Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
TDV6 injectors
Hi!
Have a D4, 2.7l TDV6 from 2010 with 170t km (105t mls).
The engine runs well, but you can hear it nail when idling. The typical diesel nailing.
But too loud for this engine for my taste.
Should the injectors be worn out after this running time?
I would then like to swap all six at once, where can I get them cheaply?
Are there any repaired in exchange?
Regards,
Thomas
3rd Dec 2021 6:35 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5069
Unlikely they're worn after such small mileage. If you have diagnostic tool post the trim balance levels for all six injectors, and any fault codes for the ECM.yµ (idµ - eAµ) ψ=mψ
3rd Dec 2021 7:12 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
have a IID - will post it soon
3rd Dec 2021 8:06 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
Okay - this weekend the engine sound better IMHO.
Have checked values with IID an have made a little video (how can I upload the video here)?
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
Hi
Hope u don’t mind me mentioning but ur battery needs a good overnight charge , should be around 12.6 Vdc with the engine off , 14.6 Vdc running . U codes can normally be ignored and cleared
Prof g will be able to guide u considerably better than myself with regards to the injectors
Hope that helps a little
9th Dec 2021 10:16 am
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5069
Injectors are fine, clear the codes and give her a good hard run and read the codes again.
Sounds OK to me so just enjoy it, when something is wrong she won't be long about telling you. yµ (idµ - eAµ) ψ=mψ
9th Dec 2021 12:49 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
The U-Codes are comming again - I have alreday cleared it repeated.
Most is lost comm wirth transmission control modul or parking assist control modul.
In the near future I will check the contacts of the connectors on the ECU and the other modules.
Thanks for the Information about the injectors.
9th Dec 2021 2:35 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5069
Check the contacts at the TCM (water ingress) and possibly the mechatronic plug on the transmission for corrosion. yµ (idµ - eAµ) ψ=mψ
9th Dec 2021 3:05 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
Yes - exact - that I'll do.
9th Dec 2021 3:07 pm
gstuart
Member Since: 21 Oct 2016
Location: kent
Posts: 14177
Hi Thomas
Plse let us know how u get on and ur battery is all ok after an overnight charge
9th Dec 2021 4:19 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
roger
9th Dec 2021 5:55 pm
thomasz
Member Since: 01 Oct 2021
Location: Kulmbach
Posts: 109
gstuart wrote:
Hi Thomas
Plse let us know how u get on and ur battery is all ok after an overnight charge
Battery is worn I think. What Type should I use?
Often read Exide 95Ah AGM. But don't know if our D4 can load it correctly (AGM needs 14.8V I remeber).
He has a BMS and there is installed a "wet" Type 100 Ah 870 cca.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum