Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
GAP Diagnostic Announcement-2016-07-25-Apple App & More
Hello Everyone
First, we would like to thank all our customers, beta testers and the community for your continuous support. Many new additions were the results of your feedback and suggestions. We could not be where we are without you!
As many of you already know by now, a new App, version 2.9, for Apple devices was released over the week end. We’ve also released a new special firmware available for beta testers only at the current time. I will do a second post shortly showing each point in detail but here’s a resume of the new additions when using both the new App and firmware or using the new App only with an older firmware.
Top Bar (new and old firmwares): A new bar was added which shows the current connection and ignition status as well as battery voltage.
Faults function (new and old firmwares): Advanced Read
-Status bit flags default selection can be saved for future use
-Status bit flags are visible as icons on top of fault descriptors
-Status bits can be included in the exported emails
Height Adjust (new firmware only): A new and more intuitive screen to adjust your suspension height with default and saved settings. Contrary to our previous method, height changes are relative to the default height and not the current standard height.
0 -> 25: current height, 0 mm, or default in this example is shown on the left while the selected height setting (My offroad height in this example) is shown right, + 25 mm
Click image to enlarge
20 -> -10: current height, +20 mm relative to the normal height (0 mm), shown on the left while the selected height setting (Motorway in this example) is shown right, -10 mm relative to the normal height (0 mm).
Click image to enlarge
Click image to enlarge
Height Control (new firmware only): This function allows you to remotely control your current height (Access, Normal, Offroad) and lower both axles to the bumpstops.
Suspension Calibration (new firmware only):
-New manual calibration layout
-New guided calibration function. This unique method eliminates the need for calculations, even ground and requires only one iteration. The whole process takes 5 minutes.
Click image to enlarge
Guided calibration instructions:
• The first corner to be calibrated is the front left corner (1).
• Place your measuring tape as instructed and use the up and down arrows (2) to reach the required height (3).
• Once completed, click on Send (4). The next corner to be calibrated will now be high-lighted.
• Repeat the previous steps for all corners.
New Suspension Test Valve function layout (new firmware only)
Click image to enlarge
Live values:
-All live values (PIDs) are now available for all supported vehicles (L322: except for older BMW type ECUs, new firmware only)
-Trigger function which allows custom audible or vibration alarm and automatic start/stop logging of live values. (new and old firmwares)
Click image to enlarge
Trigger example:
• The live value increases and passes the Start target of 20 % (first red dotted line)
• Recording begins and the previous data is kept (2 seconds, as set)
• The Stop condition is met at around 6.5 seconds, hence the trigger indicator (red dotted lines)
• Recording continues for 4 seconds as set
• Enabling the Buzzer will generate a sound when the condition is met. Perfect when moni-toring live data. Can be used without using the automatic recordings feature.
-Favourite Fast Add feature which allows adding live values to favorite list quicker. (new and old
firmwares)
Click image to enlarge
• Click on the star when viewing an ECU live values
Click image to enlarge
1- Click here to create a new list
2- Current favourite lists are shown here
3- Click on the star to add the live value to this favourite list
-Layout improvements (new and old firmwares)
-Selection of which live values to be exported and viewed (logs). (new and old firmwares)
Click image to enlarge
Car Configuration File (new and old firmwares):
-Complete CCF list can be edited upon request.
-Favourite Fast Add feature which allows adding configurations to favorite lists quicker.
ECU Info (new firmware only): This new layout is the basis for what will be the next step reflashing wise. It now shows which ECUs are up to date and those for which a newer version is available. If you are testing this function, please send us the results using the send e-mail button for our records. This will help us validate the automatic file selection algorithm.
Click image to enlarge
An historic of each ECU Info scan is saved and can be recalled.
Tool Activation (new and old firmwares): Initial activation of the IIDTool can all be done within the App when the mobile device is connected to the internet. Additional licences can also be entered in the App.
New French version (except for live values and car config, new firmware only)
Documentation: The user manual was completely overhauled and will be released in the comming days in French and English.
Jaguar support: It is now possible, upon request, to use the IIDTool BT or Pro on 2008 and up Jaguars.
Work on the Android App is still under way. If you are using Android devices only, please do not update to the special firmware 2434 (English), 2435 (French) or 3630 (Pro English), 3631 (Pro French) and up since the firmware is not backward compatible with earlier App versions. You can, however, revert back to the latest beta if Android usage is required after using it on an Apple device.
Our current beta testers using Apple devices can benefit from these new additions by updating the App to V2.9 and IIDTool firmware to:
BT:
-Special Build 2439 (English, French upon request)
Pro:
-Special Build 3643 (English, French upon request)
We strongly recommend updating your mobile device operating system (iOS) to the latest version prior to using the new App and firmware.
As usual, feedback is more than welcome! For those who are not currently beta testers and want to test the new App and firmware simply send us an e-mail or a PM.
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73079
to GAP & Robbie
from the original Diagnostic Dummy.
25th Jul 2016 6:03 pm
trainmanone
Member Since: 19 Dec 2014
Location: stockport
Posts: 366
is this update not available for the non bt version of the IID tool?
25th Jul 2016 6:06 pm
Gareth Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26774
Great news that you now cover Jaguar cars 2008 onwards.
Could you clarify if I would need separate IIdTool BT units for my Discovery 4 (2013) and my Jaguar F Type 3.0s (2014) or would a single unit with additional license cover both vehicles?
Could you let me know the cost? (Pm if you want)
Cheers
25th Jul 2016 6:14 pm
PatGAPInnov Site Sponsor
Member Since: 02 Dec 2011
Location: Montreal
Posts: 745
Unfortunately, the limitations of the integrated interface (the screen itself) prevent us from implementing those new additions on the non-BT units.
Up until now, the gap function wise between the non BT and BT was small. Addition of more complex feature will however favor the BT thus increasing this gap.
We do, however, continue to update the non-BT units with new routines and the likes.
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26774
Nice one ordered 8)
25th Jul 2016 6:52 pm
geoff.
Member Since: 24 Jan 2010
Location: West kent
Posts: 8531
thats the difference when people know this system , well done GAP
25th Jul 2016 7:08 pm
Dudleydisco
Member Since: 20 Jun 2014
Location: York
Posts: 853
Great work as ever Pat Thanks for the update too D4 MY14 XXV - RLD/IID BT
D4 MY13 HSE Lux - RLD/IID BT
P38 RR - Sad parting
110 - Even sadder parting
S3 88" - Still going strong after 23 years of ownership
25th Jul 2016 7:27 pm
tayaste
Member Since: 15 May 2013
Location: Chester
Posts: 7633
Right, gonna have a play with the ECU info
25th Jul 2016 7:48 pm
SWR
Member Since: 07 Nov 2013
Location: Warwickshire
Posts: 840
Awesome stuff.
Will update the firmware and then do the guided suspension calibration.
Great support as always. D3 HSE TDV6 Auto. Bonatti Grey.
Mods:
V8 Brake upgrade (front Only), Full height Luggage guard, Rubber mats all round, RLD spare wheel protector, Terra Firma Steering and Transmission guard, Smoooooth Nappa steering wheel, Clock on dash and Reverse home lights. National Luna split charge system, front and rear light guards, Danhag GSM (on loan), JE stage 1 remap... Zero money
25th Jul 2016 7:55 pm
DSL Keeper of the wheelie bin
Member Since: 11 May 2006
Location: Off again! :-)
Posts: 73079
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
