On my D3, all four wheel nuts on the near side rear are slightly longer than all the nuts on the other wheels. They are long enough to stand slightly prowd of the allow wheel and therefore are difficult to tighten up properly.
I guess the longer nuts are for a 18" wheel, as they are too long for both the 19" and 17" alloys I have. Or maybe one person on the production line had a different batch.
I'll have to ask the dealer to get in a set of normal length bolts for me. Has anyone else noticed this with theirs?
Below is a photo which shows the length compared to the other nuts.
Matt
Lefthand one looks to wrong, mine are the same as the righthand one and are the right fit for 17", 18" & 19" LR rimsThe End
4th Sep 2006 1:45 pm
al cope
Member Since: 08 Nov 2005
Location: Oldbury, WM
Posts: 10297
So are you saying that they bottom out before tightening?
Also, as the section from the flat washer to the outside of the nut is the same, how can they stand proud.
I know the L322 RR used different wheel nuts pre and post 2002 (same thread though - and the early ones were black).
AlanVolvo XC90 B5 Plus Dark
Gone - MY18 D5 HSE - Corris on 22's with Black Pack
Now gone - MY16 D4 SE Tech, Loire Blue, Almond Leather, Privacy, plus some other goodies.
Old - MY12 D4 SDV6 XS Auto - Ipanema Sand with Almond Leather - Plus other niceties, and D4.com sticker
Older - D3 TDV6 XS Auto - Lugano Teal with Almond Leather, 20" Stormers, Shiny Tailpipes, DVD/TV - and obligatory D3 sticker
Ancient - D3 TDV6 S - Tonga with Ebony, 20" Stormers, satnav & DVD
Don't know why I've got four of these long ones then.
I've just spoken to the dealer and they are ordering in some more for me. My car now goes in tomorrow for it's enhancements too.Matt
4th Sep 2006 2:29 pm
bluebarchetta
Member Since: 25 Oct 2005
Location: Aylesbury
Posts: 524
Matt,
Is that Hartwells - were you getting it done whilst other things are being done or is it a special trip?
bb
4th Sep 2006 7:29 pm
CarlW
Member Since: 07 Aug 2005
Location: Lancashire
Posts: 111
Just looking at the photo (haven't had my wheel nuts off) my guess is that they are made in at two pieces and the one on the left has been overtightened and the centre part with the internal thread has pulled through. I'd be very reluctant to drive on those on the left!
CarlDisco 4 Landmark
Mercedes Benz SLK CDi
BMW 335D Touring
Defender XS SW 2010 - gone
TDV8 2008 RRS - gone
Disco 3 HSE 2005 - gone
BMW R1150GS
4th Sep 2006 10:18 pm
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26701
I think you could be correct there That does indeed look like the bolt is separating. I'm off to check mine now.
Matt,Is that Hartwells - were you getting it done whilst other things are being done or is it a special trip?bb
Yes, it is Hartwells. I phoned them today to ask them to order in some new wheel nuts for me (and I emailed this photo). Then asked if it needed the recent 'enhancements' which they replied yes. They then said they could do it tomorrow, if I didn't need a car. So I'm taking it in for the enhancements and a couple of other niggles (eg. dipped beam too low, juddering wipers).Matt
So are you saying that they bottom out before tightening?
Also, as the section from the flat washer to the outside of the nut is the same, how can they stand proud.
I know the L322 RR used different wheel nuts pre and post 2002 (same thread though - and the early ones were black).
Alan
Yes, the nuts are too deep so are proud inside - i.e. bottom out. This is why the top (end of thread) looks slightly rough cos they are being screwed against the hub.Matt
Just looking at the photo (haven't had my wheel nuts off) my guess is that they are made in at two pieces and the one on the left has been overtightened and the centre part with the internal thread has pulled through. I'd be very reluctant to drive on those on the left!
Carl
I know what you're saying, but I don't think it is. They are simply a longer nut.Matt
5th Sep 2006 12:43 am
dylansdad
Member Since: 04 Apr 2006
Location: Solihull
Posts: 745
so have you noticed any knocking recently as your wheel is wobbling? 2004 TDV6 HSE Auto Zambezi Silver
I've done the wheel in question up as tight as I can and it is tight enough - just. However, the ends of the nuts are getting chewed up.Matt
5th Sep 2006 12:59 am
DN D3 Decade
Member Since: 24 Jun 2006
Location: W.London.
Posts: 2294
Matt, this sounds bl**dy dodgy to me, i'd have a good look at your wheel and hub for any damage if poss before dealer gets to it, if the nuts have been bottomed out, and the wheel has been rattling about. If so,and things are damaged, get them to replace these as well as getting the right nuts. You are lucky this hasn't caused you a pile up, or worse!
I have recently decided to change my 4 locking wheelnuts for normal nuts, after my friend overtightened(?) his locking nut and broke the wheel spanner key - then found that different D3's have different keys - so mine didn't fit on his locking nut. Fortunately we don't have many thieves in this area looking for 18'' rims!
5th Sep 2006 9:35 pm
dylansdad
Member Since: 04 Apr 2006
Location: Solihull
Posts: 745
note some of the origional locking keys were defective and need replacing your friends might be one of them and so its failure wasnt his fault. possible he could get it replaced free.2004 TDV6 HSE Auto Zambezi Silver
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
That does indeed look like the bolt is separating. I'm off to check mine now.
