Member Since: 31 Mar 2014
Location: Nottingham
Posts: 11
Upper tailgate switch full of salt?
Went to put my bag in the boot this morning and couldn't open the tailgate. Could open it with the help of my son and the two finger lock trick on the dash. The switch felt like there was nothing under the rubber.
When I got to work I nearly asked my boss if I could feel his tailgate switch as my feels a bit funny but decided this could be misunderstood.
I Looking at other posts I decided it must be the micro switch so I pulled off the rubber cover and I found what looks like more salt than a Siberian salt mine.
Click image to enlarge
I noticed that the same white deposit is round the handle fixing screws, is this really salt? I have so far resisted the lick it to see, again not sure the neighbours would understand.
Tried to unscrew the handle to get a better look but most of the screws are stuck fast and one just spins round. What do the screws screw in to?
Member Since: 12 May 2009
Location: Herefordshire
Posts: 384
The screws go into brass type inserts that are . They either don't grip or fall apart. Mine currently has only two in. The other holes I have covered up with gaffer tape waiting till I need to replace the assembly again......
Another terrible design...... like the torx headed bolts on the bottom of the front bumper
Ids
2nd Jul 2015 11:46 pm
MGCarr
Member Since: 15 Jul 2014
Location: Lancashire
Posts: 703
Mscammells
Join the club, that is exactly how my 07 plate switch looked when I replaced it about 12 months ago.
1997 Defender 90 for the kids and I to have a go at some competitive off road RTV and Tyro trials, daughter picked up her first trophy over the August Bank Holiday.
Previous Land Rover history
1996 P38 4.6 V8 Autobiography
1996 Discovery TDi 300
1972 Range Rover 3.5 V8
LWB Hard Top Series 3
LWB Truck Cab Series 2A
Not been without a Land Rover for over 40 years - I must need therapy!
3rd Jul 2015 1:22 am
MGCarr
Member Since: 15 Jul 2014
Location: Lancashire
Posts: 703
Try this post for a cheaper option than replacing the whole tailgate handle!
Mods - should the above post be in the wiki as there seems to be a lot of switch failures needing a £70 or £80 handle when it appears that there is a much more cost effective solution?
1997 Defender 90 for the kids and I to have a go at some competitive off road RTV and Tyro trials, daughter picked up her first trophy over the August Bank Holiday.
Previous Land Rover history
1996 P38 4.6 V8 Autobiography
1996 Discovery TDi 300
1972 Range Rover 3.5 V8
LWB Hard Top Series 3
LWB Truck Cab Series 2A
Not been without a Land Rover for over 40 years - I must need therapy!
3rd Jul 2015 1:36 am
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
The idea behind the Wiki is that it gets its content from the forum members. Too few of us contribute so give it a go and add the information.
Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 26753
Robbie is correct. Anyone can add an article to the Wiki. Its worth a look, as it is not as difficult as you think
3rd Jul 2015 8:05 am
Mscammells
Member Since: 31 Mar 2014
Location: Nottingham
Posts: 11
Thanks all for the information, a little disturbed at Robbie's D4 licking link but live and let live I say.
After a bit of chipping away the metal part of the switch it is moving again and the micro switch looks fine underneath. I can see metal will give up as some point, so being a bit of a geek I am going to look at 3D printing some sort of replacement. If I get this working I will post the file here.
SnapCurrent: Discovery 3 06MY (55 reg) HSE Auto Zambezi Silver Allisport Fast Road Intercooler, V8 Brakes, Silicone IC Hoses, EGRs Blanked, Remapped, De-Cat pipe, FBHIC
Freelander 2 2007 HSE Manual Tambora Flame
Previous: FL2 56 reg SE Manual Black (written off )
Disco 3 06 reg B7S Manual Rimini Red
Disco 2 TD5 Y reg ES Manual Blue - Chipped
Several Discovery 300 TDis
3rd Jul 2015 9:10 am
MarkOne
Member Since: 23 Jul 2011
Location: County Antrim
Posts: 3345
I tried to remove mine a month to paint it and a couldn't get it off it was that bad.
3rd Jul 2015 9:13 am
karlosbu
Member Since: 02 Sep 2008
Location: Worcestershire
Posts: 335
I've had exactly the same issue twice now. First time I replaced the entire handle as I fancied a nice colour coded one anyway. After 2 years that one started playing up to so I removed the cover to reveal the same mess underneath, I removed the metal plate cleaned it up with wire wool, sprayed it with WD40 and replaced (removing plastic switch housing from handle makes replacing cover simple)...works a treat now and a 5 minute fix if it corrodes again
3rd Jul 2015 9:23 am
MGCarr
Member Since: 15 Jul 2014
Location: Lancashire
Posts: 703
Robbie & Gareth
My apologies, I mistakenly thought that the ability to add items to the wiki was restricted to those with specific permission to edit the wiki.
1997 Defender 90 for the kids and I to have a go at some competitive off road RTV and Tyro trials, daughter picked up her first trophy over the August Bank Holiday.
Previous Land Rover history
1996 P38 4.6 V8 Autobiography
1996 Discovery TDi 300
1972 Range Rover 3.5 V8
LWB Hard Top Series 3
LWB Truck Cab Series 2A
Not been without a Land Rover for over 40 years - I must need therapy!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum