuilt compressor it says over heating will raise when cools down
Ant ideas ???.
16th Nov 2016 5:39 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
thks, bought a new compressor in the end , was getting to the stage when it became beyond economical repair
16th Nov 2016 5:40 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
Re: Air compressor issues
Countlouis wrote:
Hi all I have the orange light come on everytime the air compressor get to pressure and cuts out I have done the rebuild kit everything works ok before light comes on
I also have now I rebuilt compressor it says over heating will raise when cools down
Ant ideas ???.
not 100 percent but there something about the vent plug,
assume u replaced all the silica
16th Nov 2016 5:42 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
10mm collet obsolete trick
know i'm fitting a new compressor but refuse to throw away my old hitachi pump all for an obsolete 10mm collet
had a look and could see it had a brass sleeve
so thought i would give it a go
can now then get a male to pushfit fitting to go onto the ends and rebuild the rest at my leisure
assume it's been done before , but on the off chance wished to share what i did
16th Nov 2016 10:25 pm
Countlouis
Member Since: 16 Nov 2016
Location: Walsall
Posts: 4
Re: Air compressor issues
gstuart wrote:
Countlouis wrote:
Hi all I have the orange light come on everytime the air compressor get to pressure and cuts out I have done the rebuild kit everything works ok before light comes on
I also have now I rebuilt compressor it says over heating will raise when cools down
Ant ideas ???.
not 100 percent but there something about the vent plug,
assume u replaced all the silica
yes I did and all new seals as well if the orange light does not come on then the system works fine even to levelling when we get out like it should ?
after a few days orange light has gone off and not come back leaving for days
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
hell do u get it out please ,
