Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
Help!, replaced a front bearing and steering column, FAULTS
Hi, I replaced the front drivers side wheel bearing today and replaced the lower steering column.
I now have two issues. The first being when I turn the steering wheel it comes up with HDC fault. The second being that when driving down my track for a test drive, the front drivers side caliper seems to be coming on and the ABS seems to be going haywire.
ANy ideas? I tried to make sure that I did not turn the steering wheel when replacing the lower column, however once disconnected from the shaft, the weight of the wheel re-centered itself... so Im wondering if Im half a turn out.
Is there a way I can check without screwing the clocksprings etc?
I'm wondering if the brake thing could be to do with the wheel speed sensor as I've just remembered I did not remove it when replacing the bearing.
Thanks for your help!
2nd Mar 2015 6:25 pm
armalites
Member Since: 17 Aug 2013
Location: Herefordshire
Posts: 1918
Sounds like the steering out, the steering angle sensor thinks you are already steering so when you turn the brain thinks something is wrong as it has turned too farIID PRO
MSV Extreme
Nanocom One
2nd Mar 2015 6:30 pm
discoteca
Member Since: 08 Mar 2010
Location: Warwickshire
Posts: 1477
Steering angle sensor was my first thought too. You will need access to some diagnostic equipment to recalibrate.
2nd Mar 2015 6:34 pm
mattm
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
,
Can I not just re adjust the steering wheel?
2nd Mar 2015 6:48 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20781
I have seen the column fitted incorrectly in the past. May be worth checking before delving deeperMy D3 Build Thread
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
Thanks guys,
Mickey, what would I be looking for?.. how do I tell?
If I turn the wheel from lock to lock and count the turns would that help? would I rick wrecking the clock springs (not exactly sure what they are).
2nd Mar 2015 7:23 pm
lynalldiscovery
Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274
Recent post where the guy used the 4x4 info screen to centre the steering wheel after doing some work
Not sure how much your dealer charges but the I930 tool shows steering wheel sensor angle.
2nd Mar 2015 7:24 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20781
mattm wrote:
Thanks guys,
Mickey, what would I be looking for?.. how do I tell?
If I turn the wheel from lock to lock and count the turns would that help? would I rick wrecking the clock springs (not exactly sure what they are).
Need to check where the centre point of the rack is, what position the steering wheel is, and how the column has been ffittedMy D3 Build Thread
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
I'm pretty its the steering wheel being out by 180 degrees.
I turned the wheel about 180 degrees from straight ahead to access one of the bolts, however when I withdrew the upper joint of the steering column, the weight of the steering wheel r-centred itself.... I'm just not sure which way it went.
Can you fubar the wheel speed sensor if you don't remove it when changing a wheel bearing? Im pretty I didn't hit it inadvertently with a hammer when drifting off the old hub?
2nd Mar 2015 7:40 pm
mattm
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
Can the lower shaft be fit incorrectly?
It seemed to have a notch in it somewhere for the bolt... or it felt like it did when I was trying to re-align it.
2nd Mar 2015 7:48 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20781
mattm wrote:
Can the lower shaft be fit incorrectly?
It seemed to have a notch in it somewhere for the bolt... or it felt like it did when I was trying to re-align it.
Disco_Mikey wrote:
I have seen the column fitted incorrectly in the past. May be worth checking before delving deeper
This will more than likely be your issue.
In fact, you even answered your own question
mattm wrote:
I'm pretty its the steering wheel being out by 180 degrees.
I turned the wheel about 180 degrees from straight ahead to access one of the bolts, however when I withdrew the upper joint of the steering column, the weight of the steering wheel r-centred itself.... I'm just not sure which way it went
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
OK,
So I think the lower bit is OK, as from memory, the bolt is in the same position as it was before I started the procedure, (and why I needed to turn the wheel in the first place in order to get to it).
My main question is:
If I start messing with the top joint, which means turning the steering wheel by 180 degrees one way and retrying and then trying the other way.... will I risk breaking something in the clock spring mechanism if I'm turning it effectively 180 degrees past its intended limits?
Secondary question, would this be enough to mess with the ABS system, or could this be an issue with the wheel speed sensor.
Im just summoning up the motivation to go back out in the cold, wind and darkness.
2nd Mar 2015 8:19 pm
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20781
You can see which way it needs to go with a diagnostic tool, which is capable of reading the live data of the steering angle
Member Since: 15 Jul 2014
Location: Lancashire
Posts: 703
Is the groove in the shaft where the bolt locates continuous around the circumference of the shaft or just a notch out of one side?
1997 Defender 90 for the kids and I to have a go at some competitive off road RTV and Tyro trials, daughter picked up her first trophy over the August Bank Holiday.
Previous Land Rover history
1996 P38 4.6 V8 Autobiography
1996 Discovery TDi 300
1972 Range Rover 3.5 V8
LWB Hard Top Series 3
LWB Truck Cab Series 2A
Not been without a Land Rover for over 40 years - I must need therapy!
2nd Mar 2015 8:37 pm
mattm
Member Since: 13 Apr 2014
Location: Aberdeenshire
Posts: 122
SUCCESS!!
Firstly, thanks guys for your help!
The steering wheel was 360 degres out. I suspected it was turning to the right due to it trying to brake that calliper whine going in a straight line, so I undid the bolt, turned it to the left and hey presto... no errors!
The steering feels a lot better and a lot less 'feedback' from bumps through the wheel.
Annoyingly what I thought was a wheel bearing noise, is still there. So Im assuming its either diff, driveshaft or the GG AT's.
Im going with the latter.
...now just to sort out the brake judder and sticking rear brake calliper??...
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum