Member Since: 31 Dec 2005
Location: South West
Posts: 23830
Wheel Nut Torque
What amount of torque do the wheels nuts need to be tightened to?
I seem to recall the figure of 130, but can't find where I wrote it down
Thanks.
18th Jun 2008 12:58 pm
Pelyma
Member Since: 06 Jan 2005
Location: Patching, Sussex
Posts: 15496
I thought it was 140, it is in the manual - but I'm indoors supposedly working!DS3 TDV6 HSE - Silver with Alpaca (old one) Gone
DS3 TDV6 HSE- Silver with Alpaca (new one) Gone
D4 HSE Lux - Montalcino Red Gone
Porsche Cayenne V8 Diesel S
18th Jun 2008 1:23 pm
LT
Member Since: 31 Dec 2005
Location: South West
Posts: 23830
I'll check the manual later.
18th Jun 2008 1:26 pm
ronp
Member Since: 29 Nov 2006
Location: North Yorkshire
Posts: 15264
It's 140 Nm [+/- 10 Nm]...... always on the road less travelled 🚧
18th Jun 2008 1:45 pm
LT
Member Since: 31 Dec 2005
Location: South West
Posts: 23830
Thanks ronp.
I'm going to attempt my first DIY wheel swap, using my new air jack. Normally get my mates garage to do it, but there's no excuses now.
18th Jun 2008 2:09 pm
Davro
Member Since: 30 Jun 2007
Location: London
Posts: 352
I guess I am getting a bit paranoid about wheels, what with them being stolen, locking wheel nuts that may get stuck, uneven wear , unequal tread depths etc. Just to add to it, what do people do about the torque if you are stuck somewhere changing a wheel, do you just tighten it as much as you dare then limp home and get them checked, or do people carry torque wrenches around with them . If it is the latter , any reccommendations ?
18th Jun 2008 10:40 pm
DG Site Moderator
Member Since: 12 Dec 2005
Location: The Gaff
Posts: 50978
In general Davro very few peeps carry torque wrenches around with them ...just tighten to a stop ...then apply an additional firm push to stop again 21 year LR veteran > D2 GS 2003 > D3 S 2006 > D3 HSE 2009 > D4 HSE 2013 > D4 HSE 2015 > D5 HSE 2018 > DS HSE R-Dynamic P300e 2021
I carry an 18inch Draper extension bar with a six sided socket, without putting total effort into tightening I can easy get 140nm. It's just a matter of checking when I get home.
"I know that you believe that you understood what you think I said, but I am not sure you realize that what you read is not what I meant"
18th Jun 2008 10:49 pm
Pelyma
Member Since: 06 Jan 2005
Location: Patching, Sussex
Posts: 15496
I carry a torque wrench where the jack should go. I feel happier that I know they are tight enough before I drive off. I keep the Takla down the side of the dog cage so I do have a jack, just not the LR one.DS3 TDV6 HSE - Silver with Alpaca (old one) Gone
DS3 TDV6 HSE- Silver with Alpaca (new one) Gone
D4 HSE Lux - Montalcino Red Gone
Porsche Cayenne V8 Diesel S
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
I'll check the manual later.
