Member Since: 22 Nov 2018
Location: Akershus
Posts: 19
Paddle shift on D3 with D4 steering wheel
Hi guys,
i just wanted to share how i "enabled/added" paddleshift on my D3 with a D4 steering wheel. I got the Fritjof Dittner PCB's in my D4 steering wheel.
Click image to enlarge
Edit: I will add some information and clean up the description later
On the connector C2658 on the gear selector you can see pin 5 and 6 is shift up/down in SPORT/MANUAL mode.
I made a loom for easy testing of gear shifting:
Pin 5(yellow/upshift) and 6(brown/downshift)
De-pinned and made a loom with gear up/down and 12V and GND. You dont need 12V/GND in this loom, but was convinient for testing.
I did remove isolation from the wires about 7cm from the pin, and soldered wires and crimped a JST connector at the end.
After some testing i found that the signals are pulled high in the TCM, and with a 100Ω resistor i could pull the signal to ground and make the gear shifting.
The paddles on the D4 steering wheel is 2.7KΩ when open circuit and 560Ω when paddle is pressed. So i had to remove two resistors(2,2KΩ marked 222 and 560Ω marked 561) and solder in a 100Ω resistor(replaced with the 560Ω resistor and the 2,2KΩ is removed) in each paddle.
De-pin hinge and remove PCB. A norwegian KRONE as reference would not do you guys any good, but there is very small resistors
Because i have the Fritjof Dittner PCB's in my D4 steering wheel, there is no signals from or to the paddleshifter. Just 12V and GND for the LED. I have installed the D4 clock spring which got beefier connector for heating, so i removed pin 3(black/GND) and pin 7(purple/12V) from the 8 pin connector from the steering wheel loom, to the clock spring. I now have spare pins in my connector for up/down signal. Pin 8 was never used, so i went for pin 7 and 8. This signals are routed from the car side of the clock spring to the 4 pin(should be 2pin) connector i spliced from the gear selector.
New clock spring with 3 connectors:
De-pinned pin 7 on the "car side" of the clock spring and inserted pins for the gear up/down signals(pin 7 and 8) which are routed to the new loom from the gear selector.
The power comes through this plug now:
New wiring loom in the steering wheel, pin 7 and 8 on the white connector are now the up/down signals:
Pin 2 and 3 on the 4 pin connector for the paddleshift on the Fritjof Dittner PCB er de-pinned and signals are routed directly to the 8 pin connector instead.
Last edited by Jan R. on 21st Aug 2023 1:09 pm. Edited 5 times in total
20th Aug 2023 8:38 pm
darrind
Member Since: 04 Jul 2008
Location: In A World of My Own!
Posts: 2908
Looks good Must stop buying shiny toys....
20th Aug 2023 8:49 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10742
Nice info
Does the selector need to be in sport/manual for them to work ?
20th Aug 2023 8:52 pm
Jan R.
Member Since: 22 Nov 2018
Location: Akershus
Posts: 19
Pete K wrote:
Nice info
Does the selector need to be in sport/manual for them to work ?
Yes, it needs to be in SPORT/MANUAL mode for them to work.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
