V8man
Member Since: 01 Jan 2021
Location: Dunno i was just following the satnav😳
Posts: 288
![](templates/vbnew/images/spacer.gif)
![2007 Discovery 3 4.4 V8 HSE Auto Cairns Blue 2007 Discovery 3 4.4 V8 HSE Auto Cairns Blue](../images/veh/cairns_blue.gif)
|
Suspension calibration cautionionary note |
|
Hello all,
Firstly apologies in advance if this is covered elsewhere.
Just a cautionary tale regarding calibration of eas.
I have had my vehicle for approx 3 years and when measuring the suspension heights front n/s was always 15 ish mm low regardless of how level the ground was when parked up, so i decided on Saturday to take the plunge and calibrate suspension even though i have had no other issues with it.
Yesterday i went for a drive and suspension warning light came on , dropped height to floor and warning in dash.
Now i was a bit shocked because i had used the "guided method " and was very careful with measurements.
So why the issues? Well, when i re attempted the calibration i took the i pad to each wheel with me instead of going back to the bench to click "next" and it turns out the rear suspension was lifting back up after i altered it so when on my original method i clicked "next" i was entering the wrong values without knowing. Consequently all the settings were and once i got to 70mph the S***t hit the fan!
So if you attempt this task keep your eye on each corner and dont click"next" unless your measurement is correct, if the car does alter it redo it and click next asap.
Now i know the experts on here dont need this advice but if you are new to the iid tool i hope this proves useful to you.
This could of course just be some wierd anomaly on my d3 and may not happen to anyone else.
Suffice to say the suspension is now ok .
All the best .
P.S. thanks to all those who have contributed to this site i have benefited greatly without the need for questions just the old search function i am very grateful to you all. 1996 Defender -died (now in landrover heaven😇)chassis to ashes , rust to dust !
2004 Defender td5 gone
2012 Evoque gone
2007 D3 V8 HSE
|
30th May 2023 12:33 pm |
|
|
bensla
Member Since: 02 May 2023
Location: Trowbridge
Posts: 141
![](templates/vbnew/images/spacer.gif)
![2008 Discovery 3 TDV6 HSE Auto Stornoway Grey 2008 Discovery 3 TDV6 HSE Auto Stornoway Grey](../images/veh/stornoway_grey.gif)
|
Sounds like a useful tip - thanks for sharing!
|
5th Jan 2024 3:53 pm |
|
|
Carl and Petra
Member Since: 13 Feb 2015
Location: Hautes Pyrenees
Posts: 219
![](templates/vbnew/images/spacer.gif)
![2015 Discovery 4 3.0 TDV6 SE Auto Sumatra Black 2015 Discovery 4 3.0 TDV6 SE Auto Sumatra Black](../images/veh/sumatra_black.gif)
|
Good post. Helpful to hear why things don’t go to plan.
|
5th Jan 2024 4:26 pm |
|
|
Disco carl
Member Since: 10 Nov 2023
Location: West Midlands
Posts: 13
![](templates/vbnew/images/spacer.gif)
![2006 Discovery 3 TDV6 S Manual Baltic Blue 2006 Discovery 3 TDV6 S Manual Baltic Blue](../images/veh/baltic_blue.gif)
|
Just to let people know I had this problem and the I carsoft lr v3 were easily capable of doing height calibration cheers
|
14th Jan 2024 10:17 am |
|
|
Worms
Member Since: 24 Sep 2023
Location: Highlands
Posts: 343
![](templates/vbnew/images/spacer.gif)
![2005 Discovery 3 TDV6 Base 7 Seat Auto Zambezi Silver 2005 Discovery 3 TDV6 Base 7 Seat Auto Zambezi Silver](../images/veh/zambezi_silver.gif)
|
Yes, useful info and thanks to Bensla for resurrecting the thread. Mine lets you finish the calibration before deciding that it would prefer to have one corner a bit higher. I suspect, though, that for those of us with this problem the issue is with the height sensor, rather than the IID tool itself. Previously:
2010 FL2 TD4e GS
‘93 Defender 110 200TDi CSW - still got this, non-runner on SORN.
‘87 Defender 90 4 cyl Petrol
‘83 110 CSW V8 - best ever!
Range Rover 2-door V8 (not sure of year - 4-speed box and vacuum diff switch)
Series III SWB Diesel
|
14th Jan 2024 12:20 pm |
|
|