Member Since: 14 Oct 2005
Location: Somerset
Posts: 1145
Bulletin: LTB00420v2
This version has been issued to add pre 10MY vehicles.
Manufacturing have previously used two different types of air suspension compressors. See Below for applicable VIN Ranges. If the Hitachi or old-design AMK air suspension compressor requires replacement, then a new-design AMK air suspension compressor can be installed.
Hitachi air suspension compressor fitted from VIN:
Discovery 3/LR3 - 5A000360 to 9A513325
Range Rover Sport - 5A900302 to 9A215622
Hitachi or old-design AMK air suspension compressor fitted from VIN:
NOTE: Some vehicles may have been previously repaired using the old-design AMK air suspension compressor.
Discovery 4/LR4 - AA513326 to CA638964
Range Rover Sport - AA215623 to DA768550
NOTE: The Fault Code C1A20-64 may also be displayed.
Really as per Mikeys write up, then:
CAUTION: SDD must be loaded with DVD131.07 calibration file 118 loaded or later.
reflash air sus ecu
regards
Steve
8th Oct 2012 3:08 pm
santiD3
Member Since: 09 Jan 2011
Location: Navarra
Posts: 261
Very nice job Mikey
What is your feeling about new compressor???
18th Oct 2012 8:28 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20778
Its cheaper, easier to fit, has a more substantial mounting bracket, so should not corrode away (still wont take the weight of the car though, so don't jack it up there)
Member Since: 09 Jan 2011
Location: Navarra
Posts: 261
At least I hope that it lasts longer than the older ones.
18th Oct 2012 9:33 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20778
It seems to be a bit hit and miss as to how long the original ones lasted. Some were replaced under warranty, some are still original after 6-7 years...
I suppose the question should be, how many D4/2010MY RRS's have had replacement AMK compressors?
That said though, it seems as though the original AMK compressor has since been superseded from original D4, according to Steve Norman's post... My D3 Build Thread
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18506
Great write-up and information, thanks guys for sharing 06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
18th Oct 2012 9:56 am
Q86ARR
Member Since: 23 Feb 2010
Location: Jersey
Posts: 378
Disco_Mikey:
Service action Q213 has recently been released. This is to replace any Hitachi compressors that were changed under warranty to AMK compressors.
AMK compressors are now fitted from factory and the only compressor available from factory, for Disco\Sport and also FFRR!
20th Oct 2012 3:40 pm
discoBizz
Member Since: 20 Sep 2008
Location: Manchester
Posts: 1416
Member Since: 18 Sep 2011
Location: Melbourne
Posts: 17
Any particular way? It must be a very snug fit!
Also any ideas to trouble shoot the faults I am having?
I am yet to get the software update and was trying to find someone close with a fault reader to help understand them and clear them.
9th Dec 2012 9:53 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20778
Disco_Mikey wrote:
It goes into the end of the hard plastic pipe, collar end in first
It helps to soften it up by leaving it in boiling water for a short while. The plastic expands, and becomes more pliable, and is quite easy to push it in then My D3 Build Thread
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum