Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Technical (D3)

suspension
Post Reply  Down to end
Page 2 of 2 <12
TC179
 


Member Since: 19 Aug 2014
Location: uk
Posts: 145

England 

Cracked air dryer, corroded contacts etc.
  
Post #149214824th Jun 2015 10:11 am
View user's profile Send private message View poster's gallery Reply with quote
torlak
 


Member Since: 22 Sep 2014
Location: London
Posts: 42

United Kingdom 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

forgot to add that my D2 with active cornering enhancement had better handling and less body roll than the D3.
would that be related to any of the above codes?
  
Post #149216424th Jun 2015 10:54 am
View user's profile Send private message View poster's gallery Reply with quote
maplecottage
 


Member Since: 01 Feb 2011
Location: Norfolk
Posts: 3171

United Kingdom 2006 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

iand3 wrote:
Mine is currently sat on its bump stops with a similar fault. I have the red 'wobbly car' symbol and also HDC/special programs off etc.

Mine is due to a faulty steering angle sensor apparently. My steering angle was giving 5640 degrees!!

I have a replacement (S/H ebay). Though I plugged it into the car without fitting it to the column to see if the car recognized a working sensor, but still no joy!

I think it needs calibrating and configuring. So its off to the garage on Sat to be left with them. Assuming i can drive it there!!


Calibrating the steering angle is a 5 minute job - you may well have a forum member close to you who could help you for a couple of beer tokens - loads cheaper (and quicker) than getting the garage to do it.
  
Post #149217924th Jun 2015 11:52 am
View user's profile Send private message View poster's gallery Reply with quote
Discogaz
 


Member Since: 17 Mar 2014
Location: Bracknell
Posts: 1399

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Cairns BlueDiscovery 3

Hi Torlak.

That was my biggest suprise when moving from a D2 with ACE to a D3, loads more body roll
and nowhere near as good handling but waaaay smoother.
  
Post #149218424th Jun 2015 12:03 pm
View user's profile Send private message View poster's gallery Reply with quote
torlak
 


Member Since: 22 Sep 2014
Location: London
Posts: 42

United Kingdom 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

Discogaz, yes i am very surprised that body roll is a lot more on D3 than D2. that ACE system rocks, apart from the fact they may leak as the pipes corrode..i had to take the whole system off and install conventional roll bars but even with roll bars she had less body roll than D3.......
  
Post #149218724th Jun 2015 12:19 pm
View user's profile Send private message View poster's gallery Reply with quote
Discogaz
 


Member Since: 17 Mar 2014
Location: Bracknell
Posts: 1399

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Cairns BlueDiscovery 3

Apparently a LR sport has ACE.
  
Post #149272425th Jun 2015 6:29 pm
View user's profile Send private message View poster's gallery Reply with quote
Discogaz
 


Member Since: 17 Mar 2014
Location: Bracknell
Posts: 1399

United Kingdom 2008 Discovery 3 TDV6 HSE Auto Cairns BlueDiscovery 3

Meant RR Sport. Who'd have thought a lump like a D2/RRS could handle like a go kart. Sort of.
  
Post #149272725th Jun 2015 6:30 pm
View user's profile Send private message View poster's gallery Reply with quote
torlak
 


Member Since: 22 Sep 2014
Location: London
Posts: 42

United Kingdom 2005 Discovery 3 4.4 V8 HSE Auto Zambezi SilverDiscovery 3

ok here is what i did so far for the suspension but still getting the same fault code hdc fault, special programs off, suspension lowered ... etc

hard reset
replaced the brake switch
replaced the battery (old one was 10 yrs old anyway)
checked connections under the battery and no signs of water/corrosion - looked very very clean in fact

i had cleared all the old fault codes straigth after replacing the battery but after about 25 min of driving got the same lights on the dash board and the code read;

U0416 invalid data received from vehicle dynamic control module - bus signal/message failure - signal is invalid - pending

not sure what to look at next...pls help..
  
Post #149419728th Jun 2015 9:05 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 2 of 2 <12
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site