| Search results - "beam" |
Standard Vehicle Low Beam Lights Only (Bi-Xeons)32 views
|
|
full beam and HID spotlights70 views
|
|
D3 Bixenon dipped beam63 views
|
|
This is a normal H7 HID bulb installed in a BMW headlight to show glare above cut off line99 viewsThis is what the light pattern is that causes glare in most retofit applications including some projector lights. this is in fact a projector headlight on a BMW but the old projectors were only actually half projectors and half reflective bowls. the beam pattern should be clean cut like this ___/
|
|
Standard hid bulb - light everywhere and glare caused by light in bottom of bowl95 viewsWhilst the beam pattern is ok the problm is that with 300% more light the spillage into the bottom of the reflector bowl is seen as glare by other motorists. it also is the reason the overhead motorway signs are lit up so well be bad retrofit xenons
|
|
This is the Standard Hi-Beam only (Bi-Xeons)32 views
|
|
Thread upload6 viewsImage uploaded in new thread
|
|
Thread upload12 viewsImage uploaded in new thread
|
|
Thread upload9 viewsImage uploaded in new thread
|
|
Thread upload10 viewsImage uploaded in new thread
|
|
Thread upload8 viewsImage uploaded in new thread
|
|
Thread upload11 viewsImage uploaded in new thread
|
|
Thread upload2 viewsImage uploaded in thread 200614
|
|
Thread upload13 viewsImage uploaded in thread 138228
|
|
Not a pretty picture93 viewsWell, there had to be one of the beaming owner in the album somewhere.
|
|
Tap in to C2443 pin 3167 viewsC2443 pin 3 provides easy access to the high beam signal from MY14 onward. My13 and earlier the signal has to be taken from C583 Pin 34 (CJB)
|
|
Thread upload8 viewsR750...high beam mode
|
|
Lever to adjust the beam direction229 views
|
|
Wiring Diagram Fog Lamps76 viewsR130 is the (R5 relay under the hood) The wire is blue grey that is hot when the high beams are on and opens the relay contact that turns off power to the fog lamps. North America Only
|
|
Thread upload5 viewsImage uploaded in thread 166460
|
|
High Beams Main Beams Wiring Diagram76 viewsThis is the wire colors and connections for Dipped, Main, and Side Marker lights
|
|
7 views
|
|
Thread upload9 viewsImage uploaded in thread 152126
|
|
Main Beam - Xenons (non adaptive)103 views
|
|
Dipped Beam - Xenons (non adaptive)97 views
|
|
dip beam holder18 views
|
|
Back of main beam25 views
|
|
Spots + main beam110 views
|
|
No Spots Dipped beam110 views
|
|
Night All On Spots + Main beam136 views
|
|
Spots + dipped beam106 views
|
|
No Spots Main Beam only110 views
|
|
Intelli Beam Wiring Diagram312 views
|
|
H7 Upgrade ABD vs philips standard main beam only HIDS4U85 views
|
|
CALENDAR 201185 viewsTaken in Beamsley nr Skipton, North Yorkshire
|
|
philips d1s ultrablue upgrade hid xenon bulbs hids4u79 viewsThese bulbs have a whiter light than standard and a blue coating gives a blue tint from a distance and at the edge of the light beam when parked against a wall.
|
|
Next I will install additional high beam lights317 views
|
|
Switch for Hella 4000 Compacts303 viewsDriving lamps are integrated with the high-beams or can be overriden with this switch.
|
|
Philips D2S 85122 C1 Xenon 4300K projector HID bulb962 viewsThis is the 4300K OEM bulb in our HID Xenon projector headlights. People who design illumination systems regard the 4300K colour as a good compromise to provide what is called definition. This is effectively the ability to actually determine what an object being illuminated probably is. The more blue colour bulbs, say 5000K and greater, result in a reduction in the ability to distinguish detail, (regardless of brightness), of the object being illuminated. Effectively, you can see the object but you cannot quite figure out what it is. This is because the more blue frequencies means there are fewer other frequencies of light that allow our eyes to actually discern what an object really is.
The 4300K colour temperature applies to clear air conditions; for rain, dust, snow, fog, etc, then a yellow 2500K colour temperature is preferable. 2500K provides more contrast and there is less back splash of light off the air particles. In blowing snow, this means less sparkle back. Flat top cut off of the light beam, (which is the pattern our projector lights have), is important to reducing back splash - hence you do do not want roof mounted lighting for adverse conditions - as low down as possible is preferable, (which is why fog lights generally sit low.)
|
|
s7153 viewss7
|
|
Thread upload13 viewsImage uploaded in thread 150660
|
|
Thread upload8 viewsImage uploaded in new thread
|
|
|
|
|
|
