Search results - "WA" |
In Jordan wady Ram90 views
|
|
RRSport Auto TDV6 0-100-0 times and G Forces156 viewsAir Temp 18, Dry conditions.
Best Acceleration G was .785 and decelleration G was 1.55
|
|
The full complement of bits and pieces, major parts back from the powder coaters, all bolts nuts washers replaced with stainless steel241 views
|
|
0000 LR Bluetooth dealer Kit install instructions1609 viewsThis 17 page pdf is mostly a series of pictures showing how to install the original Land Rover dealer installed Bluetooth kit for circa 2005 / 2006 three's. Also included are three wiring diagrams sheets related to the pairing code 0000 Bluetooth install.
This pdf is useful if you are now removing the 0000 kit to install the optical 2121 MOST D4 module, an easier install than the 0000 kit ever was.
|
|
Ken and Slimer tried to steal parts whilst no one was looking!190 views
|
|
51 viewsD44 front winch bumper. Ali washer bottle. D44 rear h/d bumper. centre diff lock. 235x85x16 pirelli muds. OME +2" springs & shocks. front diff guard. side tree bars. wired for roof CB. Aux fuse block. safari snorkel. extended wading tubes. the list goes on...
|
|
Fog Light & Washer Jet Install93 views
|
|
Fog Light & Washer Jet Install94 views
|
|
202 viewsDidn´t loose contact, but grip was zero.
|
|
01 D3 on Train183 viewsEasiest method of crossing 2300 km of Nullabor Desert - on the Indian Pacific train. D3 with trailer - effectively have 5 spare tyres if it really gets desperate!
|
|
01 Start of Xmas 07 trip across the Australian Nullabor243 viewsThis is the preferred method of travelling 2500km of Nullabor desert when time is short (the Indian Pacific train). Next stop is Adelaide.
|
|
Rimozione pannello dalla sponda - Tailgate panel removing45 viewsPer togliere il pannello moquettato dalla sponda ho fatto leva con un cacciavite abbastanza grosso nel punto indicato, è stato veloce e non ho rovinato niente.
To remove the carpeted panel away from the tailgate I used a big enought screwdriver at the point indicated, it was fast and I have not ruined anything.
|
|
Mitsubishi Montero Headlight Washer43 views
|
|
How fast?231 viewsI was driving along the Autobahn, glanced down at the speedo which was showing 140 mph, the Tomtom was telling the truth at 132 mph, but by the time I had switched the phone to camera I had dropped 2 mph, didnt try and do it again as there was no need.
|
|
The wet Walk from the pub71 views
|
|
Everyone heard that DG was at the bar161 views
|
|
200 viewsSuzuki Jimny. Some holes were deep enough to swallow the little fella, but it got out as long as all wheels were on the ground. No difflocks or electronics in this one.
|
|
Got Married!241 viewsOccasionally the car does get a clean/polish, this was a special occasion :-)
|
|
CALENDAR ENTRY 20091191 viewsBonatti grey TDV6 S, ambulance conversion, MTR's, winch, RAI, safety devices roof rack, rear ladder, bash plate, warn lighting, LED lighting throughout.
Owned by me, Rich Bell, Director of Extreme Medical Ltd, providers of medical support to Land Rover events.
|
|
02 On banks of Darling River, Back of Bourke158 views"Back of Bourke" is the typical definition of the start of the Australian Outback. This was after crossing the Darling River "back of Bourke" on 8 Jan 08. We were the first vehicle to start driving after floods had closed (first time in 8 yrs there was any water in the river).
|
|
02 Last Photo before the little wheel problem saga222 viewsThis is my D3 with trailer on the banks of the Darling River, literally "back of Bourke" (the regional definition of the start of the Australian Outback). We were the first vehicle in a week to try and drive this route from Bourke to Wilcannia on the account of floods (first water in 7 years). Little did we know that 3 hours later there\'d be a bit of a wheel and tyre problem appearing...
|
|
Tagliare lungo il perimetro della chiave - Cut along the key perimeter17 viewsI gusci sono saldati ad ultrasuoni. Con il disco tagliare lungo il perimetro della chiave in corrispondenza della giunta: lo spessore è di circa mm.3. Io non sono andato fino in fondo per evitare di danneggiare qualcosa, una volta inciso il solco per mm.2,7 ho fatto leva col cacciavite e ho strappato il materiale restante.
The body is ultrasonically welded. With the disc cut along the perimeter of the key in correspondence of the joint: the thickness is approximately 3mm. I have not gone all the way down
|
|
This is why the bus was canceled!39 views
|
|
Truck Back 90 Challenge truck spec in the water53 views
|
|
That WAS steep!138 views
|
|
Silverstone Classic Media Day177 viewsAttended the media day for the Silverstone Classic, took 3 cars to display & tell 300 journalists what we do at the show.
David Coultard was one of the drivers who were taking the journalists around the track.
|
|
114 viewsboth adapter the larger one needed a bit chopped off the botom and the washers to fit
|
|
127 viewsleft hand adater adopted, decided right hand adapter was ok but right hand one fits and is stronger
|
|
03 First bit of tyre/wheel trouble245 viewsIn the outback a tyre suddenly blew. "No worries" we thought, as we had 3 spares (+ two more if we abandoned the trailer), 150l of water, 3 days of food, and an EPIRB if things got really bad. At the time I didn\'t fully appreciate the fact that my index got a blister from the burning heat of one of the wheel nuts. It was 45 deg C at the time, so everything was hot.
|
|
03 The first bit of tyre/wheel problem251 viewsSomewhere in the Australian outback on a 45 deg C day in Jan 08, a D3 had a bit of a flat tyre problem. "No worries, mate" st we had 3 spares (plus 2 more if we abandon the trailer), 150l of water, 4 days of food, and an EPIRB if things really go crook. The first clue that this was not a "normal" flat was when I handled a wheel nut and ended up with a blister from a burning hot nut (the ambient wasn\'t THAT hot).
|
|
04 Damaged Tyre301 viewsYes, there\'s no doubt that this was a flat tyre. The ultra hot wheel nuts, look of the flat (note in a later photo that the back of the tyre appeared okay) and increased fuel consumption should have been a clue, but it was 45 deg C, and we had been doing about 105 km/hr on a dirt road for hours, so we just assumed it was a flat = WRONGO!
|
|
Thankfully it\'s nearly a week old. they wanted to dig underneath my drive to install gas. Nov 5th, Bang,78 viewsNo, and i was worried about the rangerover!
|
|
really sticky mud173 viewsCan\'t really see it in the pic, but off the road the mud was treacherous
|
|
Here it is - long awaited Mantec plate in action directly after being installed! Thanks again John!!!169 views
|
|
05 No doubt the tyre is flat275 viewsThis is the view of the flat tyre. Again, didn\'t think it anything more than a "normal" explosive blowout, as the tyre was about 90% worn, we were heavily loaded, it was 45 deg C, and driving 105 km/ho on a rough dirt road in the outback.
|
|
Seriously....anyone want to mess with that bumper71 views
|
|
Wating in line42 views
|
|
06 Spare tyre on and still suffering from hot wheel nuts296 viewsManaged to get ultra hot wheel nuts back on the spare (using the original 19" D3 wheel, vs the 19" RRS wider wheel which blew - shown in left of photo). Pity we didn\'t note that the disk brake was EXTREMELY hot at this time.
|
|
The biggest Defender in the world?166 viewsSeen at Zwartkops raceway a couple of weeks ago
|
|
07 Back side of failed tyre340 viewsThis is the back of the blown tyre. It looks like any other worn tyre which has run a bit while flat. Note that we were running on wider 19" RRS wheels (have 4 19" MTRs + 1 old A/T on the original 5 wheels). Also have a rear-mount spare tyre holder which is really convenient with the wider rim and the fact that the tyre was still hot (it had some melted rubber on the other side!!)
|
|
Spot lights 183 viewsFinally there was light
|
|
A green haven in a vast expanse of lava21 viewsThis was a great place fore some mid day leg stretcher and lunch
|
|
Watching puffins at VÃk20 viewsGreen cliffs with the black lava sand beach as backdrop.
|
|
Thread upload17 viewsImage uploaded in thread 155142
|
|
Lake Eyre with water in 2000 79 viewsTook a flight from William Creek to view the lake with water in it.
|
|
08 D3 stranded with a seized smoking wheel315 viewsAbout 1 hr after replacing the blown tyre, strange noises emanated from the stability control system and speed dropped off. Then I looked in the rear view mirror, and noted a cloud of dust along with a whiff of black smoke. This led to a very quick stop (no traffic on this route for over a week, so no worries about having to signal exiting the road). Took a look and WOW. The right rear wheel was glowing a dull red colour, and burning rubber smoke was wafting from the red glow over the fuel lines.
|
|
D3 in Southwater170 views
|
|
DickieDisco avoiding water...49 views
|
|
DickieDisco trying to decide if this is a better way down...48 views
|
|
Sensor bar33 viewsSensor has been moved out to tire carrier where it should be. It does not pick up the tire anymore. "no faults".
|
|
Highlift mount added27 viewsHighlift mounted in this position allows for any length with out overhead clearance issues if stood upright
|
|
highlift and new sensor wire loom30 viewsNew wire loom added to protect sensor wires and keep things sanitary looking
. Highlift jack mount arms added and gas strut
|
|
New mods for carrier. Backup sensor moved to the tire carrier. Toy rack and highlift mounts.38 viewsSon wanted all the toys on the carrier. I just wanted easy removal for a good clean look.
|
|
This is how to make it all work. Backup sensor on carrier43 viewsHighlift, ax and shovel. Yes they are matching colors. What else?
|
|
09 Starting to remove the seized brake assembly296 viewsBy this time we\'d poured about 8l of water on the dull-red glowing and burning wheel assembly (too close to 140l of 98 octane petrol). Sudden cooling cracked the disk brake which showed mangled park brake parts. How to remove a brake disk without the right star fitting? First remove the caliper then get a sledge hammer?!!
|
|
Transmission as it was.89 views
|
|
COVER SHOT FOR TOTAL OFF ROAD114 viewsG WAGEN AXELS FITTED WITH HYDRAULIC FRONT + REAR DIFF LOCKS + EXTREAM SUSPENSION SYSTEM FRONT + REAR WARN WINCHES.
|
|
Receiver for toy rack39 viewsSensor bar was made of same heavy tube that the carrier was made from allowing a small 1 1/4" receiver to be placed on it for a multitude of toy racks of my choice. Rack adjust in and out of receiver.
|
|
car wash282 views
|
|
Plenty of water crossings..125 views
|
|
Harvey tiles and the 7 Dwarfs!119 views
|
|
Thread upload2 viewsImage uploaded in new thread
|
|
Thread upload4 viewsImage uploaded in thread 197728
|
|
wax49 views6
|
|
10 Cracked smoking parking brake drum338 viewsNote the crack in the face of the brake. This showed mangled parking brake springs and other bits. Also a bit of melted rubber was drooling out of the crack. Started to remove the brake caliper and enjoying the flies in 45 deg C heat. Ah, the wonderful Aussie climate in January.
|
|
Solar Water heating149 views
|
|
Repositioned compressor bracket737 viewsThe bracket was snapped in two, so I had it re-welded and slotted out the mounting holes so that it could be positioned 10mm higher (no longer protrudes under the chassis rail)
|
|
off-camber hill352 viewsAnd no, I wasn\'t hanging my arm out to balance the car - I was stopped at this point waiting for the Jeep in front to try and finish. It was a pretty steep off-camber slope!
|
|
Last hill climb247 viewsA lot steeper (and slipperier) than it looks!! On the way to a Class A nad B win.
|
|
Rally Wales 2008 200 views2009 G4 now with black RRS wheels lightforce lights and strobe lights in bumper and rear lights
|
|
Strata Florida Dec 2008 way home after Rally GB103 views
|
|
George Washington National Forest 2008154 views
|
|
George Washington National Forest 2008139 views
|
|
Rich waving a wheel march 201177 views
|
|
bit of water70 viewsdidnt think it was so deep. I got my feet a little wet. Car is still running and it also survived this and is still in use now. Bet a Disco 3/4 wouldn't work after this.
|
|
What was left26 viewsThe bitty which was left attached to the hub when the wheel failed whilst driving
|
|
Well 12 , good water198 views
|
|
Ahh.... Yes there IS water down there217 views
|
|
Savoury Creek, crossed it further down where there was minimal water204 views
|
|
We think it was a Toyota Prado263 views
|
|
Fuel truck was in on day we were there259 views
|
|
This picture was taken with garage doors closed.43 views
|
|
Jack Smiths grave, a stockman who died in his swag333 views
|
|
This guy has been waiting for a long time437 views
|
|
201 viewsRemoval of Intercooler hose, don't forget to plug the hole, don't want anything to fall in there
|
|
in the snow233 viewsdiscovery doing what it does best working in the snow
|
|
The Discovery Family33 viewsDiscovery 4 & Discovery Sport (My son soooo wants a Disco Sport!)
|
|
Yup, it was cold!! Water in kettle froze during the night..124 views
|
|
Katse dam... 50Km drive to dam wall!132 views
|
|
11 Lesson in removing a jammed brake assembly in the Outback378 viewsSpent the next 4 hours doing this to my D3. Gave the photos to Land Rover dealer and they did not think this constituted abuse of the vehicle. I thought that was charitable, but if we hadn\'t done this, the tow back to civilisation would have been even longer.
|
|
Walk in the park357 views
|
|
Hardware384 views
|
|
110 at Carinya Escapes ,Flinders ranges295 viewsDefender 110 Extreme,Long Range fuel tank,under floor water tanks, HF radio,GKN Overdrive,Swingaway Spare Carrier,70 litre Freezer,30 litre Fridge,Roof top Camper,Cruise Control,
|
|
182 viewscame loose when washing car with power washer - its 15" long and hollow
|
|
Kuwait Land Rover277 views
|
|
Muddy LR3 at US SUV of the Year Awards3659 views
|
|
Half-way through421 views
|
|
12 Half way through removing a jammed disk brake in the Outback296 viewsThis was just before breaking the sledge hammer. Note we luckily carried a spare hammer. Ended up using (or breaking) every tool we had on this little repair job. Bed sheets are a good way of gathering the bits to show for the inevitable warranty claim.
|
|
Walking out after getting bogged - half way!55 views
|
|
12220 viewsThe boot cover is back in place, hiding away all the controller components.
|
|
13 How to care for tools303 viewsWhat happened to the sledge hammer after 2 hours of beating my seized and cracked disk/park brake assembly to bits. Now down to 1 hammer remaining. At least by this time it was getting cooler (down to 40 deg C)
|
|
Owen Springs - Towards the West MacDonnell Ranges161 views
|
|
Virgin Snow134 viewsWent for a play in some new snow so I could practice and get my driving style right on close to zero friction surfces. Hard to tell from this photo, but car is parked on a 1:6 slope heading uphill, with hard packed ice under the fresh snow covering. I stopped here to practice my hill starts on ice...I was there for some time :)
|
|
174 viewsWALES MARCH 08
|
|
162 viewsWALES MARCH 08
|
|
honestly officer....if it was overloaded, it would be sitting on the rear axel ??? heh heh79 viewsfunny how some cops will accept what their eyes tell must be the truth, a trailer load of logs home ....easy peasy, hahahahaha
|
|
Yarwell Shallow Water 276 views
|
|
156 viewsWALES MARCH 08
|
|
nice and warm next winter65 views
|
|
Thread upload17 viewsImage uploaded in thread 70979
|
|
15 First sign of bits of parking brake failure336 viewsNote the complete lack of pad from the parking brake. Not only was there no composite brake material left, but the drum was somewhat twisted and connecting bits all smashed. Also a small drip of melted rubber from wheel bearing parts....
|
|
Border Rover in Boughrood,what can i say,It was an Amazing Weekend.51 views
|
|
Bull Dust - Old Andado Track on way to Santa Teresa79 views
|
|
In Disgrace100 viewsThis is where its been for 3 weeks &3 days waiting for the parts to arrive from England. later that afternoon we aere able to take her home. Civilation at last :)
|
|
A De-restricted Bridleway,Well done Hampshire CC9 views
|
|
Bird River road - old railway cutting367 views
|
|
16 All the remains of a D3\'s parking brake373 viewsAfter 4 hours of hammering, finally removed the disk/park brake drum, and nearly all the parking brake bits fell to the ground. Cut rhe remaining brake cable loose as it was wrapped around the hub and a bit melted. Also having 2 jacks + 2 jack stands will support 4 hrs of hammering on the side of my D3.
|
|
fuel range????????296 viewsfilled tank up and climbed the 21 hairpins into Alpe d\'Huez 1860m - as you can see the projected fuel range (due to the climb) suffered. The reality was different as it used virtually no fuel on the descent.
|
|
Do Not Park Trucks On Railway Lines!182 views
|
|
A5 towards CApel Curig48 views
|
|
261 views
|
|
221 views
|
|
207 views
|
|
199 views
|
|
18 Brake "repairs" finished at sunset296 viewsWe just finished the repair at sunset and were driving slowly with 3 brakes. Oddly the D3 didn\'t behave any differently at 50 km/hr than it did normally. We had 4 instances of hitting the (3) skids for kangaroos before arriving in Wilcannia 3 hrs later. The brake light warning was making very distinctive noises and flashing randomly, though.
|
|
Thread upload9 viewsImage uploaded in new thread
|
|
Damage from Mud plugging on way to Barston Ford183 views
|
|
Mud plugging on the way to Barston Ford173 views
|
|
Suspension dragster mode442 viewsAfter I succesfully changed my wintertyres to summertyres, I found out that the front suspension was on access level and rear at off-road. Situation cleared after I switched engine on.
|
|
What the weekend was all about41 views
|
|
Thread upload17 viewsImage uploaded in thread 164848
|
|
Looking out over Kielder Water11 viewsLooking out over Kielder Water
|
|
Looking out over Kielder Water16 views
|
|
Looking out over Kielder Water107 views
|
|
D4 HSE on Grasshill Causeway107 views
|
|
The Water Cut Mallerstang126 views
|
|
D4 & D3 On Grasshill Causeway22 views
|
|
D4 HSE on Grasshill Causeway in the snow43 views
|
|
D4 HSE on Grasshill Causeway190 views
|
|
D4 HSE on Grasshill Causeway120 views
|
|
D4 HSE on Grasshill Causeway208 views
|
|
D4 HSE on Grasshill Causeway27 views
|
|
D4 HSE on Grasshill Causeway in the snow166 views
|
|
D4 HSE on Grasshill Causeway25 views
|
|
The view from High Tilberthwaite31 views
|
|
At the water Cut on Lady Anne's Way above Mallerstang34 views
|
|
D4 HSE on Grasshill Causeway in the snow187 views
|
|
On Grasshill Causeway72 viewsA selection of D3's, a D4 and a couple of Defenders on Grasshill Causeway the highest greenlane in the UK
|
|
On Grasshill Causeway 319 viewsA selection of D3's, a D4 and a couple of Defenders on Grasshill Causeway the highest greenlane in the UK
|
|
Rudland Rigg49 viewsThe view from the top of Rudland Rigg looking out towards Roseberry Topping and the coast.
|
|
Green Lanning in Cumbria 2012 Calendar326 viewsTaken next to "The Watercut" on The Old Highway above Mallerstang in Cumbria
|
|
Kingmav in the water36 views
|
|
Standard hid bulb - light everywhere and glare caused by light in bottom of bowl95 viewsWhilst the beam pattern is ok the problm is that with 300% more light the spillage into the bottom of the reflector bowl is seen as glare by other motorists. it also is the reason the overhead motorway signs are lit up so well be bad retrofit xenons
|
|
WAX53 views5
|
|
Thread upload7 viewsImage uploaded in thread 137258
|
|
Thread upload7 viewsImage uploaded in thread 137258
|
|
Thread upload8 viewsImage uploaded in thread 137258
|
|
Area of the new housing expansion south of Swindon.144 viewsFlood plains will be flood plains - insurance anyone? Oh sorry forgot; all top 8 insurance companies refused to insure a house in this area, so the developers are going ahead building anyway...
|
|
Badbury to Wanborough road141 views
|
|
166 viewsFloating bridge Linyanti Swamp Caprivi
|
|
Washer Bottle Bracket878 views
|
|
EEEE-Neee, MEEEEN-Neeee, MY-Neeeee, Mo....... DISCOVERY IS THE WAY TO GO!106 views
|
|
D3 in the Mary River Flood plains47 viewsIn this part of the world, on the flood plains out to Kakadu, you never get out to wade a creek first as the theory says you should. If the water isn\'t clear, like it was on this causeway, and it is this wide, you either wait for someone else who is braver than you to cross first, or you turn around and go home. These rivers are full of estuarine (salt-water) crocodiles, and they are starting to reach 7 metres in size in some still rare instances. However, seeing as a 2.5m crocodile can kill a grown man,
|
|
D3 in the Mary River Flood plains50 viewsFamily was down South with the In-laws, so I went for a drive on Boxing Day - which is the monsoon time, or \'The Wet\'. Was doing a test run with the off-raod trailer in preparation for the trip I was planning to the Kimberley six months later. Couldn\'t quite make it out of the creek, so a self-recovery was in order. Good thing it all worked, as I didn\'t see another car in over four hours. They were too smart to drive down the track I was on!
|
|
2009 Ford ESP Extended Warranty Contract144 views
|
|
D3 in Kakadu National Park, on the track into the Alligator Billabong47 viewsThis whle area is down on the flood-plain, so in the Wet it is all under a few inches of water. In the dry it has a hard but brittle surface, which is then chewed up in many places by the feral animals with hard hoofs such as buffalo, pigs and horses. This then turns the track into a big dust bowl which is primarily bull-dust - a soft fine powder like talcum powder, which can be many feet deep, and gets into everything. The cover on the trailer is actually black.
|
|
65 viewsBroome WA
|
|
Local WA newspaper article on D3 Theft168 viewsThe article is info by police public affairs. They wanted something to keep people locking doors and taking care during the holiday period. There are also TV public service announcements on air in WA featuring my wife confessing to leaving 1 door unlocked leading to the theft.
|
|
Waiting for a D1 to pass in the Goyt Valley67 viewsStopped to let a D1 and his vectra-in-distress pass on the main slope down to the reservoirs in the Goyt Valley
|
|
Frozen water fall (sort of) in Goyt Valley68 views
|
|
Waiting for ferry130 views
|
|
Salt Water Croc - at base Bloomfield Falls, Wujal Wujal Cape York20 views
|
|
Kalpowar Crossing Camp Ground - Litchfield NP Cape York23 views
|
|
What water does to the Desert - near Bedourie QLD20 views
|
|
'Big Red' sandune with water!! - Simpson Desert 23 views
|
|
This was Australia's largest Shearing Shed - Cordillo Downs SA26 views
|
|
121 viewsTraxide brain mounted. It's mounted slightly tilted towards the front of the engine bay so as to give as much space as possible to the brake vacuum pipe behind it.
|
|
120 viewsModified aux battery box cover with shape of battery to battery cable. I also removed the tab which was fouling my traxide brain mounting bolts.
|
|
94 viewsReverse wire stripped. I then soldered the wires which I need to this wire and close up with self amalgamating tape. This way I don't damage any original wires (except for the insulation) and it's easily reversible by desoldering
|
|
91 views12V socket done. This is permanently powered by the Aux battery. Another one was done on the other side, though that one required drilling the hole with a 29mm hole saw as there wasn't an unused hole on that side.
|
|
112 viewsDue to the side terminals protruding out the side and affecting the battery clamp, I found the battery will fit better if it could be pushed a few millimeters towards the engine. This lip will have to be removed.
|
|
BlackVue DR40032 viewsA still from the first clip (before the date was set), good picture quality.
|
|
18 viewsjust washed her
|
|
waterproof connector for connecting camera on trailer 52 views
|
|
waterproof connector for connecting camera on trailer 48 views
|
|
waterproof connector for connecting camera on trailer 50 views
|
|
watefall18 views
|
|
motorway19 views
|
|
off highway roads get worse20 views
|
|
new highway...soon21 views
|
|
Bee-sting 1/4 wave VHF antenna25 views
|
|
ta-dah! the final result36 viewscomplete GPS satNav system, with iGO software and ALL maps from europe 2012, including POIs speedcams, and personalized land rover skins
|
|
First trip in the snow225 views
|
|
Side Step Bars Tubes with footstep244 views
|
|
Side Step Bars Tubes Tinted Windows378 views
|
|
My Disco 4 HSE32 viewsUnwashed...blame outdoor LHR T1 2 week parking!!
|
|
My D3201 viewsJust washed and polished.
|
|
big jeep28 viewswent to collect my optima battery...this was in getting a new wing fitted
37" wheels are quite big...
|
|
Winter waxing done203 views
|
|
TravAll Dog guard installed and waiting for passengers165 views
|
|
146 views
|
|
D3 First Wash42 views
|
|
185 views
|
|
At work shining in the sunsheeeine181 viewsWashed it last night and applied Permanon Car Supershine Nano coating
|
|
what plant22 viewswant to find out what this plant is and how best to control / remove it from garden
|
|
rainbows19 viewswalked past this....side "vents"also tricolour.
|
|
Thread upload132 viewsSplit after removing duck tape. I think the split got longer whilst waiting for new silicone hose's to arrive.
|
|
Jänschwalde offroad0 viewsTenTipi safir9 with stove
|
|
Thread upload0 viewsImage uploaded in new thread
|
|
Thread upload5 viewsImage uploaded in new thread
|
|
Thread upload12 viewsImage uploaded in new thread
|
|
Gospel Pass Jan 2015146 viewsThe Gospel Pass (Welsh: Bwlch yr Efengyl) is the highest road pass in Wales. It is at the head of the Vale of Ewyas in the Black Mountains of southeast Wales.[1] The narrow mountain road climbs steeply from Hay-on-Wye to a height of 549 metres (1,801 ft) [2] above sea level, squeezing between the mountains of Twmpa to the west and Hay Bluff to the east, before dropping down into the valley to the south on its way to Llanthony Priory, Llanfihangel Crucorney and Abergavenny.
|
|
solar panel install356 viewsAt least at this point, I mounted it by using Clear Silicone RTV. This stuff is kind of like glue, but can be removed. If it doesn't hold up after curing and driving, I'll remove it and come up with another plan. I used heavy cable ties on the 4 grommets, in case it lets loose, it won't take out my wiring and the car behind me. 2 Panels are dandy like this, but I don't want to permanently block the roof space. Grape Solar to power my snomaster fridge
|
|
low profile solar panel211 viewsThe low profile solar panel, can be seen here, as the fine white line under the light bar. The way it's laid out, the panel should generate decent power between 10am and 4pm depending on the time of year, from the sides or front, with no shadows. Grape Solar 100W flex panel.
https://www.facebook.com/DifferentialPartsUS
|
|
Traxide USI-160 Install515 viewsOverview picture of Traxide USI-160 upgrade install. This was an upgrade from the SC80 which performed flawlessly. The USI-160 had two relays and can deliver more amperage. As a result, the wiring was upgraded to 4/0 Welding Cable (warn) and heat shielding was added. The unit performs flawlessly to support 2 HAM Radios, Fridge, etc. Like me https://www.facebook.com/DifferentialPartsUS
|
|
Winch Power upgrade318 viewsUsing 2 warn kits, and removing one of the wires to use on another project. The purpose was to replace the power and ground wire. I used Warn kits, which are 4/0 Welding cable. The original red #4 warped from getting a little too worn. The 2nd
Battery #1 Deka 9A94 AGM Intimidator, Battery #2 Deka 9A47 AGM Intimidator WARN 36080 28" Quick Connect Cable X 2, WARN 26405 Quick Connect Cable 7' X 2, WARN 15901 Black Cable X 1 -- winch control 72" X 1 https://www.facebook.com/DifferentialPartsUS
|
|
Black Yatt134 views
|
|
Marine Plug346 viewsRunning a cigarette plug rated at 15a with a plug rated at 20a drawing 5a at 12.8v will generate more heat than you want. Use Anderson or hardware.
|
|
screen wash supplies13 viewsnever enough screen wash when family run 3 in winter
|
|
Watch what's behind you!21 views
|
|
End of the runway :-(15 views
|
|
Thread upload5 viewsImage uploaded in thread 182161
|
|
Thread upload0 viewsImage uploaded in thread 5
|
|
Lunar Ultima hitched to Disco 411 viewsPulling away for another caravan adventure
|
|
113 views
|
|
83 views
|
|
new parts waiting to be installed2 viewsImage uploaded in thread 177818
|
|
Thread upload22 viewsImage uploaded in thread 184721
|
|
Thread upload22 viewsImage uploaded in thread 184721
|
|
Thread upload23 viewsImage uploaded in thread 184721
|
|
Thread upload1 viewsImage uploaded in thread 192575
|
|
As it was when I had hd enough at night, next day to wire in HF antennae293 views
|
|
I knew it was special the moment I saw it.349 views
|
|
Area where Alarm Sounder was originally fixed99 views
|
|
Home sweet.... where are the walls?108 views
|
|
Wating for the proffessionals!45 views
|
|
Journey home4 viewsOur first journey on our way home to France
|
|
Land Rover Stop Tail Light dual filament bulb nominal 12 volt 21 / 5 watt filaments1427 viewsThis is the Land Rover part number 264590 dual filament bulb, (P21/5), that inserts into the upper two tail lamp receptacles. In the upper one, both filaments function, in the lower one, only the 5 watt tail light filament functions.
I regard it as not a good practice to routinely switch bulbs when the tail light filament, (5 watt), burns out on the lower bulb. The broken filament can jiggle over onto the brake light filament, (21 watt), and short the circuit to ground or something else not predicable.
There are also arguments to say that quality control is better on the Land Rover marketed bulbs than say far east sourced bulbs. Filament construction, and hence resistance can vary and mislead the current sensing circuits monitoring the signal light systems. Also when the bulbs are properly installed, all filaments should be standing vertically and not at any slope.
These are the sort of obscure circumstances that can lead to false trouble messages on the display, dropping to the stops, and subsequent concerns - all over a tail/signal light bulb.
For example, the filament life of both the tail light and the brake light filaments in the P21/5 bulb is significantly less than the USA common 1157 dual filament bulb, (1000/250 vs 5000/1200 hours); brightness in the P21/5 is a bit more, (3cp/35cp vs 3cp/32cp where cp is candle power), but current consumption is oddly less, (0.44a/1.86a vs 0.59a/2.10a where a is amps). It is the quest for efficiency vs maintenance trade off.
|
|
Thread upload47 viewsImage uploaded in thread 102519
|
|
New front bumper with headlamp washers, fogs and PDC complete110 views
|
|
290 views
|
|
299 views
|
|
Thread upload7 viewsImage uploaded in thread 121845
|
|
Thread upload3 viewsImage uploaded in thread 121845
|
|
just washed..:)175 views
|
|
You just pull over and wait - Gibb River Road93 views
|
|
Water Pipe - solid77 views
|
|
Charge Air Pipe - turbo end.101 viewsThe maint manual identifies releasing the pipe hose clip in the center of the photo. Pity who ever built this engine Put the hose in such a position that access to it was near impossible. I released the other clip at the turbo end of the flexi hose. Easy to get to but a right git to release the hose of the turbo.
|
|
Air con pipe65 viewsIts the brown pipe in the center of the photo. To remove this first you need to remove the "charge air cooler inlet hose" to allow access to the air con pipe securing fixings. But with the "charge air cooler inlet hose" disconnected it can\'t be removed from the veh because the air con pipe is in the way???
|
|
Well and truly stuck on a green lane at the weekend, there was a hill that does not show up in the photo!273 views
|
|
2 90's off at Lochearnhead208 viewsGuess this was why we turned round.
Photo pinched from SLROC website!
|
|
wax60 views4
|
|
_DSC0206208 viewsNice bow wave!
|
|
Pure Highway 300di37 views
|
|
ZF 6HP26 Transmission Cooling System Description and Operation2936 viewsThe five page pdf details the operation of the cooling system as related to cooling engine oil, transmission oil and providing hot water to the cabin heating system.
|
|
Headlight washer plugs83 views
|
|
bottle with H/L washer pump and leveling sensor to the right - the space on the far right is for the w/screen pump87 views
|
|
Headlight washer hose85 views
|
|
Carwash20 viewsThis seems a long time ago - down on the east coast of Oman
|
|
_DSC0211197 viewsD3Matt's water wings
|
|
Creek crossing on way to Sandy Creek Falls - Litchfield NP113 views
|
|
Rasta 4x4 Swing away spare wheel mount115 views
|
|
The Waterfall54 views
|
|
Mud/rock scrapes.177 viewsWhat happens when you lean the car on a mud wall.
|
|
Damage closeup 1150 viewsWhat happens when you lean the car on a mud wall.
|
|
Leaning163 viewsThis is an example of the leaning against the mud walls.
|
|
Mud walls157 viewsMost of the trip!
|
|
Thread upload4 viewsImage uploaded in thread 196028
|
|
Three Way Pylon75 views
|
|
Billing Off-Road Course Water Splash43 viewsLottie\'s first off-road experience at the Billing off-road course with MikeS providing some vital guidance!
|
|
video proc73 views
|
|
4-20200928_Vigor166_Firmware_Upgrade16 views
|
|
wax65 views3
|
|
Kangaroo Creek - Savannah Way east of Borroloola118 views
|
|
5 views
|
|
5 views
|
|
Interior shot with walnut finish57 views
|
|
STALWART CAB93 views
|
|
Thread upload4 viewsImage uploaded in thread 179206
|
|
73 views
|
|
wading185 views
|
|
60 viewsColdweathers, classic 90 blew up its expansion bottle, he was glad of the ride to the top but funnily enuf didnt want a tow to the bottom, some say it may have been due to the fact that his 90 looked like it had been taken jet sking on the back of a D3
|
|
4x4 Reliability Comparison - 201127 viewsTaken from Warranty direct survey / reliability index.
|
|
4x4 Info on MY0542 viewsPicture taken of 4x4 info screen on my 2005HSE with no known software updates done.
|
|
wax57 views2
|
|
Wipers, Front and Rear, plus Washers description and operation.818 viewsThis 17 page pdf describes how the wipers, front and rear, plus the washers are intended to operate. Also described is how the rain sensor is designed to function along with a table of the wiper delay timing parameters.
|
|
6 Way Fuse Box9 views
|
|
Wadi Rai, a slow climb19 views
|
|
16 views
|
|
Even in Oman they have water splashes!104 viewsThe sheer joy of driving through fresh water in a mountain wadi. Rare enough to find running water when it isn\'t raining, but to drive through too is a real bonus for us Middle Eastern ex-pat drivers!
|
|
Shade is a rare commodity88 viewsRunning through the wadis approaching Jebel Achter, shade is a commodity scarce enough not to waste.
|
|
the Matzker wheel spacer - nicely machined. people warn about wheel bearings.375 views
|
|
Big Red awaits86 views
|
|
wax188 viewsWaxmaster pictures
|
|
Day 7 walks17 views
|
|
Thread upload0 viewsImage uploaded in new thread
|
|
6mm Heat Shrink colours 362 viewsI decided to colour code the tubing so I used 6mm electrical heat shrink.
As there is no apparent colour coding re the 3, I tried to emulate the P38 coding; #1 LR red, #2 RR blue, #3 LF yellow, and #4 RF green. This was not doable as both left side air springs have green coloured tubing coming off the top of the front and rear air springs. I therefore arbitrarily chose the Left Rear to be red; Left Front green; Right Front yellow; Right Rear blue; and for the air compressor supply line, White coloured heat shrink. Since two new lines tie into each air spring line, I made the line between the air spring and the FASKIT, a single solid colour, and the line from the FASKIT to the valve block, White, plus the related appropriate solid colour.
|
|
6mm PA12 grade nylon tubing with heat shrink applied 544 viewsShows some of the 6mm air line with heat shrink applied to one end of tubing. Shrink will be applied to the other end once field cut to length. These four tubes, each about 20 ft (6m) long, feed to the rear. Re the front air lines, (not shown), four additional lengths, each about 10 ft (3m) long, are required plus one more 3 metre length for compressor air. The 6mm tubing is a Nylon product specified as PA12. There is also a very similar Transport grade PA11 material, however it seems that PA12 is the more common Transport grade now in use. Also the applicable DIN standard seems to be both DIN 73378 and DIN 74324 for the nylon tubing. The working pressure of the 6mm tubing is about 27 Bar and bursting 82 Bar @ 20C. This is for the 1mm nominal wall thickness material, (4mm ID, 6mm OD).
|
|
Navi Becker and iPod286 viewsThe Becker Highspeed II was installed in the bin with power connected. Works great, even TMC worked inside the garage right away!
|
|
Thread upload5 viewsImage uploaded in new thread
|
|
Replica AC Cobra 4276 viewsSelf design & build cobra 427 in a small house garage over a 4 year period. 515bhp & 3mpg if you push hard with the right foot. Track days were the most fun I've had with clothes on. Sadly she's gone to make way for the more sedate "E" type.
|
|
Star Wars Spoiler17 views
|
|
Land Rover298 viewsjust been cleaned hard work lol
|
|
My Disco 3380 viewsThe Disco 3 the dayI got her
|
|
Thread upload2 viewsImage uploaded in thread 180038
|
|
Husky Organizer Bags123 viewsUse these or something similar if you own a refrigerator cubby box and want to use it for storage and occasional fridge. They go for under $7.00 at Home Depot.
|
|
When it was new72 viewsLothian 4x4 Response off-road day at Bathgate July 2010
|
|
Yarwell Shallow Water76 views
|
|
82 views
|
|
High Tilberthwaite40 views
|
|
UHF CB374 viewsGME TX3400 UHF CB remote head mounted on the front of the ashtray.
A piece of wood was turned to fit the cup holder to mount the GPS
|
|
UHF CB439 viewsThe remote head of the GME TX3400 was mounted on the front of the ashtray after unclipping the ashtray facia. The head is very light, double sided tape was used plus 1 screw to hold it.
|
|
A380 leaving Brisbane191 viewsOn its way to Sydney and to drum up some business for the Airbus people.
|
|
A380160 viewsQANTAS staff pose with the very large A380 whilst it was in Brisbane having some promotional logos attached.
|
|
Ham Radio448 viewsThe remote head of an Icom IC706 was mounted on a piece of wood shaped to fit into the coin holder. This is quite a tight fit and does not shake loose. The radio is mounted under the driver seat.
|
|
Antenna Bracket388 viewsThis was bent from a piece of 3mm x 25mm alloy flat bar. I used automotive grade double sided tape and two screws to fasten it. I have a dual band VHF/UHF antenna on this bracket
|
|
View from verandah towards Norther Ireland173 views
|
|
View from verandah towards Isle of Man200 views
|
|
In the water splash191 views
|
|
Ace_Narpy1219 viewsThe Narpy mod begins
|
|
Moi - as seen on Crimewatch399 views
|
|
View across the plain113 viewsThis was a shot across the plain taken with my KM Z5 at maximum 12x optical resolution - these vehicles were a long long long way away!
|
|
314 views
|
|
Add A Circuit Littelfuse Data sheet2278 viewsThe switch connects to what Littelfuse brand calls an Add-A-Circuit model FMH200BP which is an adapter that plugs in place of a Mini fuse and then has space for two Mini fuses, (original and a second one). In this install, only the original 5 amp fuse was used - adapter was so as to route power from fuse box thru fuse, then rocker switch, and then back to fuse box.
Before you install the Add A Circuit for this application, take an ohm meter and trace out the circuit path of the four slots that fuses could insert into. The path is more complicated than one might first think. As such, the orientation of the fuse holder in the socket matters for this application - that is for a circuit diverter, rather than accessory adder.
|
|
D2 in Wadi Bih86 views
|
|
Land Rover Aerial Fin images for both Glass and Metal Roof Disco3 / LR3863 viewsAs well as the two different fins, this pdf also shows the plastic blanking plate for glass roof vehicles where no fin is installed.
The glass roof fin is secured by two security screws from the top into a plastic frangible glue on gasket. The hope is that when struck, the fin will shear off and not crack the glass roof. Re the metal roof design, the fin is secured from underneath via two nuts.
The pdf also shows the various electrical bits related to the antennas. In the UK, the fin would house not only a cell phone antenna but the TV and satellite radio antenna electronics as well; in the States, the Sirius sat radio antenna and a G type cell phone antenna if the phone kit was installed would reside within the fin. The SAT NAV GPS antenna is located within the High Mount Brake Light plastic mounted to the upper rear hatch.
|
|
14 viewsOur treasure, passed away in june'12
He served for 14 years.
We miss him.
|
|
water tank83 views
|
|
Freshly Washed68 views
|
|
Got Released and on my way again!443 views
|
|
Air Conditioner Drain Hose on Drivers Side (LHD)2296 viewsThe corrugated rubber bit above and to the right of the gas pedal is the drain hose that goes down thru the carpet and floor sheet metal.
While it is bit hard to figure out from the jpg above, there is a rubber "strap" attached to the top of the corrugated hose that one uses to pull on to drag the hose up back around the black plastic heater "pan" drain. The same drain hose arrangement is on the other side as well.
One could I suppose run a plastic snap tie around the vertical pull strap if one was concerned about the hose slipping off again. See also the other jpg sketch which is from the Land Rover manual.
|
|
Air Conditioning Pipes (File 1)983 viewsIt\'s the smaller of the 2 pipes that is leaking. Both pipes are encased full length in the foam sleeve. You can see where the support bracket has \'crushed\' the sleeve. The bracket is what holed the small pipe. There is a bracket at each end and one in the middle. You need to remove the suspension reservoir to get to the centre bracket. Be aware that the bolts securing the brackets may be corroded and are likely to shear off on removal!
|
|
fitted ..tucked away 155 views
|
|
Thread upload2 viewsImage uploaded in thread 178588
|
|
Lady Anne Clifford’s Way, Mallerstang106 views
|
|
The Water Cut Mallerstang104 views
|
|
60 viewsOne bolt is visible at the front, but the other two are down the left hand side and best accessed by removing the small plastic guard behind the bumper. I also removed the small metal radiator guard between the bumper and the main sump guard (but that was mostly to retrieve the spanner I dropped!). The only issue with removing the plastic guard is the stupid plastic clips that hold it on may need to be replaced.
|
|
Alternator female plug looking down into top373 viewsThis shows the plug connected to the alternator wiring harness looking down into the top of the plug.
The cavity marked 1 is the AS or BATT SENSE and the wire colour most likely has Brown/Green on it.
The cavity marked 2 is the RC or ALT CON and the wire colour most likely has Red/White on it.
The cavity marked 3 is the L1 or ALT MON and the wire colour likely has Green/White on it.
I say "most likely" as the wire colours are not always the same on all vehicles.
Also the terminal 1 conductor destination is more likely C0570-175 rather than per the jpg.
The #3 pin is located closest to the big B+ terminal.
|
|
Thread upload4 viewsImage uploaded in thread 183933
|
|
February in the sun!186 viewsNo D3 to drive but the weather and location was excellent!!
|
|
Amp Drawing53 viewsThis is how many amps my vehicle was using when the ign in possision II. Lights where off, radio off,hvac off Crazy?
|
|
176 viewsThis photo was "Autostitched" from 7 individual ones.
|
|
CAD render of a rim I created.71 viewsCAD render of a rim I created. Was supposed to look like the 18" style 2 rims.
|
|
Thread upload10 viewsImage uploaded in thread 152982
|
|
Thread upload18 viewsImage uploaded in new thread
|
|
Cam mounted on sun-visor244 viewsI usually place something in between the sun-visor and the roof lining to give the cam a better angle. At Boughrood it was a roll of PVC tape. For Boughrood I also placed a small cardboard box between the cam and the sun-visor to bring the cam away from the dirty section of windscreen.
|
|
Crossing the Arctic Circle. October 201034 viewsHeading North
|
|
Thread upload3 viewsImage uploaded in thread 186251
|
|
Thread upload7 viewsImage uploaded in thread 197745
|
|
Astra 1.6 fuel consumption29 viewsFuel consumption of a 1.6 petrol Astra after a return trip from Aberdeen to Peterhead.
And yes I know i am sad listening to radio 2, but it was the only station I could understand up there.
|
|
Astute Cutaway252 views
|
|
168 viewsAfter a nice day out with lot of fun at Avon Dasset Quarry.
|
|
155 views
|
|
Studded AT2\'s. 5 new waiting in garage, and one additional spare already used two seasons.52 views
|
|
Hippo Dwarf181 views
|
|
Nav System Error Message20 viewsThis is the error I got onscreen after trying satnav upgrade from a dodgy copy. Same error then using old disc. Solution was to use a 'good' copy or the same type as the duff upgrade disc.
This isn't a duff photo - the screen really does have a double image of the text.
|
|
Riparazione attuatore rotante volante - Steering rotary coupling repairing22 viewsCome riparare l'attuatore rotante del volante quando si accende la spia dell'airbag.
How to repair the steering rotary coupling when airbag warning light turns on.
|
|
Our Trip Apr-Aug 2008135 viewsGosford to: Broken Hill, Innamincka, Birdsville, Alice Springs, Bungle Bungle NP, Broome, Gibb River Rd to Mitchell Falls and then Kunnunurra, Darwin (for tail gate Repair), Normanton (via Roper Bar, Borroloola, Lawn Hill, Burketown), Townsville, down coast to Noosa then inland to home. TRACK TRACE BY TRACKRANGER SOFTWARE ON ASUS UMPC.
|
|
-21 deg and doing my bit for global warming.......... dont think the tree hugging Toyota next to me was too impressed193 views
|
|
Aux Battery showing ground cable bolt "upside" down 1577 viewsIn order to obtain sufficient height clearance to get the plastic cover back on, I had to install the ground cable to the underside of the battery post connector.
Note the battery vent hose, (approx 5 ft required) is run down into where the windshield washer fluid container is located. There is not much electrical or metal in that area to be corroded by battery gas plus the open end of the vent hose tends to be protected from dirt and stays clean as well.
|
|
BCI Group 40R Deka 640RMF battery showing vent hose run forward to windshield washer reservoir area 1430 viewsRecessed post "Euro profile" battery to "match" OEM and stock Land Rover bracket; note that the Traxide SC80-LR module is mounted at an angle to allow for the main cable to sit under the cover so cover still closes.
The battery is a nominal 7", (180mm), high, but sits on a 1" battery spacer set under to raise the bottom front end of the battery such that the approx 11", (290 mm), length of the BCI 40R battery rises above the angled plastic nibs at the forward end bottom of the case front; hence sufficient space, (1/4", 5mm) remains at the brake reservoir end.
Also the 40R battery does not have hold down "flanges" on each end; on the sides yes, but not the ends so no additional length is required.
When I had to replace the 40R, this time I installed the shorter, (9.625"), taller, (7.5") Interstate BCI 47 / DIN H5 battery which eliminated the spacer on the bottom and better fit the stock LR tie down bolt lengths. Deka also has a BCI 47 / DIN H5 that would work fine as well.
|
|
198 views
|
|
Thread upload5 viewsImage uploaded in thread 142922
|
|
30 views
|
|
148 views
|
|
A320 USAirway81 views
|
|
A Pillar Black Plastic cover install pdf - new type.1038 viewsThis 3 page LR pdf explains how to install the newer A pillar plastic covers and avoid instant water leakage as a result of the new design.
|
|
Bad Rock61 viewsbenign looking rock that punctured the sidewall of my new General Grabber AT2 (500km done on tyre)
|
|
got one shot on 4x5 transparency film. then it was gone.143 views
|
|
Bald Seet village164 viewsDescendign a steep concrete track over gravel into the villaeg of Ballad Seet. Curious in a dry, desert country to find verdent growth of palms, and agricultural produce on well watered terraces.
|
|
106 viewsHWY 150, colloquially known as Mirror Lake Highway.
|
|
Thread upload9 viewsImage uploaded in thread 136164
|
|
BAS remap interface after dealer software update287 viewsBAS remap interface after dealer software update,This is what you will be presented with after the dealer updates your cars engine software.
This is no problem IF you have returned the car to standard before the dealer visit.
When faced with this screen it will show you tht the dealer has changed the software and NOT let you put the BAS mapping back on your car because of the differences.
|
|
Caterpillar Battery Size cross reference chart and battery profiles including post layout752 viewsThis pdf has a dimension, (metric and inches), cross reference chart plus another sheet that provides BCI and DIN cross reference numbers and shows post locations plus bottom ridge tie down locations, (or the lack of).
This data was for me, hard to find, and helps one in selecting a suitable physical size of Aux battery for the space available.
|
|
Battery Disconnect side post with + & - caps, top view617 viewsThis disconnect is designed for side post batteries. It can be used on either the + or - terminals. It can also be installed at the "other" end of the battery cable as well. In my install of the Aux battery, I installed this on the negative ground cable where the cable attaches to the body sheet metal. I have never used it but it seemed like a good idea at the time. The main battery hookup is pure stock.
For the hot side of the Aux battery, an Anderson PowerPole was used inline for the cable between the Aux and connecting to the spare bolt hole at the + post of the Main battery cable.
|
|
Woodlands Hotel6 viewsGreen Oval Garage would like to say thank you to the Woodlands Hotel in Leeds for allowing us the use of their beautiful grounds for all our future photos shoots.
Woodlands is one of the finest luxury hotels in Leeds. This boutique hotel is set in beautiful landscaped grounds on the outskirts of Leeds city centre, just 2 minutes drive from junction 27 of the M62 motorway, with 23 individually designed bedrooms and an award winning restaurant. Packed with character, this lovingly restored hotel is only three miles from the vibrant, cosmopolitan city of Leeds with superb nightlife and unrivalled shopping.
Woodlands also offers a stylish and contemporary functions venue for all kinds of social and business events. Our three stunning event spaces are suitable for everything from wedding ceremonies and receptions, to corporate meetings and events. The permanent marquee, attached to the hotel, can accommodate up to 150 for dining and 200 for evening parties and receptions, making it one of the most elegant settings for a wedding venue in the Leeds area.
For more information or to make a booking, please contact us on enquire@woodlandsleeds.com or 0113 2381 488
|
|
Thread upload17 viewsImage uploaded in new thread
|
|
Thread upload6 viewsImage uploaded in thread 141621
|
|
Thread upload11 viewsImage uploaded in new thread
|
|
2008 Calendar Entry - D3 go mad in Cornwall670 viewsMy D3 just above Pendower beach on the Roseland Peninsula in Cornwall in August 2007. Wife and kids are out of shot.... standing in the road to prevent other cars parking!!
|
|
Always start with removing the dog from the engine compartment55 views
|
|
Bent Black Betty228 viewshard to believe that in this condition she\'s a write off, what got her was the cost of tricknology repairs, seatbelt pretensioners, airbags etc etc, & declining values, repair estimates €12500, value €13000. a no brainer really
Note TASTEFULL G4 sticker
|
|
Thread upload20 viewsImage uploaded in thread 116743
|
|
Calendar 2010355 viewsSolway Coast July 09
|
|
Calendar 2010341 viewsSolway Coast July 09
|
|
Calendar 2010353 viewsSolway coast July 09
|
|
32 views
|
|
Swan Neck15 views
|
|
Big Brother is watching30 views
|
|
Big Fishes271 viewsThe gradual metamorphosis begins. Sad to be gettinng rid of the 110, but looking forward to abusing the Disco.
|
|
Coolant hose between water circulating pump and FBH46 views
|
|
Thread upload15 viewsImage uploaded in thread 148535
|
|
Bin Cover removed showing forward release clips that clip into the two rectangular slots.10 viewsOne has to pull up on the Bin Cover to unlatch the two metal clips, hence why release of the C pillar cover makes the bin cover removal and reinstall easier.
|
|
White plastic pin that has to be partly removed to assist in release of buzzer cover.11 viewsThe white coloured plastic pin is located near the C pillar and has to be partly pulled out to release the black plastic buzzer cover.
|
|
23 viewswhist we was looking round glossop caravans.
|
|
One of the trails at George Washington National Forest - Harrisonburg, VA139 views
|
|
Blue Ridge Parkway, North Carolina, USA186 views
|
|
Smart Roadster Bluewave187 views
|
|
150 views
|
|
135 views
|
|
3339 files on 9 page(s) |
|
1 | |
|
|
|
|
|
|
|
|