Member Since: 05 Feb 2008
Location: Wiltshire
Posts: 251
Rusty Hubs - Pic added
Looking inside the alloys of the D4, looks like the hubs are develeping a good number of rust spots. Anyone else had this problem before I start hassling the dealer...??
Cheers
John
Edit - Pic added and have given to dealer for consideration - will report back. Thansk for the feedback chaps
Click image to enlarge
[/img]
Last edited by jonnyboy on 18th Apr 2011 2:25 pm. Edited 1 time in total
By hubs I guess you are refering to the disc bell.
JLR current coat these in a cheap material using zinc dust as the sacrificial corrosion agent. The material is crap when compared what could be used, however like everything in the automotive industry it is made to a cost.
The coatings for this type of material are applied too thin and are only design not to rust whilst sitting in the showroom or dealer forecourt.
O/E builders like McLaren, Bentley, Lotus tend to use a much better material- I could bore you for hours on the technicalities, for the sake of everone else I won't
The cost difference is about 30-40p per disc to someone like JLR.
My advice is to moan at the dealers, they may not be very switched on and replace these for you (it will mean more work for Brembos Polish plant.) if they won't and you want the hub /bell to look nice, wire brush them down, put a coat of a Zinc rich paint on and then a coat of something like smooth hamerite. Do not paint the braking face or the hub (wheel) mounting face (The rear discs have a raised area in the centre of the hub which should not be painted, outside this is may be covered.
The best finish as used by Mclaren etc is a zinc flake which you can coat all over the disc, and is design to come off with out effecting the pads within 5 -10miles of use. this material should give 3-5years of normal use and upto 10 years of limited use.
The photo below show a Geomet finish, which is a type of zinc flake, these are D3 front discs and also show the difference between the std and V8 disc
Click image to enlarge
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
All true, but I have had several new cars and never had such a rapid development of rust as on the D4.
Then again, the salt used this winter set an all time high for this area; I find that a larger problem than the hub design.
Edit: CG replied before me.
15th Apr 2011 12:43 pm
jonnyboy
Member Since: 05 Feb 2008
Location: Wiltshire
Posts: 251
CG - Great post thanks. Am going to get the dealer to look at this when its in in a few weeks for a few bits and bobs. Will post back as to what he says
Before you rush back take a look at your picture again.
You will see the top of the locking cap has also gone rusty, this is in a different coating for both the bell and locker to corrode in a similar manner so early in the vehicle life indicates to me the vehicle has been either standing in water, near the sea or has been jet washed with a strong cleaner. (presuming the nut have not been swapped onto your vehicle)
either way I would be after discs and all the wheel nuts, as you may get rust staining behind those stainless cap on the other nuts.
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
19th Apr 2011 12:43 pm
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6403
painted mine with rustproof hammerite and been fine ever since that includes calipers
looks as if LR uses or nor protective coating on there
19th Apr 2011 1:34 pm
chalky
Member Since: 21 Aug 2008
Location: Yorkshire
Posts: 3145
As said above, try painting the surface with something like QD90.
This resists a certain amount of heat and will look much more pleasing upon the eye.
I'm sure if you got down underneath the thing and looked at the Chassis the rust on that would be much more alarming, it's probably because you can see the surface ?
That said and again as pointed out I noticed the corroded locking wheel nut first
19th Apr 2011 2:02 pm
cherokee
Member Since: 03 Jul 2007
Location: preston
Posts: 562
IMHO, For £5o,ooo that shouldn't happen, paying that sort of cash you shouldn't have to be getting a
paint brush or spray can out to stop rust, after such a short time, no matter how much salt was put down.
Just my opinion.Always walk behind a Shooter and
In front of a Sh*ter
10th May 2011 7:55 am
grzesiul
Member Since: 11 May 2008
Location: UK
Posts: 6403
you spent 50K on a land rover???????? :O
crazy or what?
10th May 2011 8:05 am
cherokee
Member Since: 03 Jul 2007
Location: preston
Posts: 562
I didn't spend 50k on a LR but I think a D4 HSE new costs that, the Landmark costs 46k and I dont
think they put different wheel nuts and hubs on a basic D4, and I wasnt knocking anybody for
painting them there selves, just saying they shouldn't have to do it IMHO!!!
Discs and nuts as the same parts as the D3 all models (most overseas markets do not get locking nuts apparently)
the rear dicss on my 2006 which have done 75k are less rusty than those, the locking nuts I ditched a long time ago.
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
10th May 2011 12:28 pm
Grunders
Member Since: 30 Apr 2011
Location: Manchester
Posts: 2329
My dicss havent gone rusty either. If it ain't broke... Take it apart anyway, how else you gonna find out how it works
10th May 2011 12:43 pm
jonnyboy
Member Since: 05 Feb 2008
Location: Wiltshire
Posts: 251
Update - the car went in yesterday for a number of warranty items (nothing major) and was returned with brand new discs and locking nuts without a murmor of a quibble.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
overuse of salt.
