Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
Steering angle sensor sleeve repair.
Morning gents, I've been having the bong 'HDC fault, special programmes unavailable" blah blah blah fault for a while, forum member rusty came up with his nanocom (what a top bloke) and managed to diagnose a steering sensor issue. He recalibrated it and the fault cleared. The minute I turned the steering wheel it came back.
I've had a mooch through the forum and found a few related topics but have a couple of questions regarding the actual repair.
I've been in the car this morning and noticed the sleeve is able to turn. I would imagine this is why the calibration goes out and the car gets confused.
I'm just looking to confirm the actual part that needs fixing in place. I have attached a pic. It's a bit of a pig to get too but I think I'll do the repair this weekend and post up a how to.
Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
Hi mate, funnily enough I was just reading that one. I could do with a bit more clarity on what to glue to where. Does it have to be in a certain position to glue it ? Would my 4x4 screen show me when the wheels are showing straight ahead vs the steering wheel and front wheel position ? That's pretty much straight ahead to glue then maybe ? I'm a bit confused. Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
15th Dec 2015 2:52 pm
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
Anyone ? Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
15th Dec 2015 9:31 pm
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
Well I'm pleased to say I've now cured the fault and again a huge thank you to forum member rusty who came and recalibrated the sensor. I've driven the car quite a lot today and can happily report its. Now fixed. I'll follow up with a few photos and a how to later. Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
4th Jan 2016 2:45 pm
Kingwarrior
Member Since: 06 Feb 2016
Location: Beds
Posts: 6
Any chance you could let me know how to fix this as I've just had the shaft changed on my car and got same problems thanks
14th Feb 2016 6:05 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20727
The yellow plastic gear needs to be secure against the metal steering column My D3 Build Thread
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
The method I used was.... Get a small 5ml syringe like the ones that come in kids calpol. Take the plunger out and fill 3/4 of the way with sticks like sh*t adhesive. Apply between the greeny yellow sleeve and the metal sides of the u/j I had to fill the syringe a second time. The adhesive is very thick and won't run. Just make sure you don't get it on the White plastic ring where it's located in the black sensor housing. When it's dry recalibrate the steering angle with a nanocom or IID and your sorted.Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
Have you changed your grill since your profile pic? Drove past a Black D3 Friday...I think with the D3 sticker across the rear top of the rear window.
14th Feb 2016 9:31 pm
Kingwarrior
Member Since: 06 Feb 2016
Location: Beds
Posts: 6
I have just had my steering shaft changed and the computer is showing the wheels cranked slightly left when the wheels are pointing straight what is the way to put this straight as I'm getting HDC fault codes since having the shaft changed thanks guys
14th Feb 2016 9:44 pm
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
King warrior, yes that's why your getting the HDC fault. There are accelerometers in the gearbox apparently that go nuts when you drive forward and your steering angle is off. It causes a confusion. A reset and recalibration is needed. Just have to check the sensor is moving ok on the shaft.
Rock if that was aimed at me ? Nope my D3 is buck blue and no other mods as yet. Or sticker. It's in the glove box. Forum member rusty has a black D3 with a different grille I believe Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
14th Feb 2016 10:15 pm
Kingwarrior
Member Since: 06 Feb 2016
Location: Beds
Posts: 6
Nice one cheers so can that recalibration be done on all the computers that plug in ?
14th Feb 2016 10:38 pm
Discomadness
Member Since: 19 Jan 2015
Location: Caerphilly
Posts: 2256
I don't think so mate. I'm not sure altogether which ones will or won't but I know the nanocom amd IID tool both can do it. Jarrod
Current : D3 2007 HSE - AKA the lemon
-beanie grille
-detango with led bulbs
-club body off rebuild. TWICE.
15th Feb 2016 8:11 am
highlands
Member Since: 11 Jan 2010
Location: NW Highlands
Posts: 5095
Any of the 'normal' OBD code readers / Torque, etc won't be able to do anything with the steering sensor.Black 05 TDV6 HSE Auto
Grey 05 TDV6 HSE Auto (Gone)
54 TDV6 SE Man (killed by me )
15th Feb 2016 2:18 pm
Tommy18
Member Since: 03 Aug 2017
Location: Essex
Posts: 3
Hi
Currently holidaying Spain with the family and our disco was the preferred mode of transport.
As soon as the wheels hit France I started receiving all dash information like Stability control off, drive with care. Brake assist off and hdc fault.
This resets temporarily for a while after ignition on off bit comes back on.
It's rather annoying mainly due to the suspension dropping on the motorways.
I brought my scanner with me and I have perminant and intimitant steering angle codes.
My questions are. Do the D4s suffer with the ring slipping on the steering column as the D3s? As I'm struggling to find a D4 thread.
I though maybe landrover took the liberty of fixing it
I've had my head under the footwell with the panels removed and doesn't seem to be slipping or having any play. So could i just have a broken sensor?
Are they easy to replace? Besides me having to have it calibrated afterwards?
Many thanks
Tom
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
) 
