Member Since: 06 Dec 2017
Location: Caerphilly
Posts: 238
Tip Over Angles
My sankey camper is fairly tall. Tent is approx 5ft above ground level. Tent and frame is approx 80kg. Trailer itself is sankey with a tub on top of a tub...... if that makes sense. Other than tent all weight is below level of bottom tub which I suspect amounts to maybe 50-80kg.
Without destructive testing i.e.intentionally tipping it. Does anyone know a simple way without complicated math to figure out what the tip over angle of it might be???
Cogito ergo sum!
Disco 3 - Daisy - Ultimate combo of beast mode and comfort!
Defender 90 - Ruby - RIP
Disco 1 - Lilly - Tame!
Disco 1 - Truck with no name - Beast!
Disco 1 - Bertie - Beast!
Sankey 'twintub' DIY Camper Conversion
South African Multii-Trail Custom Overland Trailer
13th Jan 2018 11:07 pm
DG Site Moderator
Member Since: 12 Dec 2005
Location: The Gaff
Posts: 50979
Work out length of rope/strap needed to hold it tied off to rear of your vehicle (trailer at 90°)
Place Jack under trailer
Crank it until it looks like it might fall over. Tighten rope from step 1
Crank some more, etc.
13th Jan 2018 11:55 pm
Hot Tub
Member Since: 15 Aug 2017
Location: Milton Keynes
Posts: 1071
Sounds like one for Iggy he has experience of tipping them over when he is in them. I so wish he had CCTV in his garage when he got to put the legs down and his first attempt at welding failed on his roof tent conversion. He tells it so much better you have to read it. I can't remember the title but sure someone will
Somebody on here (I can't remember who ) needs to tell you one day about his first Welding attempt on his frame..........Got it looking good, bolted it to the trailer, placed roof tent on top of frame as he was a little excited, wheeled trailer out of garage, opened out the roof tent......climed up the ladder into the roof tent..... Trailer began to tip (Somebody had forgotten to put the trailer legs down)......twinging noises could then be heard as all of his welds snapped under the force....trailer tipped completely up into the air,......tent by now no longer had a frame to sit on.....I was...I mean this person was still in tent.....tent and this person fell 6 feet to the floor.......person climbed out of tent to see frame lying in pieces around him and trailer now 20 feet along the drive
No idea who is was mind
So important lesson, make sure you melt the weld into the steel...not as I, I mean this person originally did on his first frame......my current frame is super welded
14th Jan 2018 9:21 am
abermarc
Member Since: 06 Dec 2017
Location: Caerphilly
Posts: 238
Hahahaha I've actually read that trailer thread of yours. Imagining you folded up inside your tent did make me chuckle
I suppose I could find top middle of trailer at rear and hang a plum line. Then jack up one side. When bottom of plum line gets close to bottom of tyre on opposite side best stop before it goes all the way and hey presto I have my tip over angle.
That would work wouldn't it???Cogito ergo sum!
Disco 3 - Daisy - Ultimate combo of beast mode and comfort!
Defender 90 - Ruby - RIP
Disco 1 - Lilly - Tame!
Disco 1 - Truck with no name - Beast!
Disco 1 - Bertie - Beast!
Sankey 'twintub' DIY Camper Conversion
South African Multii-Trail Custom Overland Trailer
14th Jan 2018 6:09 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73119
You could always take it round the black sections of the LR Party off-road course.
Click image to enlarge
14th Jan 2018 6:19 pm
Iguana
Member Since: 14 Oct 2013
Location: 'Sunny' Zomerset
Posts: 9424
Why do people always laugh at me? (Usually while pointing)
Iggy/Ieuan
Current LR =
2015 RR Sport Autobiography
&
1992 Land Rover Defender Camper
- Gone but not forgotten:
MY10 D4 GS
MY05 Disco 3 'S'
MY14 FL2 HSE manual in Blue
MY15 Disco 4 HSE Lux in Santorini Black
MY08 Disco 3 SE manual in Buck Blue
1960 Series 2 88" (No idea why I sold it!)
14th Jan 2018 6:23 pm
Hot Tub
Member Since: 15 Aug 2017
Location: Milton Keynes
Posts: 1071
Sorry Iggy mate just in a good way
14th Jan 2018 9:30 pm
abermarc
Member Since: 06 Dec 2017
Location: Caerphilly
Posts: 238
I got a LR experience for Xmas at Eastnor. Maybe they'll let me hitch trailer up to a shinny new D5 for testing Cogito ergo sum!
Disco 3 - Daisy - Ultimate combo of beast mode and comfort!
Defender 90 - Ruby - RIP
Disco 1 - Lilly - Tame!
Disco 1 - Truck with no name - Beast!
Disco 1 - Bertie - Beast!
Sankey 'twintub' DIY Camper Conversion
South African Multii-Trail Custom Overland Trailer
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
) needs to tell you one day about his first Welding attempt on his frame..........Got it looking good, bolted it to the trailer, placed roof tent on top of frame as he was a little excited, wheeled trailer out of garage, opened out the roof tent......climed up the ladder into the roof tent..... 
Trailer began to tip (Somebody had forgotten to put the trailer legs down)......twinging noises could then be heard as all of his welds snapped under the force....trailer tipped completely up into the air,......tent by now no longer had a frame to sit on.....I was...I mean this person was still in tent.....tent and this person fell 6 feet to the floor.......person climbed out of tent to see frame lying in pieces around him and trailer now 20 feet along the drive 
