So, when your iiD arrives, I'd recommend you:
1. Clear all faults
2. DO NOT ATTEMPT ANY CONFIG CHANGES, NO MATTER HOW TRIVIAL YOU THINK THEY ARE.
3. Drive around for a few days and check what codes have appeared..
Dean
====================================
2011 D4 XS - OBD port protection, RLD spare wheel protector, All LED interiors lights, Timed Climate enabled, iiD tool paired.
2011 D4 Landmark - Stolen from same dealer before I paid for it
2011 D4 GS - Stolen whilst at dealer ... All LED interiors lights, DRLs, Spare Wheel protector.
1996 300Tdi - Eaten by tin worms
21st Oct 2022 2:14 pm
cmb2020
Member Since: 08 Sep 2020
Location: Buckley, North Wales
Posts: 1150
Thanks..
I have a fair bit of knowledge on firmware and program settings on computers. So understand not to make a silly mistake of changing any settings without thinking twice.
I already have cleared the codes using an autel ap200. The bong happens as soon as I put it in 6th gear again. Then the epb about 30 seconds later.
Hoping this gap iid will be able to pinpoint with more precise codes or info!
Will come back with findings cheersDisco 3 SE Manual 2005 V6 2.7
Buckley, North Wales
21st Oct 2022 9:08 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10663
So if it happens the instant you put it in 6th. (and when stationary with engine on) it could be the sensor. A complete guess. have you seen one of these on the car ? don't know where. I would expect a fault code to point to it though.
If it happens after driving along, a while after selecting 6th, sounds like people blame the clutch
22nd Oct 2022 9:08 am
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6355
I would try xyz sensor reset procedure first before doing anything. also xyz sensor also goeas crazy in case of slipping clutch (driven accros europe once on slippingclutch always throwing error with XYZ sensor)
Greg
22nd Oct 2022 9:42 am
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4508
^ no Z ! Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
22nd Oct 2022 10:51 am
cmb2020
Member Since: 08 Sep 2020
Location: Buckley, North Wales
Posts: 1150
Thanks all
I wouldn’t have a clue where to start looking for that part Pete but I’ll look around gear box underneath tomorrow and try locate it. If I do I’ll get pictures etc.
The problem happens instantaneous. Immediately when I put in 6th. Says “E” on dash which I think I saw disco Mike say on another thread the E indicates it’s an electrical problem. Also praying it’s not clutch!
Gap iid still not arrived so giving up til Monday now I think
And as for the xy calibration I did try it but it won’t work once I hit 6th gear the warning triggers
Thanks as alwaysDisco 3 SE Manual 2005 V6 2.7
Buckley, North Wales
22nd Oct 2022 11:22 am
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4508
The XY sensor is right on the top of the gearbox, above the selector rods. I don't think it would be possible to change it without taking the gearbox out of the car.
I did a clutch recently, and it's not a 5 minute undertaking!Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
22nd Oct 2022 11:27 am
cmb2020
Member Since: 08 Sep 2020
Location: Buckley, North Wales
Posts: 1150
Indie seemed to be confident he could get to it and clean it for potential (metal dust) obstructing the furthest gear
TBC…Disco 3 SE Manual 2005 V6 2.7
Buckley, North Wales
22nd Oct 2022 11:31 am
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10663
I guess you need to look at live values (on GAP or maybe Autel) for the gearbox
It should tell you what gear you are in, (with ignition on).
If you run through the gears on the drive, and it goes 12345 Error (much like the dash does I guess) then that sensor needs calibration or replacement I would guess.
22nd Oct 2022 2:34 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4508
cmb2020 wrote:
Indie seemed to be confident he could get to it and clean it for potential (metal dust) obstructing the furthest gear
TBC…
Interested to see how that goes. Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
22nd Oct 2022 3:00 pm
cmb2020
Member Since: 08 Sep 2020
Location: Buckley, North Wales
Posts: 1150
Here you go guys:
Attached gap iid fault code saying Y sensor
Does this give any more of a clue as to where exactly I’m to look please?
Thanks
Disco 3 SE Manual 2005 V6 2.7
Buckley, North Wales
24th Oct 2022 6:05 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6355
do XY sensore recalibration pocedure
if that reappears take next step ..
24th Oct 2022 7:17 pm
cmb2020
Member Since: 08 Sep 2020
Location: Buckley, North Wales
Posts: 1150
I tried the recalibration procedure. When I put it in 6th the fault comes up and won’t allow the completion of calibration
Next step being? Oil change maybe? Or gap iid live values of the module?
I’m new to the gap iid so no clue how to navigateDisco 3 SE Manual 2005 V6 2.7
Buckley, North Wales
24th Oct 2022 7:51 pm
rrhool
Member Since: 28 Aug 2014
Location: Norfolk
Posts: 4508
My gut feeling is that you're not going to fix it remotely. I think you're going to have to change the sensor.Richard
D3 SE 2007. Triumph 2.5Pi 1973. Ferguson TEA20 1948.
Discovery 2 4.0 ES 2001- Gone
Discovery 1 300Tdi ES '95 - Gone
Range Rover Classic '79 - Gone
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
... All LED interiors lights, DRLs, Spare Wheel protector.
