Member Since: 19 Feb 2017
Location: Reading
Posts: 123
Handbrake shoe fitting
I’m in the middle of changing the handbrake shoes, how tight do the discs go back on? I have got them in but there is no slack, acording to bodseys Brake bible I have to set the shoes with a torque then back of the adjuster 8 clicks? I can’t get any?2006 D3 2.7tdv6 SE Zermatt (6A)
Front and rear light protectors
EGR's Blanked
704 rims
LED Interior lamp upgrade
2014/2015 navigation maps
DAB Motion
Parrott Mki9100 Bluetooth
27th Jul 2018 2:14 pm
tayaste
Member Since: 15 May 2013
Location: Chester
Posts: 7633
Did you release the Allan bolt too?
Give the drum a tap with a hammer to centralise them.
27th Jul 2018 2:20 pm
Johnhiggs
Member Since: 19 Feb 2017
Location: Reading
Posts: 123
Done and done maybe parts are crap sizing2006 D3 2.7tdv6 SE Zermatt (6A)
Front and rear light protectors
EGR's Blanked
704 rims
LED Interior lamp upgrade
2014/2015 navigation maps
DAB Motion
Parrott Mki9100 Bluetooth
27th Jul 2018 2:33 pm
Dazz360
Member Since: 03 Sep 2016
Location: West Mids Walsall
Posts: 873
The Allen key bolt should have been reset before the drum/ disc I fitted. Shoe might not be sat true as they can be off abitMetal auto sump & fluid change (3 hrs)
LR door puddle projectors (10 mins)
Tinted Bonnet wind deflector (10 mins)
All Intercooler pipes and Tbolts (2hrs)
3 injectors replaced so far (30mins)
Sunroof drain pipes both sides 2.5 hrs)
Rear discs, shoes,pads,callipers,flexi hoses, rigid brake line, n/s upper hub carrier bush and rear n/s upper arm (13hrs over 2 days)
27th Jul 2018 3:09 pm
Johnhiggs
Member Since: 19 Feb 2017
Location: Reading
Posts: 123
I did the hex bolt before they were fitted, I've been up the road to see what it's like, binding 😕 Anyone had same prob with aftermarket parts? I know what I'm doing mechanically, never had this problem before2006 D3 2.7tdv6 SE Zermatt (6A)
Front and rear light protectors
EGR's Blanked
704 rims
LED Interior lamp upgrade
2014/2015 navigation maps
DAB Motion
Parrott Mki9100 Bluetooth
27th Jul 2018 3:37 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4983
I think you're going to have to pull it apart again as it sounds like the adjusters aren't retarded far enough. You might get away with trying to release them using the flat blade screwdriver, but the discs should go on with ease and little or no shoe contact if the adjusters and hex are right. Take your time with it as it doesn't like to be rushed!! Haven't come across ill fitting aftermarket parts, what make?
27th Jul 2018 3:47 pm
Johnhiggs
Member Since: 19 Feb 2017
Location: Reading
Posts: 123
The parts come from lr direct ltd, I've been on it since 8 30 going to pull it all apart again now2006 D3 2.7tdv6 SE Zermatt (6A)
Front and rear light protectors
EGR's Blanked
704 rims
LED Interior lamp upgrade
2014/2015 navigation maps
DAB Motion
Parrott Mki9100 Bluetooth
27th Jul 2018 4:01 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4983
If you undid the hex prior to fitting g the discs it can slip too far! With the adjusters wound all the way back and disc is still binding then this is a likely cause. The disc should go on with ease! If not you may need to adjust the hex but be careful as its tricky to adjust lever against tension!
27th Jul 2018 4:19 pm
Johnhiggs
Member Since: 19 Feb 2017
Location: Reading
Posts: 123
Ok so the only thing I can see is that maybe the epb hasn’t released enough when I did the bodsey service mode and remove fuse, can I release it any more?2006 D3 2.7tdv6 SE Zermatt (6A)
Front and rear light protectors
EGR's Blanked
704 rims
LED Interior lamp upgrade
2014/2015 navigation maps
DAB Motion
Parrott Mki9100 Bluetooth
27th Jul 2018 4:30 pm
Bardley
Member Since: 02 May 2018
Location: Hertfordshire
Posts: 462
The allen bolt shouldn't be released until the disc is on, and adjusted back to 8 clicks (off).
Then undo the allen bolt tension and tap around the drum. Re tighten the allen bolt.
If you did this before disc was refitted, it will have caused problems.
Suggest you reset to SERVICE setting.
Take discs off and check that the shoes are FULLY retracted, and against the adjuster on its retarded position.
The allen bolt adjuster should also be FULLY retracted.
Then refit disc and adjust as per manual ( Bodsy or otherwise).
Once done, and the wheel is refitted, you may have a very small amount of binding- VERY small. The wheel should turn freely tho'.
Bed them in as advised. (Mine didn't need anywhere near 10 applications to work properly).
Good luck.. and as said, take your time.2011 MY D4 HSE
Previously 2001 D2 TD5, 1996 D1 300Tdi, 1985 90 2.2 petrol.
Bikes! KTM, BMW, British, Classics and others.
27th Jul 2018 5:00 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4983
Couldn't have said it better
27th Jul 2018 6:22 pm
Dazz360
Member Since: 03 Sep 2016
Location: West Mids Walsall
Posts: 873
how you getting on now ? have you sussed it. is anyone close that could help if your still stuckMetal auto sump & fluid change (3 hrs)
LR door puddle projectors (10 mins)
Tinted Bonnet wind deflector (10 mins)
All Intercooler pipes and Tbolts (2hrs)
3 injectors replaced so far (30mins)
Sunroof drain pipes both sides 2.5 hrs)
Rear discs, shoes,pads,callipers,flexi hoses, rigid brake line, n/s upper hub carrier bush and rear n/s upper arm (13hrs over 2 days)
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum