I write this having had first AA Chap out... Sat in Tescos car park after SWMBO took the D4 out and the EPB appears to have jammed on, I came to the rescue, with info off here in that I removed said cup holders and base plate to see wire loop, pulled hard enough to bend screwdriver shaft, but no 'clunk', so opted for AA.
'Ke'v arrived asked me what the issue was, which was re confirmed to him, as had been done to the call centre, where he took a socket shaft, tried what I did and then pronounced it 'Royally you know what Sir, I'll organise a lift truck for you'
So is there any self help advice as I know wait the two hours whilst SWMBO has had enough of the D4 and headed home.....Mitch
I never forget a face, but in your case I'll be glad to make an exception......
4th Jun 2014 7:16 pm
Jlrjim
Member Since: 05 Mar 2014
Location: In the Land of Rover
Posts: 108
Does this work?
Ignition off
Hold EPB down
Ignition on
System resets and releases
5th Jun 2014 11:56 am
steveraspberry
Member Since: 18 Sep 2011
Location: Nr Sevenoaks,Kent
Posts: 2081
Probably too late now (Sorry) but doesn't a 2011 still have the red handle under the cup holders? If so I'm just wondering what you bent your shaft on !!!! ....So to speak.
Is it sorted now?My17 Volvo XC90 Inscription
MY15 Mitsubishi L200 Barbarian
RGK Tiga Fx Wheelchair,
Large Alsation called Abbs
Medium blue Staffie called Piglet
Medium Alsation called Bailey
5th Jun 2014 2:36 pm
markate
Member Since: 17 Sep 2011
Location: England
Posts: 704
Red handle under cup holders doesn't release the EPB but releases the Drive Select button.
5th Jun 2014 4:23 pm
steveraspberry
Member Since: 18 Sep 2011
Location: Nr Sevenoaks,Kent
Posts: 2081
Are you sure about that? My17 Volvo XC90 Inscription
MY15 Mitsubishi L200 Barbarian
RGK Tiga Fx Wheelchair,
Large Alsation called Abbs
Medium blue Staffie called Piglet
Medium Alsation called Bailey
5th Jun 2014 5:06 pm
Robbie
Member Since: 05 Feb 2006
Location: ¯\_(ツ)_/¯
Posts: 17932
Well I think we are all sure about that - what are we missing??
Land Rover - Turning Drivers into Mechanics Since 1948
Member Since: 17 Sep 2011
Location: England
Posts: 704
steveraspberry wrote:
Are you sure about that?
Yes.
On vehicles with Drive Select there is a red handle under the cup holders and then to access the EPB release wire you need to remove the plastic cover plate (2 screws) and then give a hard pull on the wire with the loop on it.
Don't be tempted to pull the red lever to see what happens as it usually results in the vehicle having to be recovered to the Dealer for a gearbox reset.
5th Jun 2014 7:10 pm
steveraspberry
Member Since: 18 Sep 2011
Location: Nr Sevenoaks,Kent
Posts: 2081
I'll shut the up then.My17 Volvo XC90 Inscription
MY15 Mitsubishi L200 Barbarian
RGK Tiga Fx Wheelchair,
Large Alsation called Abbs
Medium blue Staffie called Piglet
Medium Alsation called Bailey
5th Jun 2014 8:22 pm
steveraspberry
Member Since: 18 Sep 2011
Location: Nr Sevenoaks,Kent
Posts: 2081
I was just following the advice on this forum:
http://www.disco3.co.uk/forum/topic74606.htmlMy17 Volvo XC90 Inscription
MY15 Mitsubishi L200 Barbarian
RGK Tiga Fx Wheelchair,
Large Alsation called Abbs
Medium blue Staffie called Piglet
Medium Alsation called Bailey
Member Since: 23 Aug 2007
Location: Kent
Posts: 10564
DM its a D4 so may be under warrantyMY17 D5 1st Edition Namib Orange
MY15 D4 HSE Kaikoura Stone
MY12 D4 HSE Nara Bronze Sold and gone
MY11 D4 HSE Stornaway Grey Sold and gone
D3 S spec Silver Sold and gone
Tow bar, full length roof bars, side steps, tow bar storage unit, surround camers.
D4 camera club
6th Jun 2014 11:14 pm
gensetsteve
Member Since: 01 Jan 2014
Location: hampshire
Posts: 340
What causes in general the epb to jam on. Is it because there is too much clearance at the shoes and the main unit has to pull so much cable in it jams ? I have hopefully recently sorted mine out too much clearance is bad and too little drags and cooks the disc and shoes. Considering how simple a lever and cable were, this system seems like a very expensive high maintenance upD4
7th Jun 2014 9:32 am
Disco_Mikey
Member Since: 29 May 2007
Location: Dundee, Scotland
Posts: 20841
Incorrect adjustment and seized shoes are the main causes.
The motor winds the brass rod to it full extent of travel, and jams if left. The motor doesnt have enough torque to unjam itself.
An experienced ear can tell if it is winding too much when applied My D3 Build Thread
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
(Sorry) but doesn't a 2011 still have the red handle under the cup holders? If so I'm just wondering what you bent your shaft on !!!! ....So to speak.
up then.
