Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
Is there a shire fab rock slider how to fit guide on here? |
|
I'm fitting my new shire fabrications rock sliders tomorrow and wondered if anyone has done a how to fit guide? I'm also planning on fitting my lr spot lights that I've only had waiting to be fitted for well since I had my previous d3 D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
4th Jan 2018 8:18 pm |
|
|
|
Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
Thanks Ian
I've not had chance to look at them yet as there still wrapped up in packaging after being delivered by the idiots known as yodel! D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
4th Jan 2018 8:29 pm |
|
|
Top-Trucker
Member Since: 27 Mar 2013
Location: yorkshire
Posts: 37
|
I found them easy to fit, I had to tap out the threads in the body for the fixing bolts as they full of crap, other than that pretty much straight forward. I didn't remove the door seal on the bottom of the door as others have, I tightened the bottom fixings first to pull the sliders down away from the door then tightened the side fixings. There's a post on fb what Ash has done when fitting his sliders, using a trim seal and different fixings. I can try find it if you like. 16ltr V8 600hp - gone
90td hard top - gone
D3 HSE
As one door shuts another one gets slammed in your face!
|
4th Jan 2018 10:08 pm |
|
|
Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
It would be handy if you could find the fb post Top-Trucker D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
4th Jan 2018 10:26 pm |
|
|
BAZ8046
Member Since: 26 Feb 2010
Location: Chatham
Posts: 278
|
I fitted a set a few months ago and they are straight forward to fit.
As has been said you may need to run a tap through the lower holes to clean the threads up.
The Shire ones fit with the original door seals. D4 2016 Landmark, Waitomo Grey.
D3 2005 HSE, Bonatti Grey, now sold but still comes back for servicing.
Defender 2002 Td5 Commercial, had a hard life but slowly being restored.
I only work so I can afford to repair my Land Rovers!
|
4th Jan 2018 10:32 pm |
|
|
Top-Trucker
Member Since: 27 Mar 2013
Location: yorkshire
Posts: 37
|
Try this disco dazboy
If no good let me know
https://www.facebook.com/groups/2079215127...0397345621 16ltr V8 600hp - gone
90td hard top - gone
D3 HSE
As one door shuts another one gets slammed in your face!
|
4th Jan 2018 10:45 pm |
|
|
Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
Top-Trucker the link works fine thanks!
Thanks for the advice Baz D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
4th Jan 2018 11:23 pm |
|
|
Top-Trucker
Member Since: 27 Mar 2013
Location: yorkshire
Posts: 37
|
Your welcome 16ltr V8 600hp - gone
90td hard top - gone
D3 HSE
As one door shuts another one gets slammed in your face!
|
5th Jan 2018 12:00 am |
|
|
Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
Do I need to remove the yellow bungs or not? D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
5th Jan 2018 11:25 am |
|
|
Disco dazboy
Member Since: 02 Dec 2013
Location: Leicestershire
Posts: 1782
|
I found this after a bit of searching
http://disco4.com/forum/topic158410.html
Sliders all fitted now but the lights will have to wait again D3 x2 now gone
Volkswagen Tiguan Allspace 4motion
|
5th Jan 2018 8:26 pm |
|
|
Top-Trucker
Member Since: 27 Mar 2013
Location: yorkshire
Posts: 37
|
Yes I removed them. Bloody pain too aswell. 16ltr V8 600hp - gone
90td hard top - gone
D3 HSE
As one door shuts another one gets slammed in your face!
|
5th Jan 2018 9:35 pm |
|
|
Mr.Tom
Member Since: 01 Jun 2014
Location: St Neots
Posts: 1641
|
Just tap them with a screwdriver or hole punch and they shatter and fall out, much easier than trying to pull them out. Sill protection - LED internal lights - LED reverse lights - boot liner - Dog Guard - Rock sliders
MY12 D4 HSE - been and gome
MY16 D4 Landmark
|
5th Jan 2018 11:09 pm |
|
|
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
|
Does anyone know what size bolts are required for fitting the shire rock sliders ? I’ve picked up a second hand set that are being blasted and coated, I’ve been told they are M8 bolts but don’t know what length to order. Will A4 stainless be the way forward ?
Thanks all. Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
|
30th Aug 2018 9:11 am |
|
|
Top-Trucker
Member Since: 27 Mar 2013
Location: yorkshire
Posts: 37
|
Yeah M8 about 20-25mm I think, I’m sure I have a spare bolt in the garage I could measure.
Stainless would be good and some large stainless washers. 16ltr V8 600hp - gone
90td hard top - gone
D3 HSE
As one door shuts another one gets slammed in your face!
|
30th Aug 2018 9:29 pm |
|
|