Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
D3 non starter at -2 and below
Hi all, just joined the forum and hoping someone can help me with my d3's starting issues. When the temp drops below -2 the car cranks over fine but will not fire. After reading topics on here I'm almost certain is battery/glow plug issue. I've had the car plugged in to a solus code reader which showed nothing. Had the battery tested and it was a little below par (100a/h, 850cca) just rejuvenated that with a good 48hr charge. Tried to test the glow plugs with multimeter but there's no resistance on any of them and there isn't 12v at the main multi plugs on top of the engine. The relays are ok as are the fuses. Really baffled here??? Can anyone give me some instruction on the best way to test the plugs to ensure I'm doing it properly? I love the car but if I can't get it reliable I'm snookered. Thanks in advance for any help. Cheers
16th Dec 2012 12:46 pm
daz216
Member Since: 24 Jun 2011
Location: walsall
Posts: 70
mines the same mate,i usually turn the ignition on & off a few times but when it starts its a bit lumpy deff glow plugs morris marina x 2
ford granada 2.8
rover vitesse 820 turbo
rover 827
subaru wrx sti prodrive
volvo s60 t5 2.5 turbo
vw touareg r5
ford focs st
subaru wrx sti
vauxhall insignia vxr
landrover discovery 3 hse {the dogs}
16th Dec 2012 1:01 pm
Discoveryjon
Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
Cycling ignition doesn't help on mine because there's no power to them at all, and I don't think any of the glow plugs are working???? Unplugged the multiplugs on top of the block this morn, glow plug light came on as normal (about 10 secs) and then it started fine. Relays are clicking in and out but still no power at plug?
16th Dec 2012 1:10 pm
hgbosch
Member Since: 25 Oct 2010
Location: Pretoria and Zürich, Switzerland
Posts: 188
Discoveryjon wrote:
Cycling ignition doesn't help on mine because there's no power to them at all, and I don't think any of the glow plugs are working???? Unplugged the multiplugs on top of the block this morn, glow plug light came on as normal (about 10 secs) and then it started fine. Relays are clicking in and out but still no power at plug?
Hi
sounds like a glow plug issue to me. What is the mileage on your rig?EX AFRICA SEMPER ALIQUID NOVI
SEMPER IN FAECIBUS SUMUS SOLE, PROFUNDUM VARIAT
with kind regards
George Bosch
2005 Disco3 TDV6 S
2003 Range Rover Td6
1998 Disco1 ES 300Tdi (sold)
And some more serious stuff
16th Dec 2012 1:35 pm
Discoveryjon
Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
Mileage is 141 thou. Can't understand why there's no power at multiplugs?
16th Dec 2012 1:40 pm
Discoveryjon
Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
Anyone got any ideas? Any help much appreciated
16th Dec 2012 7:40 pm
manichauhan
Member Since: 24 Oct 2010
Location: London
Posts: 56
Try a hair dryer to see if it makes a difference. In your case, the problem appears to recur, so perhaps there is a more complex problem.
Good fuel? Maybe it is getting a bit viscous?Volvo XC60 - does all that the D4 should have done
Discovery HSE MY16 (good apart from the heating), now sold
Audi TT Roadster (wow)
MGB Roadster (owned since 1992)
Discovery 3 TDV6 HSE MY08
Saab 9-5 Aero 2002 (gone but not forgotten)
16th Dec 2012 9:06 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 72908
At a poultry -2c? Bog standard el cheapo supermarket stuff would be fine at that.
16th Dec 2012 9:09 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Unusual not to have power on either loom. Are you sure you have checked all relevant fuses (Link 1E, Link 4E plus Relay R114 etc), if so try a hard reset as the ECM triggers most glowplug activity?Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
Cheers for your replies, I've tried the 2 50 amp fuses and the 2 relays next to the battery and they're ok. Already done hard reset but will try again. Where is the ECM? Also ontop of the glow plugs is the plastic part which the loom plugs in to, how do you remove this to access the glow plug itself? Thanks again for replies
16th Dec 2012 10:04 pm
Discoveryjon
Member Since: 16 Dec 2012
Location: South yorkshire
Posts: 7
Any more ideas? I've tried hard reset to no avail, and I've shorted the relay holder and still no power at the plugs on top of the engine? Are there any fusible links between the relay and the multiplug or am I missing something really obvious? Thanks
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum