Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
DISCO3.CO.UK > Technical (D3)

Sudden engine stop, crankshaft position sensor?
Post Reply  Down to end
Page 1 of 1
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 
Sudden engine stop, crankshaft position sensor?

Big scare yesterday: after 220 km of motorway and roads without problem I passed a mountain pass with quite a few bends and at the exit of the pass in a straight line going downhill suddenly the engine stopped.
I managed to park on the side
On the Dashboard :
HDC not available message ,F signal on and orange suspension light.

I tried to restart, the engine running but it won't start
I was still 60 km from my destination with my dog ​​and a lot of luggage

I turn everything off and wait 5 minutes but it doesn't restart...

Luckily I had my gap odb tool
And I see the following faults :

Body Control
* B1B02-28 (2F) Low frequency coil - General signal failure - signal bias level is out of range/zero adjustment failure
( at 195340 km )
* B1C57-14 (6C) Passive start ignition relay coil circuit - General electrical failure - circuit short to ground or open
( at 195340 km )
* B1D12-15 (2E) Volumetric alarm power circuit - General electrical failure - circuit short to battery or open
( at 195340 km )
* U0155-87 (28) LCD Gauge Communication Lost - Bus signal/message failure - missing a message
( at 195340 km )
Engine TDV6
* P0336-00 (6C) Crankshaft position sensor A circuit range/performance
Instrument Pack
* U0102-87 (28) Lost communication with transfer case control module - Bus signal/message failure - missing a message
* U0132-87 (28) Lost communication with ride level control module - Bus signal/message failure - missing a message
Parking Brake
* U0101-87 (EB) Lost communication with transmission control module - Bus signal/message failure - missing a message
( at 197840 km )
* U0100-87 (EB) Lost communication with engine control module/powertrain control module 'A' - Bus signal/message failure - missing a message
( at 197840 km )
Suspension
* C1A35-01 (2E) Reservoir valve - General failure information - general electrical failure
( at 195340 km )
Transmission
* U0401-86 (AF) Invalid data received from engine control module/powertrain control module - Bus signal/message failure - signal is invalid
( at 197840 km )
Vehicle Dynamic
* U0402-68 (08) Invalid data received from transmission control module - Algorithm based failure - event information
( at 195778 km )
* U0401-68 (0B) Invalid data received from engine control module/powertrain control module - Algorithm based failure - event information
( at 197840 km )

I cleared the faults and was able to restart and do 60 km without problem


Now I'm worried, where did this come from and can it happen again?

The error code that bothers me the most is:
Engine TDV6
* P0336-00 (6C) Crankshaft position sensor A circuit range/performance

Thank you for your advice and experiences


Nick
  
Post #23744994th Aug 2024 6:42 am
View user's profile Send private message View poster's gallery Reply with quote
Globetrotter448
 


Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1812

Australia 2007 Discovery 3 4.0 V6 Petrol SE Auto Java BlackDiscovery 3

Possible loose battery or earth wire. Some vehicles had the positive wire to the starter motor rub on the front diff.
  
Post #23745224th Aug 2024 10:14 am
View user's profile Send private message View poster's gallery Reply with quote
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 

THANKS,
I'll try to take a look at it
Could this cause a Crankshaft position sensor fault?
  
Post #23745254th Aug 2024 11:09 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10672

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

Crankshaft position sensor does seam most likely. I think they tend to fail when hot

Not a nice sensor to change though. But I guess it maybe worth purchasing one
  
Post #23745334th Aug 2024 1:08 pm
View user's profile Send private message View poster's gallery Reply with quote
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 

THANKS PETE
no, it doesn't look easy to replace.
Is there any simple solution to test it?
what is surprising is that by clearing the fault I was able to restart and drive for 60 km…
  
Post #23745424th Aug 2024 2:53 pm
View user's profile Send private message View poster's gallery Reply with quote
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 

I checked the battery and the starter wiring which do not seem to be the cause.

I read a lot of posts about replacing the CKP
it seems that this can be done without removing the gearbox

but it's not simple

how to eliminate other possible causes before embarking on this adventure?
Since I cleared the faults, none reappeared and the engine started very well



That said, I'm a little afraid of riding too far…
  
Post #23746205th Aug 2024 3:34 pm
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10672

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

With diagnostic tool eg gap IID or ap200 you can read the crank sensor speed with engine running.
Do it now while you can.

Then in the fault returns, see if it’s 0 while cranking.
Also check it while cranking when it’s working
  
Post #23746225th Aug 2024 3:47 pm
View user's profile Send private message View poster's gallery Reply with quote
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 

Thanks again Pete for your help.

when starting I saw 100 once and the next time 140 rpm
but hey it's very fast because the engine starts immediately

once started the engine oscillates between 740 and 760 rpm

while driving I did not notice any specific variation

What conclusions can I draw from this?
  
Post #23746546th Aug 2024 8:47 am
View user's profile Send private message View poster's gallery Reply with quote
Pete K
 


Member Since: 15 Jan 2016
Location: GL
Posts: 10672

England 2005 Discovery 3 TDV6 HSE Auto Rimini RedDiscovery 3

Well now you know that the GAP IID tool crank live values works. (not all of them do)
So next time it won't start, you can repeat the exercise and see if it reads 0 while cranking. That would confirm it.

The exact value you get while cranking will depend on battery level and engine temperature etc.
As long as it's not reading zero, that is good.

You could also check the cam shaft speed. Save both live values to your favourites.

Cam speed should be half the crank speed.

Other things you could do if you wanted.

1) Inspect the crank sensor connector, to ensure pins clean etc. and familarise yourself with its location.

Click for connector picture and other info
https://www.disco3.co.uk/forum/topic206795...p;start=30


2) purchase a crank sensor and keep it in the car, so a garage can fit it if you break down

Try a citroen or pegeuot garage if you live in france, as they use the same engine.
  
Post #23746576th Aug 2024 9:06 am
View user's profile Send private message View poster's gallery Reply with quote
NTG
 


Member Since: 22 Oct 2022
Location: GAP
Posts: 34

France 

Tath's what I am going to do !

Thanks again Pete
  
Post #23747688th Aug 2024 6:15 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site