Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Strange issue....
two days ago I had this DTCs
Today I checked the fuel filter, opened the small discharge valve, switch on the ignition (not the engine), collected the fuel in a glass, but no water inside...
Any ideas?Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
28th Mar 2017 5:49 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
Member Since: 31 Mar 2015
Location: Highlands
Posts: 100
Ive had this one a few times - conventional advice is a faulty housing, however I checked mine out with a multimeter and the potential bridge circuit seemed fine.
I fixed mine by removing the sensor and giving a good clean. I changed the fuel filter, but made sure the connecting pin in the housing was clean - the filter body forms part of the circuit.
Then I cleaned up the sensor connector (to the housing) and the overall connector for the fuel filter to the main wiring loom. Use Electrical contact cleaner for all connections
The 'water in fuel error' took a few days to disappear even after that.
Click image to enlarge
MY2010 D4 3.0 TDV6 HSE Stornaway grey
28th Mar 2017 7:18 pm
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Thanks mates
I'll keep you informed.....
Just a question, is the "Water in fuel" DTC always followed by "Restricted performance" limp mode?Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
28th Mar 2017 8:17 pm
crip010
Member Since: 01 Oct 2014
Location: Twickenham
Posts: 433
I had same code week ago, changed whole assembly with sensor and new filter, so far so good. Seemed silly not to do it as so many people say to.
28th Mar 2017 9:10 pm
JksD4
Member Since: 31 Mar 2015
Location: Highlands
Posts: 100
water in Fuel error prompts the restricted performance message.
Personally on my D4 most faults have been caused by poor electrical connections. Changing the whole housing is easier and is the usual Dealer approach as they are not that bothered with diagnosis when its someone elses money.MY2010 D4 3.0 TDV6 HSE Stornaway grey
28th Mar 2017 9:25 pm
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Thank you again mates,
Through your answers and the "study" of the Workshop Manual I realized that the DTC P2264-00 (28 )is relative to the failure/issue of the "electric circuit" of the sensor and not to the effective presence of water in the fuel.
In fact, this latter case is indicated by DTC P2269-68Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
29th Mar 2017 7:33 am
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Short report:
The day that I checked the presence of water, I cleaned with contacts cleaner all the electrical connectors....
AT the moment no DTCs.... we will see....
Otherwise, new filter housing LR045519 ordered......Discovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
30th Mar 2017 7:17 am
dgardel
Member Since: 03 Nov 2009
Location: Greater Venice
Posts: 2025
Damn !!!!
Error reappeared ....
Now we know what to do on the weekend.....
Hurray St. IIDToolDiscovery 5 tdv6 HSE Corris Gray Outback Engineering Limited Edition IID Pro MV License
31st Mar 2017 9:37 am
JksD4
Member Since: 31 Mar 2015
Location: Highlands
Posts: 100
had this again after a couple of years - just changed filter and cleaned all connections.
started engine and cleared fault with iid. has been error free for the last few days.MY2010 D4 3.0 TDV6 HSE Stornaway grey
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
