Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
new sensor nanocom evo
sorry for my bad english ,
I'm trying to replace the left rear height sensor .
you have suggestions for the right sequence with nanocom evo ?
Matteo
Disco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
13th Sep 2015 5:41 am
Teospock
Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
with nanocom evo it is not possible to replace the height sensor?
Disco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
13th Sep 2015 11:01 am
MikeO
Member Since: 15 Jan 2014
Location: The Cotswolds
Posts: 1390
Presumably just replace the sensor and then do a height calibration. You can do that with the Nanocom.2016 Skoda Octavia VRS Estate
<gone>2009 FF Vogue TDV8 Buckingham Blue</gone>
<gone>2015 BMW 520D SE (not my favourite car)</gone>
<gone>2009 D3 HSE Galway Green</gone
13th Sep 2015 11:05 am
MikeO
Member Since: 15 Jan 2014
Location: The Cotswolds
Posts: 1390
And take a note of the calibration values for the other corners before you start.2016 Skoda Octavia VRS Estate
<gone>2009 FF Vogue TDV8 Buckingham Blue</gone>
<gone>2015 BMW 520D SE (not my favourite car)</gone>
<gone>2009 D3 HSE Galway Green</gone
13th Sep 2015 11:08 am
Teospock
Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
hi Mike0
I have already tried to do what you write
I have bought a sensor left rear.
Parte: LAND ROVER VERA POSTERIORE SINISTRO ARIA SOSPENSIONE ALTEZZA SENSORE
Warranty: 2 Year
Land Rover Discovery 3 2004-2009
Position: Rear Left
OEM Number: LR20159 RQH500053
Notes: Up to Chassis No 9A999999
I was handed a sensor with code AH22-5B732-AC
checking the technical bulletin
http://www.disco3.co.uk/gallery/albums/use...bility.pdf
I can not find the corresponding.
The sensor is supplied without bracket, and I had to do myself
is this my problem?
my vin 146a395066
I have bought a sensor wrong?
tkyDisco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
i try..
You can confirm the right steps?
466 front 485 rear wheel center to the archDisco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
13th Sep 2015 3:08 pm
MikeO
Member Since: 15 Jan 2014
Location: The Cotswolds
Posts: 1390
My *guess* is that's a RH rear you've got? The TSP you linked quotes
AH22-5B732-AB for the RH rear and BH22-5B732-AA for the LH rear
You have AH22-5B732-AC which sounds suspiciously like a RH rear with a later revision?2016 Skoda Octavia VRS Estate
<gone>2009 FF Vogue TDV8 Buckingham Blue</gone>
<gone>2015 BMW 520D SE (not my favourite car)</gone>
<gone>2009 D3 HSE Galway Green</gone
13th Sep 2015 7:00 pm
Teospock
Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
That 's what I think.
Now I try to buy another , doing more attention to the code .
Matteo
Disco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
14th Sep 2015 7:32 am
karpouzih Site Sponsor
Member Since: 02 Feb 2013
Location: Lemesos
Posts: 150
Hi guys,
Bit more info for you if you needed it regarding the calibration process after part replacement, can be found in the following manual at page 13:
Member Since: 14 Mar 2015
Location: Bergamo
Posts: 27
thanks cris ,
a question off topic ... where can I find the instructions to enable 3 blinking lights .
i must change ccf ? how to recognize the right file ?
Site genesis one login it by the same pass nanocom site ?
all the information you can give me or tell me where to look for are unwelcome
Disco 3 hse
-guard arms
-guard light + egr acrylic protector
-rear ladder
-dist. 25mm front 30mm rear
-mudflap
-T-max dual battery whit optima yellow top
-gg at2
-nanocom evo- 3 flash light- no sound belt
-ebc green
- mudtech rear protection
-egr blanked- decat
17th Sep 2015 9:49 am
karpouzih Site Sponsor
Member Since: 02 Feb 2013
Location: Lemesos
Posts: 150
Hi Teospock,
In order to enable the 3 Flash Turn Indicators you will need to edit the CCF.
This is a simple procedure as you can see in the following instructional video:
Once you have enabled the 3 flash from the CCF, if the vehicle doesn't appear to have it activated, this would mean that you have an older firmware version in your BCM (Body Control Module). You would then have to update the vehicle BCM to a newer firmware version.
Here are two threads on our forums with people performing the upgrade and enabling 3-flash for more info:
You are correct the Genesis site login details are the same as the Nanocom website, if you do run into any problems please post on the forums or send us an email and we'll sort you out.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
... where can I find the instructions to enable 3 blinking lights .
