Member Since: 19 Nov 2009
Location: Leeds
Posts: 192
Access through the bulkhead
Could any body point me in the right direction for gaining access through the bulkhead with my wiring to connect wiring loom for FBH diagnostics.
any short cuts or what not to to do please
regards
DougWeekends are to short
Egr valves removed
17th Jan 2015 10:01 am
Andy Foster
Member Since: 27 Dec 2009
Location: Liverpool
Posts: 6551
Open up the 2nd battery box, the one in front of the driver. If you have a look in there you can see a grommet which gives you access to just under the steering wheel. Will try and find a photo
Cheers
AndyD4 MY15 SE TECH
D3 gone but never forgotten.
17th Jan 2015 10:10 am
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Someone will be along shortly with the best route through to the bulkhead grommet but I do question the effort for FBH diagnostics.
I find it easier to do it all from the outside even when owners have enabled the OBD port. From the outside you can hear and understand the entire start sequence, check actual temps and even get an educated nose for the correct smell. The inside of the vehicle is just too isolated, even if it does provide protection from the elements.
Land Rover - Turning Drivers into Mechanics Since 1948
Slight snap you seem to have a manual - the easy gromit will be filled with clutch rods. Though I think there is another one, but is harder to get to. Butr same general area - but nearer the edge of the car.Mark.
2006, D3 SE Auto - gone but not forgotten.
2014 BMW 530d M Sport Tourer.
1977 Triumph Spitfire 1500
_________________________________________________
Disco Picture Website Here
17th Jan 2015 10:29 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20786
Member Since: 05 Sep 2014
Location: Newquay
Posts: 1014
Robbie wrote:
Someone will be along shortly with the best route through to the bulkhead grommet but I do question the effort for FBH diagnostics.
I find it easier to do it all from the outside even when owners have enabled the OBD port. From the outside you can hear and understand the entire start sequence, check actual temps and even get an educated nose for the correct smell. The inside of the vehicle is just too isolated, even if it does provide protection from the elements.
Slightly off topic here but another brain teaser for Robbie
You mentioned the OBD port and FBH. My 05 plate D3 has the red W wire already installed on the FBH plug. Would you know if this is already wired to the OBD port?
CheersFreelander SE 2005 Auto.
D3 TDV6. Gone.
05's had pin 2 connected from the factory.Mark.
2006, D3 SE Auto - gone but not forgotten.
2014 BMW 530d M Sport Tourer.
1977 Triumph Spitfire 1500
_________________________________________________
Disco Picture Website Here
17th Jan 2015 11:43 am
bigtam64
Member Since: 19 Nov 2009
Location: Leeds
Posts: 192
Is it possible to use a USB extension instead of going through the bulkhead
Weekends are to short
Egr valves removed
17th Jan 2015 1:31 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Nodge68 wrote:
Slightly off topic here but another brain teaser for Robbie
You mentioned the OBD port and FBH. My 05 plate D3 has the red W wire already installed on the FBH plug. Would you know if this is already wired to the OBD port?
Cheers
Well I cannot account for how individual cars have been modified but as standard the red wire, where fitted, is not connected to the OBD port. The red wire to Pin 2 was deleted from 06-09 cars but is present in cars pre and post these years.
What did I win?
D3:
Click image to enlarge
D4:
Click image to enlarge
Click image to enlarge
Land Rover - Turning Drivers into Mechanics Since 1948
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum