Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
Jammed Oil Filter Cover
All my own fault...
Would really appreciate any suggestions.
So I was tightening the oil filter cover after a filter change.
I used a NEW torque wrentch set to 25Nm.
As the words 'This is too tight' went through my mind...
I sheared off the cover top nut.
I tried a strap wrench and it broke...
I tried a 3 leg wrench and that broke...
What are my options..?
And yeah I feel so stupid!
Any thoughts would really be appreciated.
Cheers.
17th Nov 2021 1:09 pm
Breg90
Member Since: 04 Feb 2017
Location: Falkirk
Posts: 360
U need to grip the outside of the housing in a uniform manner to reduce point stress. How about a strip of thin steel shim (say 0.25mm thick), form it into an over lapping tube (two layers thick) over something like an aerosol can), place over oil filter cap. Secure with 3 jubilee clips to get a good grip. Make sure wrap if shim is tall enough to protrude up well beyond cap. Cross drill it in two places so you can fit a bar across. Then use bar to undo?Series one 1949 - in bits, chassis is strapped to the ceiling in my garage (beside the canoe)
LR 90 - In bits
Disco 3 - currently in bits
17th Nov 2021 1:34 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5044
Are those tools made of cheese?
You could try putting some rope through the strap tool and see if that will get it. A sheet of sand paper doubled and wrapped around the filter housing will aid grip. Alternatively get a filter wrench but be patient, you don't want to shatter it!yµ (idµ - eAµ) ψ=mψ
17th Nov 2021 1:37 pm
natvegas
Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
Thanks guys.
Will try out the rope idea first.
I have orderd some steel shim and will try that Sunday.
I guess the worst scenario is breaking it up and digging it out...
Has anyone ever done that before..?
Bit worried about debris dropping into the oil supply.
Will let you know how it goes!
17th Nov 2021 4:14 pm
Pete K
Member Since: 15 Jan 2016
Location: GL
Posts: 10684
for future reference, you just need to tighten it, till it stops turning
17th Nov 2021 7:11 pm
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
What type of torque wrench were you using ? Some only work to the selected torque in one direction.
These torque wrenches usually have an arrow pointing which way they work and the square part the socket fits on can be pushed through to the other side so you can use it in the other direction.
I have seen many snapped wheel nuts were somebody has got it wrong using this type of torque wrench.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
17th Nov 2021 7:19 pm
M3DPO
Member Since: 22 Sep 2010
Location: Notts.
Posts: 8230
Find a piece of nylon rope the type used on mower pull starts, double it up and wrap it round the cap anti-clockwise until you have a small loop to push a lever through, it should grip sufficiently to undo it. Good luck
Hand tight is almost enough to tighten the cap as it is the O ring that makes the seal not the thread.
It can when others can't,
It will when others won't,
It goes where others don't.
17th Nov 2021 8:51 pm
jenseneverest
Member Since: 12 Jun 2017
Location: somewhere
Posts: 769
Member Since: 23 Dec 2013
Location: under the car
Posts: 404
I would try the wrench which tightens the disks of the angle grinder.
Drill 2 holes acc. to pattern of wrench into the housing. Extend the wrench bottom to have a greater leverage.Achim
own garage certified LR tech
Disco 2 TD5 MY 2001 - gone but still driven by another owner
Defender 110 TD5 driving me bananas with all faults
Disco 3 TDV 6 HSE MY 2005 gone @280.000 km
Disco 4 SDV 6 HSE MY 2012
18th Nov 2021 7:52 am
natvegas
Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
aja4x4 wrote:
What type of torque wrench were you using ? Some only work to the selected torque in one direction.
These torque wrenches usually have an arrow pointing which way they work and the square part the socket fits on can be pushed through to the other side so you can use it in the other direction.
I have seen many snapped wheel nuts were somebody has got it wrong using this type of torque wrench.
Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
M3DPO wrote:
Find a piece of nylon rope the type used on mower pull starts, double it up and wrap it round the cap anti-clockwise until you have a small loop to push a lever through, it should grip sufficiently to undo it. Good luck
Hand tight is almost enough to tighten the cap as it is the O ring that makes the seal not the thread.
Right I have sourced some starter rope will give it a go.
18th Nov 2021 3:33 pm
natvegas
Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
Member Since: 01 Nov 2021
Location: Somerset
Posts: 9
disco4ever wrote:
I would try the wrench which tightens the disks of the angle grinder.
Drill 2 holes acc. to pattern of wrench into the housing. Extend the wrench bottom to have a greater leverage.
Thanks. Will try this on Sunday.
18th Nov 2021 3:34 pm
G3Z
Member Since: 16 Dec 2018
Location: South Wales
Posts: 559
I’d be drilling a hole through the filter housing and getting a long screwdriver to pass though it and allow you to twist it off. Obviously this will mean a new filter and cleaning the housing out thoroughly.Defender 110 2.4 TDCi Utility Station Wagon.
2007 Disco 3 GS TDV6 Manual
200,000+ mile club 😎
18th Nov 2021 4:52 pm
OvalAutos
Member Since: 28 Dec 2018
Location: Cradley Heath
Posts: 382
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
