| Search results - "sell" |
My other 4x4443 viewsI'd sell my soul before I'd sell this one!
|
|
15 views
|
|
21 views
|
|
20 views
|
|
18 views
|
|
Thread upload18 viewsImage uploaded in new thread
|
|
14 views
|
|
14 views
|
|
16 views
|
|
Thread upload22 viewsImage uploaded in new thread
|
|
15 views
|
|
Thread upload18 viewsImage uploaded in new thread
|
|
15 views
|
|
Thread upload18 viewsImage uploaded in new thread
|
|
15 views
|
|
14 views
|
|
14 views
|
|
15 views
|
|
16 views
|
|
20 views
|
|
NEW REG PLATES29 viewsHi Guys,
I would like to buy these plates. they dont seem to sell them in the shop. Does anyone have any problem with me using the disco3.co.uk on the bottom of the plates. id rather do this as i do not want to add any stickers to my car.
d
|
|
Cat sells dog on ebay148 views
|
|
Part numbers for JAE connectors for the upper hatch switch. 379 viewsThis lists the JAE and Digi-Key part numbers for the electrical connectors for the hatch switch.
I contacted Japan Aviation Electronics and they directed me to Digi-Key in the USA who sell odd lots of the JAE product, odd lots meaning two pins and one connector if that is all you wish.
|
|
106 viewsFORD MOTOR COMPANY ANNOUNCES AGREEMENT TO SELL JAGUAR LAND ROVER TO TATA MOTORS
|
|
John Guest DOT all plastic fitting714 viewsThis is a picture of the John Guest DOT all plastic union. If you look closely, you can see the DOT imprinted in raised letters on the end of the fitting. This is of a 1/4" connector rather than the 6mm that the 3 requires.
The picture is similar to the air suspension pneumatic fitting union that Land Rover sells as replacement part # STC8580. This is for 6mm OD tubing size. The STC8580 comes with what are called "Collets" at each end that cover up the press to release feature underneath. See the John Guest web site www.johnguest.com under the Pneumatics section and also in Downloads for their catalog for install and remove instructions.
The actual "air brake spec" fitting that Land Rover provides has an interior 4mm OD ferrule that slips inside the 4mm ID of the nominal 6mm tubing. I have not yet been able to obtain the John Guest part number for the LR fitting, only the LR part number. This part number was generated for the RR Classic air systems.
|
|
John Guest (LR part # STC8580) push in straight 6mm tubing to tubing connector727 viewsThis picture is similar to the air suspension pneumatic fitting union that Land Rover sells as replacement part # STC8580. This is a 6mm OD tubing size push in to install straight tubing to tubing fitting. The STC8580 comes with what are called "Collets" at each end that cover up the press to release feature underneath. See the John Guest web site www.johnguest.com under the Pneumatics section and also in Downloads for their catalog for install and remove instructions.
The actual fitting that Land Rover provides has an interior 4mm OD ferrule that slips inside the 4mm ID of the nominal 6mm tubing. Hence the fitting depicted and part number are not actually correct. I have not yet been able to obtain the John Guest part number for the LR fitting.
The fittings that show in this doc are what I call food service fittings rather than transportation or Air Brake fittings. The part LR sells, (STC8580), is the Air Brake type for transportation.
|
|
Picture of old bus just prior to trading it in .... Jan 03 S model 35000 ish on clock - Had the infamous problem with liquid ingress on injector loom but after that was great car126 views
|
|
144 viewsmy best self indulgance after my D3
and shes a special limited edition aswell so never ever going to sell it
|
|
9 views
|
|
Thread upload4 viewsImage uploaded in thread 178758
|
|
56 views
|
|
85 views
|
|
Thread upload32 viewsImage uploaded in new thread
|
|
British Supermoto champs_Warden Law62 viewsIrish Champion & friend Greg Kinsella
|
|
|
|
|
|
