Member Since: 17 Jan 2020
Location: Shrewsbury
Posts: 11
ah ok, ill give it another go.
And yes the numbers are full size.
I did read that it could be down to the reverse bulb? is this correct?D4 Barolo Black
31st Jan 2020 3:52 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4938
Doubt it but hey stranger things happen with these toysyµ (idµ - eAµ) ψ=mψ
31st Jan 2020 3:54 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4938
If you have the digits displayed correctly and reverse lights working then it's unlikely to be the XY, which is why I was suggesting diagnostics. yµ (idµ - eAµ) ψ=mψ
31st Jan 2020 3:58 pm
blakemore333
Member Since: 17 Jan 2020
Location: Shrewsbury
Posts: 11
So, just found out my reverse light doesn't come on. What does this mean?
Sorry if this has already been answered D4 Barolo Black
31st Jan 2020 8:48 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4938
If the bulbs are ok it's back to the XY sensor it seems. Diagnostics are your best move if you can't reset it manuallyyµ (idµ - eAµ) ψ=mψ
31st Jan 2020 9:58 pm
soylentgreen66
Member Since: 06 May 2020
Location: Staines Upon Thames
Posts: 3
EPB fault - of course!
Morning all.
For two days now my EPB will not release and I can't drive it anywhere. Message comes up as 'EPB Fault' on dash with the red and amber lights plus the sing song ding dong. There is no squealing, it just won't release! Very frustrating.
I have a 2007 SE automatic. Any help gratefully received!
2nd Jun 2020 9:28 am
JMack
Member Since: 02 Aug 2014
Location: Edinburgh
Posts: 1517
You may need to pull the emergency release cable.
This will release the park-brake, and you may be lucky that it will re-engage, but suspect you will need to re-wind and re-latch it.
Plenty of info available if you search.
2nd Jun 2020 10:03 am
soylentgreen66
Member Since: 06 May 2020
Location: Staines Upon Thames
Posts: 3
Great - thanks for the info. As long as I avoid even more expense on the damn thing!
2nd Jun 2020 11:51 am
Wibble12
Member Since: 09 May 2016
Location: Essex
Posts: 2
I was wondering if you managed to get you faulty EPB to release? I have the same problem now but mine is not down to it getting jammed up. I have had the thing apart more times than I care to swear about and it is now adjusted and running smoothly....until the other day when it would not release. I have a diagnostic tool and managed to get that to put it in service position so I could get home. It said it had a switch fault, I had a spare anyway that I knew was good so I swapped them over but still no luck. I am guessing it may be a wiring fault but just wanted to check first to see if anyone else had suffered similar and save me hours of prodding?
2nd Jul 2020 10:16 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 4938
What codes are you getting now?yµ (idµ - eAµ) ψ=mψ
I was wondering if you managed to get you faulty EPB to release? I have the same problem now but mine is not down to it getting jammed up. I have had the thing apart more times than I care to swear about and it is now adjusted and running smoothly....until the other day when it would not release. I have a diagnostic tool and managed to get that to put it in service position so I could get home. It said it had a switch fault, I had a spare anyway that I knew was good so I swapped them over but still no luck. I am guessing it may be a wiring fault but just wanted to check first to see if anyone else had suffered similar and save me hours of prodding?
I had a similarissue, it was realted to the swith, but the wiring going into the EPB itself, the outer insulation had split on two wire and the copper cable had corroded. 5 min repair and all good againSi
2016 Disco 4 SE Tech
2019 Fiesta ST3
2021 GBS Zero
3rd Jul 2020 12:02 pm
Wibble12
Member Since: 09 May 2016
Location: Essex
Posts: 2
Thanks fot that I will have a look tomorrow.
9th Jul 2020 8:50 pm
PotatoOfDestiny
Member Since: 04 Jan 2021
Location: Preston
Posts: 10
Hi, I'm really hoping someone can help me with an issue with my EPB. I've read through as much info as I can until my eyes have gone all boggly and fallen out but I can't see anything specifically to do with what I've done to my poor D3! Apologies if I've missed something that already answers this, but please point me in the right direction if I have.
I've recently replaced the brake discs, pads and handbrake shoes on my D3, however I failed to put the EPB into service mode first. Once everything was back together, I went to apply the handbrake, it wound on so far and then clicked a few times. I immediately realised my error and pressed the button down, which resulted in the handbrake winding off, but the warning lights coming on.
There has been no real screeching as is usually described, only a few fairly noisy 'clicks' and the handbrake isn't jammed on.
Can anyone give me any info on what might be required? (I'm hoping that if I've not done too much damage, I may be able to rectify this without rebuilding or replacing the module)
Many thanks!
6th Apr 2021 4:54 pm
aja4x4
Member Since: 14 Apr 2019
Location: Westbury
Posts: 2463
Did you follow Bodsys brake bible and adjust the shoes correctly? You can replace the shoes without going into service mode its just harder to do.Andrew
D3 2.7tdv6 2005
D4 3.0 SDV6 Commercial died and gone to LR heaven
D5 3.0 SDV6 HSE
6th Apr 2021 8:27 pm
PotatoOfDestiny
Member Since: 04 Jan 2021
Location: Preston
Posts: 10
Hi, yes it was Bodsy's brake bible that I was following, I *think* I followed it to the letter. It was only when I heard the gears clicking that I remembered reading about service mode.
It is however easily possible that I've messed up something on the adjustment when I've put everything back together, I'm a bit of a novice.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum