Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
last questionđź‘€
Are the push fit connectors all the same for the central front and rear valve blocks?
after all this information I am ready and I will keep you informed
21st Jan 2024 12:46 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
Hi
Sorry I should have quoted it better , as on my new front struts I removed the Voss connectors and fitted them with the new pushfits
Yes all 3 x valve blocks are the same size being 6mm , great u have the plastic cutter
Hope that helps and indeed plse let us know how u get on , hopefully it’s all straight forward and mange to stay warm in this horrible windy weather
Last edited by gstuart on 22nd Jan 2024 3:11 am. Edited 3 times in total
22nd Jan 2024 3:06 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
NC500 wrote:
Another photo showing part of the routing
Click image to enlarge
Also wished to say many thks for sharing that pic as wasn’t 100% sure of the route , assumed it ran across the bottom chassis rail but see it runs on the top
Many thks once again as So handy to know for the future
22nd Jan 2024 3:09 am
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
Hello... Thank you again for these insights...
Regarding the push fit connector which is on the air spring, is it straight or angled? (I think it's right!)
I put some elbows in but it leaks at the entrance to the pipe.. I was thinking of putting Voss connectors back in for that.. Thank you and have a nice day
Philip
22nd Jan 2024 7:33 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
Ur so welcome , they were straight connectors
Ref the pushfits do they have plastic collars to them or did u get ones from the link of the ones I got plse
Must confess didn’t have any issues with the ones I got , however if ur having issues would refit the Voss ones on ur struts ,particularly as the whole strut has to come out every time , maybe the ends of the pipes have some scoring on them or out of shape , or bad pushfits
Hope that helps
Click image to enlarge
22nd Jan 2024 10:06 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
Good evening
The connectors have plastic collars.. I think the problem comes from this plastic collar
22nd Jan 2024 11:35 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
Many thks for the update , alas from previous experience found those plastic ones can often leak , due to there lower pressure ratings
the brass ones have a pressure rating of 80 bar where the plastic will often only have a 10 bar rating
That was the main reason I picked the brass ones as the air compressors can produce between 13 to 17 bar therefore exceeding the plastic collar fittings
Was also careful buying the correctly rated plastic pipe seeing the air suspension compressor can produce roughly between 189 psi / 13 bar to 260 Psi or 18
When I was shopping for a roll of plastic pipe some were only rated at 250 psi so too close for comfort , tube I got was rated around 400 psi , advertised having a wall thickness of 4mm
Hope that’s also useful to ur good self
23rd Jan 2024 4:38 am
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
bonsoir
ca y est..les tuyaux avant ont ete changes ainsi que les raccord...jai remis les raccords voss ..pour l'arriere je nai pas de fuites car teste avec de l eau savonneuse mais les raccords sont coudes et colliers en plastique
je pense les changer a l avenir car il y a encore une legere fuite..le disco perd quelques cm en une nuit j ai regarde au niveau electrovanne centrale car jai mis des raccords push fit en metal et pas de fuites
Merci encore pour l’aide
Philippe
28th Jan 2024 7:06 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
hi gstuart
another question when i choose build mode with iidtool about 12 hours approxymatly the rear loose few centimeter
it s look like a leak from the rear?
thank s
Philippe
4th Feb 2024 11:02 am
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
Hi
To rule a leak out u could always remove the gap iid then test it overnight by measuring the heights first then removing fuse F26 to see what it’s like the next day
At least then ur be able to rule any leaks out
Hope that helps
4th Feb 2024 12:13 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
Thanks...
But it s not the same thing(remove fuse 26) when I choose build mode with my iidtool?
4th Feb 2024 12:33 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 13877
Sorry as re read it, so basically after you’ve taken the gap iid tool out the rear drops after 12 x hours
Personally mine will drop around 10mm after 24 x hours , found no leak and just put it down to it settling as it won’t drop any further than that
Would at least first measure the heights before and after the gap iid tool has been removed, ur then get an accurate reading
Hopefully someone else may be able to help further if that’s also happened to them
4th Feb 2024 12:58 pm
kineland
Member Since: 15 Jul 2014
Location: cavaillon
Posts: 187
Thank s for u response
At this Time the rear shut down about 7 centimeter !
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum