Advertise on DISCO3.CO.UK
Forum · Gallery · Wiki · Shop · Sponsors
  Home · FAQ · New Posts · My Posts · PMs · Search · Members · Members Map · Groups · Profile · Donate · Register · Log In  
DISCO3.CO.UK > Technical (D3)

New LPFP+HPFP+filter - Still 2290 and lose power on load
Post Reply  Down to end
Page 2 of 2 <12
Farmer Chalk
 


Member Since: 06 Mar 2013
Location: Independent Republic of Kentishshire.
Posts: 4196

England 2008 Discovery 3 TDV6 HSE Auto Tangiers OrangeDiscovery 3

Slight update…. Have now replaced the fuel rail using a genuine part which comes with the fuel pressure sensor affixed.. without tempting fate it may have fixed the issue.. car definitely responds differently and despite trying to provoke it to go into limp home mode over the last couple of days it is finally behaving..

I know this is too soon to be certain and I promise to report back…

It has definitely done something as the car now drives differently.. there is more of a very slight hesitation before giving you power when pressing the accelator so sensor is definitely telling the car to do something differently than before…

Keep you posted…fingers crossed!  
Post #237588425th Aug 2024 8:20 pm
View user's profile Send private message View poster's gallery Reply with quote
D1SCD
 


Member Since: 13 Feb 2013
Location: North Yorkshire
Posts: 440

United Kingdom 2005 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

I was about to try this today, as I have a very similar problem, but I don't seem to have a sensor Big Cry We're they not fitted to early engines, or am I looking in the wrong place ?


Click image to enlarge
  
Post #237607828th Aug 2024 2:16 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5061

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

On early (EU3) engines it is fitted to the diverter rail at the back of the engine with the HPFP. It is from this sensor that the high pressure fuel is monitored, and it's performance can be provisionally observed with a diagnostic tool. GAP>"live values">Engine>Fuel pressure. Do not use fuel rail pressure/sensor. yµ (idµ - eAµ) ψ=mψ

  
Post #237608328th Aug 2024 3:09 pm
View user's profile Send private message View poster's gallery Reply with quote
D1SCD
 


Member Since: 13 Feb 2013
Location: North Yorkshire
Posts: 440

United Kingdom 2005 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

Thank you PROFSR G. Do you mean that the sensor I have is different, and shouldn't be used in this location ?  
Post #237608428th Aug 2024 3:17 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5061

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

The original sensor does not seem to be available but there are other versions and aftermarket ones out there, all of which you take your chances with in terms of success.
If you want the original OEM sensor you have to buy the complete rail with the sensor already fitted.

What exactly is the problem you are trying to solve? The FRPS can cause problems if it's faulty, but, it does rarely fail so bear this in mind before you bite the bullet. You can get some idea of its operating performance by watching the fuel pressure fluctuations whilst raising the RPM, or better still whilst driving and watching the pressure under load.

The bare minimum for the injectors to fire is 150Bar and the max output of the HPFP is 1650Bar.
So at idle you should be seeing fuel pressure in the region of 230Bar with the VCV and PCV valves in the HPFP at approximately 21.87% & 13.67% respectively. The Mass air flow should be between 15 and 19 g/s. These values will obviously change according to load and rpm. Thumbs Up yµ (idµ - eAµ) ψ=mψ

  
Post #237608928th Aug 2024 3:45 pm
View user's profile Send private message View poster's gallery Reply with quote
D1SCD
 


Member Since: 13 Feb 2013
Location: North Yorkshire
Posts: 440

United Kingdom 2005 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

I occasionally go into limp mode under load. After watching the video earlier in this thread I thought for the price I would give it a go.  
Post #237609328th Aug 2024 4:12 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 5061

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

What are the fault codes? (include "Pending Faults) yµ (idµ - eAµ) ψ=mψ

  
Post #237609428th Aug 2024 4:19 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 2 of 2 <12
Jump to:  
< Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO3.CO.UK Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums
DISCO3.CO.UK is independent and not affiliated to Land Rover.
Switch to Mobile Site