Member Since: 05 Mar 2011
Location: chengdu
Posts: 1542
D4 left hand drive blackvue install guide
hello, after my short trip back to the UK I picked up a blackvue and have just installed it. Took some photos to show. Not a hard job thanks to previous posts on the subject.
step 1 prepare a fuse I butchered a fuse like this (still retaining its fuse like function)
Click image to enlarge
Step 2
grap the the front and pull back and down
Click image to enlarge
step 3
This is the mirror surround stick a finger in here and seperate the two sides (they just pull apart)
Click image to enlarge
step 4
Remove the "airbag" plastic cover on the pillar and remove the self tapping torque screw pull away the door rubber
Click image to enlarge
step 5
Notch the mirror cover for the cable to pass through
Click image to enlarge
step 6
open lower glove box and press the guides to allow it to fully open
Click image to enlarge
step 7
Remove entry assist handles
Click image to enlarge
step 8
Feed a stiff piece of wire along here until it pops out near the curtesy light cluster
Click image to enlarge
Its popped out
Click image to enlarge
step 9
tape the BV power cable to the stiff wire and pull it back through
Click image to enlarge
I added sticky back foam to stop any small knocking noises
Click image to enlarge
step 9
feed the wire down to the mirror (you can just pull the roof lining down near the glass with your hand)
Click image to enlarge
step 10
Feed the wire behind the airbag in the pillar (I stuck it behind with the foam)
Click image to enlarge
step 11
The lower plastic cover near the glove box pulls off. You can see the plastic clip in this photo. Continue feeding the wire here (with foam again)
Click image to enlarge
step 12
When you feed the wire all the way down you can sneak it into the fuse box area through here.
Click image to enlarge
step 13
Trim the positive wire and attach pre prepared fuse
Click image to enlarge
step 14
This finally will go into unused fuse number 41 (this is unused on mine so no need to piggy back) this is a perm live unaffected by ignition cycle) sorry photo isn't too clear
Click image to enlarge
step 15
I mounted the BV here it is out of my line of vision and not obvious from the outside
Click image to enlarge
I earthed as per other posts on the glove box mounting screws (no photo as my phone camera button snapped off when taking the last photo...new phone soon then.)
Pop everything back and Ta da! all done
WARNING I will post the following on another post for those who wont read a BV thread
when you open your glovebox fully to reveal the fuses DO NOT CLOSE THE CAR DOOR
the door pocked hits the lid of the lover glove box and....
Click image to enlarge
one superglue fix to do...
amendment
I have had a friend whos blackvue wire shorted near the unit and proceded to melt the wires. the 5 amp fuse did not blow..I suggest a quick blow fuse.Also wthe use of a glassfibre silicone sleeve over the cable for safety.It is better to have and not need it then need and not have it.
Last edited by amazing on 25th Jun 2013 10:13 am. Edited 1 time in total
26th Sep 2011 3:18 am
row_perfect
Member Since: 01 Jan 2011
Location: Kent
Posts: 291
Great writeup and photos, thanks!D4 HSE, Active Rear Diff, surround cameras, adaptive xenons, heated steering wheel, TPMS, remote park heating, centre console cooler box
Club MT/R
Club RLD spare wheel protector
Club Sump plate & tree slider
Club Blackvue HD
26th Sep 2011 3:52 am
Hairy Dan
Member Since: 19 Jan 2011
Location: Co. Durham
Posts: 12319
Brilliant Thanks for going to the effort of documenting your install
26th Sep 2011 6:14 am
devonchilliman
Member Since: 03 Nov 2008
Location: Devon
Posts: 5224
Member Since: 19 Jan 2011
Location: Co. Durham
Posts: 12319
Followed your instructions at the weekend to wire my camera lead into a permanent live, dead easy following the photos although I used an 'add a fuse' instead of butchering one Cheers Ian
--------------------
Club N.E.R.D.S
Kielder 4x4 Safari
Discoless
10th Oct 2011 11:43 am
DaveC
Member Since: 29 Sep 2009
Location: Wirral
Posts: 1033
Dan
just did a search for the add a fuse and ebay has lots, any idea which size i would need for the disco?
any links to where you purchased would also be helpful
DavidXC90 T8 R Design Pro
MY14 D4 HSE Lux (sadly gone)
Mariana Black with Ivory interior and lots of toys!
13th Oct 2011 2:08 pm
Hairy Dan
Member Since: 19 Jan 2011
Location: Co. Durham
Posts: 12319
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
