Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Technical (D3)

Weak windscreen washer jets
Post Reply  Down to end
Page 1 of 2 12>
CY
 


Member Since: 16 Aug 2005
Location: Warwickshire
Posts: 4506

Scotland 2008 Discovery 3 TDV6 HSE Auto Tangiers OrangeDiscovery 3
Weak windscreen washer jets

Haven't been able to find a thread on this particular problem...

My windscreen washer jets seem to be getting weaker. Each one seems to trickle out a very faint stream of water which barely reaches the top of the windscreen with any might. They also don't appear to be shooting out of both nozzles - just one on each jet. So in total I got two measly streaks of water.

The headlamp jets and rear window jets seem to be working as normal.

Is there a central pump or should buying a set of new LR049290 washer jets do the trick?

Thanks,
Chris
 2007 Porsche Boxster (987) 2.7
2008 Discovery 3 TDV6 HSE G4 Challenge (1 of 68)
2023 Defender 90 D250 X-Dynamic HSE 
 
Post #200993417th Dec 2018 7:43 am
View user's profile Send private message View poster's gallery Reply with quote
geoffsnook
 


Member Since: 13 Jun 2014
Location: south wales
Posts: 3170

Wales 

It may be the jet's need a clean with an airline or a pin as they may be blocked or the line may need cleaning Thumbs Up
 Discovery 3 se gone
Range rover sport supercharged here:) 
 
Post #200994217th Dec 2018 8:14 am
View user's profile Send private message View poster's gallery Reply with quote
Globetrotter448
 


Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1817

Australia 2007 Discovery 3 4.0 V6 Petrol SE Auto Java BlackDiscovery 3

The windscreen washers have their own pump. Check that the nozzles are not blocked by inserting a needle or straightened paper clip, then check that you do not have a kink in the feed pipe. Embarassed
  
Post #200994317th Dec 2018 8:15 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10674

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

you can also remove the small pump from the tank.

Then remove the grommet from tank and clean the filter in the grommet.
  
Post #201002817th Dec 2018 12:14 pm
View user's profile Send private message View poster's gallery Reply with quote
Corris MacGray
 


Member Since: 23 Aug 2017
Location: OutofTown
Posts: 55

England 2016 Discovery 4 3.0 TDV6 Commercial Auto Corris GreyDiscovery 4

Doesn't it get like this when you're over 60? Embarassed
  
Post #201022917th Dec 2018 8:16 pm
View user's profile Send private message View poster's gallery Reply with quote
gvmnt
 


Member Since: 06 May 2007
Location: Cambridge
Posts: 40


Globetrotter448 wrote:
The windscreen washers have their own pump. Check that the nozzles are not blocked by inserting a needle or straightened paper clip, then check that you do not have a kink in the feed pipe. Embarassed


hi - i'm struggling for too long now with my windscreen washers ... replaced the front/headlamp pump, the nozzles, the valves, but it's still with barely any fluid coming out. i'm now of the opinion that there is a kink somewhere in the feed pipe to the windscreen, but it seems that the water pipe runs in the same loom as the electrical wires. it's hard to think that the kink would be somehow in the loom, but i also don't see it anywhere else.

the rear window washer - which i know has it's own pump and line - works absolutely as expected.

i see a number of comments on cleaning plugged up parts, all of which i have done - but do not seem to find anyone commenting on a kinked pipe. i would be grateful if any experience can be shared please.
  
Post #237778920th Sep 2024 2:54 pm
View user's profile Send private message View poster's gallery Reply with quote
G7jtk
 


Member Since: 03 Jun 2014
Location: Prudhoe
Posts: 861

England 2007 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3

Change them for jets with a fan pattern. Way better
 

Last edited by G7jtk on 22nd Sep 2024 12:32 pm. Edited 2 times in total 
Post #237782220th Sep 2024 10:42 pm
View user's profile Send private message View poster's gallery Reply with quote
gvmnt
 


Member Since: 06 May 2007
Location: Cambridge
Posts: 40


G7jtk wrote:
Chand them for jets with a fam pattern. Way better


any suggestions on where i can get the fan pattern? part number, etc? many thanks
  
Post #237789222nd Sep 2024 11:20 am
View user's profile Send private message View poster's gallery Reply with quote
gstuart
 


Member Since: 21 Oct 2016
Location: kent
Posts: 14128

United Kingdom 2005 Discovery 3 TDV6 Base 7 Seat Auto Java BlackDiscovery 3

Know when I upgraded my d3 windscreen washer to heated d4 ones I disconnected the pipes both ends from the washer bottle and at the windscreen area and put an air line through it

Full of junk and sorted it out , those none return valves can also block up

Sorry that’s not much help but others can recommend the fan pattern jets for u
   
Post #237789922nd Sep 2024 11:53 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10674

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

Is the one way valve in the bonnet ? right next to the jets ?
  
Post #237790322nd Sep 2024 12:13 pm
View user's profile Send private message View poster's gallery Reply with quote
gstuart
 


Member Since: 21 Oct 2016
Location: kent
Posts: 14128

United Kingdom 2005 Discovery 3 TDV6 Base 7 Seat Auto Java BlackDiscovery 3

Yes mate , one NRV on each jet , this was before I added the heated D4 jets


Click image to enlarge


Click image to enlarge
   
Post #237790722nd Sep 2024 12:28 pm
View user's profile Send private message View poster's gallery Reply with quote
G7jtk
 


Member Since: 03 Jun 2014
Location: Prudhoe
Posts: 861

England 2007 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3

gvmnt wrote:
G7jtk wrote:
Chand them for jets with a fam pattern. Way better


any suggestions on where i can get the fan pattern? part number, etc? many thanks


These are what I fitted. Had to make wedge shims up to hit the windscreen and lost the heater elements.
They work way better than the originals but could be better.

https://www.ebay.co.uk/itm/133454438114
 

Last edited by G7jtk on 22nd Sep 2024 2:56 pm. Edited 1 time in total 
Post #237790822nd Sep 2024 12:31 pm
View user's profile Send private message View poster's gallery Reply with quote
gvmnt
 


Member Since: 06 May 2007
Location: Cambridge
Posts: 40


gstuart wrote:
Know when I upgraded my d3 windscreen washer to heated d4 ones I disconnected the pipes both ends from the washer bottle and at the windscreen area and put an air line through it

Full of junk and sorted it out , those none return valves can also block up

Sorry that’s not much help but others can recommend the fan pattern jets for u


yeah - i don't have an air supply so tried to do the same with the bicycle pump and the beach ball nozzle. there is definitely much more resistance in the water line than i feel there should be. the bicycle pump does go up to 60psi and let's air through but not enough "volume flow" to push through what might be there. at my wits end Big Cry
  
Post #237790922nd Sep 2024 12:35 pm
View user's profile Send private message View poster's gallery Reply with quote
gstuart
 


Member Since: 21 Oct 2016
Location: kent
Posts: 14128

United Kingdom 2005 Discovery 3 TDV6 Base 7 Seat Auto Java BlackDiscovery 3

Have u tried it by pulling the NRV’s under the bonnet off plse to see if the pipe is clear

Then blowing through each non return valve to ensure there also clear as when I done mine they had junk inside

Along with ensuring the jets are clear, I just got some spare hose to attach it, or other way to use a nozzle fitting on the end of ur hand pipe

Hope that helps
   
Post #237791022nd Sep 2024 12:39 pm
View user's profile Send private message View poster's gallery Reply with quote
gvmnt
 


Member Since: 06 May 2007
Location: Cambridge
Posts: 40


thanks for the pointers. played with the vehicle today once again ... it does all point to a pinch / kink somewhere in the feed-pipe/water-line to the windscreen ... i bypassed it with a hose and everything worked like magic ... so at least i know where the culprit sits.

any suggestions for where the factory hose runs? it goes into a wiring loom pretty soon above the windscreen pump and i lose sight of it until it comes out at the corner of the bonnet. i suspect most of it goes behind the fender / wheel arch. might need to accept the bypass solution as the permanent one Sad

any ideas and suggestions are welcome
  
Post #237845229th Sep 2024 3:24 pm
View user's profile Send private message View poster's gallery Reply with quote
Display posts from the last:  
Post Reply Back to top
Page 1 of 2 12>
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site