Jondotnet
Member Since: 24 Dec 2020
Location: North York’s
Posts: 97
|
I have been getting intermittent suspension faults and the front end has been sitting lower after a few hours.
I thought it might be the front valve block so replaced that and also found both pipes to the front airbags had been joined in the past so ran some new pipes and joined them near the air bags.
End result: front end refuses to lift and getting error code C1131-92 and C1A20-64
Any suggestions on where to look next?
It has had the compressor replaced a few years ago with a AMK copy. I don’t want to start replacing that if it turns out to be something else.
Any suggestions appreciated.
|
31st Jul 2021 10:01 am |
|
|
Globetrotter448
Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1807
|
Maybe need to go back to square one. It was working prior to replacing pipes, so put old ones back and see what happens. Prior to that get some soapy water and spray all the joints and look for bubbles.
|
1st Aug 2021 6:07 am |
|
|
Jondotnet
Member Since: 24 Dec 2020
Location: North York’s
Posts: 97
|
I did that soaked everything in soap but no bubbles. The front had stopped rising properly which had led me to suspect an air leak.
Next plan is to temporarily run a new pipe from the centre valve block to the front and see if that helps.
How hard is it to test/inspect the airbags?
|
1st Aug 2021 7:33 am |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
Front ones arent too bad but you do need to extend them to find some of the leaks. Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
1st Aug 2021 7:59 am |
|
|
Jondotnet
Member Since: 24 Dec 2020
Location: North York’s
Posts: 97
|
I am guessing that involves removal??
|
1st Aug 2021 10:04 am |
|
|
Discologist
Member Since: 19 May 2014
Location: Yorkshire
Posts: 541
|
Presumably you just need to persuade the car to go into ‘super extended’ mode.
|
1st Aug 2021 10:39 am |
|
|
Jondotnet
Member Since: 24 Dec 2020
Location: North York’s
Posts: 97
|
I have spent the morning checking every pipe and valve block I can get at. I have sprayed it all with soapy water including the front struts and found nothing.
When checking the live data the gallery pressure gets up to about 720kpa which I believe is approx half what it should be. After 20 seconds of the pump running it throws a fault and the pressure drops to 100ish which I think is atmospheric pressure.
Is that going to be a leak or a very weak compressor?
Last edited by Jondotnet on 1st Aug 2021 1:40 pm. Edited 1 time in total
|
1st Aug 2021 12:40 pm |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
Just put it into off road height the jack up and remove a wheel then spray all around with soapy water. Dont forget to do the top as well. Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
1st Aug 2021 1:39 pm |
|
|
Jondotnet
Member Since: 24 Dec 2020
Location: North York’s
Posts: 97
|
Can’t get it to do anything at the moment. Front stuck down on the bump stops
|
1st Aug 2021 1:42 pm |
|
|
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
|
Try bridging the relay under the bonnet so that the compressor runs Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
|
1st Aug 2021 1:48 pm |
|
|