| Search results - "Sheet" |
0000 LR Bluetooth dealer Kit install instructions1608 viewsThis 17 page pdf is mostly a series of pictures showing how to install the original Land Rover dealer installed Bluetooth kit for circa 2005 / 2006 three's. Also included are three wiring diagrams sheets related to the pairing code 0000 Bluetooth install.
This pdf is useful if you are now removing the 0000 kit to install the optical 2121 MOST D4 module, an easier install than the 0000 kit ever was.
|
|
12 Half way through removing a jammed disk brake in the Outback296 viewsThis was just before breaking the sledge hammer. Note we luckily carried a spare hammer. Ended up using (or breaking) every tool we had on this little repair job. Bed sheets are a good way of gathering the bits to show for the inevitable warranty claim.
|
|
2010 Discovery 4 Data Sheet (all engines)1254 views
|
|
8 views
|
|
Add A Circuit Littelfuse Data sheet2278 viewsThe switch connects to what Littelfuse brand calls an Add-A-Circuit model FMH200BP which is an adapter that plugs in place of a Mini fuse and then has space for two Mini fuses, (original and a second one). In this install, only the original 5 amp fuse was used - adapter was so as to route power from fuse box thru fuse, then rocker switch, and then back to fuse box.
Before you install the Add A Circuit for this application, take an ohm meter and trace out the circuit path of the four slots that fuses could insert into. The path is more complicated than one might first think. As such, the orientation of the fuse holder in the socket matters for this application - that is for a circuit diverter, rather than accessory adder.
|
|
Air Conditioner Drain Hose on Drivers Side (LHD)2295 viewsThe corrugated rubber bit above and to the right of the gas pedal is the drain hose that goes down thru the carpet and floor sheet metal.
While it is bit hard to figure out from the jpg above, there is a rubber "strap" attached to the top of the corrugated hose that one uses to pull on to drag the hose up back around the black plastic heater "pan" drain. The same drain hose arrangement is on the other side as well.
One could I suppose run a plastic snap tie around the vertical pull strap if one was concerned about the hose slipping off again. See also the other jpg sketch which is from the Land Rover manual.
|
|
Caterpillar Battery Size cross reference chart and battery profiles including post layout752 viewsThis pdf has a dimension, (metric and inches), cross reference chart plus another sheet that provides BCI and DIN cross reference numbers and shows post locations plus bottom ridge tie down locations, (or the lack of).
This data was for me, hard to find, and helps one in selecting a suitable physical size of Aux battery for the space available.
|
|
Battery Disconnect side post with + & - caps, top view617 viewsThis disconnect is designed for side post batteries. It can be used on either the + or - terminals. It can also be installed at the "other" end of the battery cable as well. In my install of the Aux battery, I installed this on the negative ground cable where the cable attaches to the body sheet metal. I have never used it but it seemed like a good idea at the time. The main battery hookup is pure stock.
For the hot side of the Aux battery, an Anderson PowerPole was used inline for the cable between the Aux and connecting to the spare bolt hole at the + post of the Main battery cable.
|
|
55 views
|
|
73 viewsMS excel sheet for monthly mileage report will give average fuel consumption.(most cells have formulas to help fill in from previous line)
on first sheet add details you want on monthly sheets. during use the data needed to be added is ending reading on clock, places visited (if you want).
how much fuel when you purchased it also fuel in tank at start and end of month
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload4 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload2 viewsImage uploaded in thread 207991
|
|
Thread upload1 viewsImage uploaded in thread 207991
|
|
Thread upload1 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
Thread upload0 viewsImage uploaded in thread 207991
|
|
15 views
|
|
Thread upload7 viewsImage uploaded in thread 165001
|
|
76 views
|
|
Maintenance Check Sheet Arduous 3.0 TDV6 Models to 11MY Discovery 4 / LR423 viewsMaintenance Check Sheet Arduous 3.0 TDV6 Models to 11MY Discovery 4 / LR4
|
|
Maintenance Check Sheet Rest of World 3.0 TDV6 Models to 11MY Discovery 4 / LR417 viewsMaintenance Check Sheet Rest of World 3.0 TDV6 Models to 11MY Discovery 4 / LR4
|
|
Maintenance Check Sheet All Models UK & EU to 11MY Discovery 4 / LR412 viewsMaintenance Check Sheet All Models UK & EU to 11MY Discovery 4 / LR4
|
|
Maintenance Check Sheet All Models UK & EU Discovery 415 viewsMaintenance Check Sheet All Models UK & EU Discovery 4
|
|
D3 Maintenance Schedule - Kilometre version130 views
|
|
169 views
|
|
Italian Maintenance Check Sheet251 viewsLRE008ITA (2)
DISCOVERY 3 SCHEDA DI CONTROLLO MANUTENZIONE (TUTTI I MODELLI INGHILTERRA & EUROPA)
|
|
Italian Maintenance Check Sheet228 viewsLRE011ITA (2)
DISCOVERY 3 SCHEDA DI CONTROLLO MANUTENZIONE (TUTTI I MODELLI PER CONDIZIONI GRAVOSE)
|
|
Italian Maintenance Check Sheet137 viewsJLR 11 81 14_7E (7)
DISCOVERY 3 SCHEDA DI CONTROLLO MANUTENZIONE (TUTTI I MODELLI RESTO DEL MONDO)
|
|
service182 views
|
|
Disco3 Maintenance Checklist26 views
|
|
Thread upload27 viewsImage uploaded in thread 132681
|
|
Maintenance check list281 views
|
|
Disco 3 - Suspension Leveling & drop check worksheet32 viewsUsed to work out how much your disco drops on its suspension and if its outside of the standard tolerances.
If you have any suggestions on how it can be improved please let me know.
|
|
Close-up front view of partially-installed winch120 viewsNote that the sheet-metal flange just above the winch had to be notched to allow winch controller to be actuated. Also this same bracket had to be bent upwards to allow the winch hydraulic:electic solenoid to fit without rubbing. The nut on the upper-left bolt (the one with a very faint circle around it) stripped on re-installation, so the tray and winch pulling load is held only by the threads on 7 bolts....
|
|
Photo showing inside sock.166 viewsThere is a double layer inside. Just like a conventional tent, the waterproof layer, then a flysheet. Both can be zipped/unzipped when vehicle is not in place.
|
|
Fitted "echo" drawers in one of the front doors. an almost perfect fit, just a little sheetmetal work needed. the cho guys would probably vomit if they saw this107 views
|
|
Exploded Parts view calling up 6R60/80 and 6HP26/28 variations3113 viewsThis single page jpg exploded parts view indicates some commonality between the Ford and ZF versions of the early and later six speed units. Technically this sheet is for the RWD units as there are variations between plain RWD units, 4WD, and AWD. The transmission in the LR3 is called by ZF to be a 6HP26X and by LR in some publications, the 6HP26
|
|
MS Excel chart of fuel usage in TDV6 first 3 months of ownership201 viewsReason for distortion at beginning is not known - average so far is 11.55l/100k (25.09mpg) for the 6 199k travelled. The fuel usage 'bumps' correspond with the city driving although they did mirror the cost for a while! A copy of the spreadsheet (105kb) that shows MPG and l/100k (but not miles) is available for the asking - just PM me.
|
|
Gore Tex data sheet on Breather Cap.784 viewsThis is a Gore data sheet on the air vent material that is within the breather cap. The filter material has both hydrophobic and oleophobic properties. That means it keeps water out and the differential oil in.
Also the membrane material is air permeable; that means air pressure is equalized between the interior of the differential and outside air. This is important when the 3 is flying at altitude in the back of a Hercules with the rear door open - that is the rear hatch of the Herc.
|
|
Dunnet Head Info Sheet138 views
|
|
IID-EAS Calibration spread sheet235 views
|
|
IIDTool EAS Calibration Excel86 viewsThis is the spreadsheet I made using Numbers 3.1 on a Mac, exported as an Excel file.
I haven't tried it on anything other than Numbers though.
|
|
Calibration Spreadsheet for Mac Numbers48 viewsThis is the spreadsheet I made using Numbers 3.1 on a Mac
|
|
Post Suspension Calibration56 viewsA spreadsheet I made showing results of suspension calibration using Gap Diagnostics IIDTool
|
|
Pre Suspension Calibration58 viewsA spreadsheet I made showing results of suspension calibration using Gap Diagnostics IIDTool.
This is the pre-existing values
|
|
Underside of the ciruit board127 viewsThis looks more of a mess than needed to be. The Maplins guy tried to be helpful when I bought the relays, he wrote down the switching COM/NO/NC, it was actually NC/COM/NO. Some scratching of head when it didn't work then worked out what happened when I looked on the manufacturers website at the data sheet...lesson of the day check the data sheet!
|
|
Picking sheet in MSV2 box25 views
|
|
Step drill131 viewsCan drill from 4 - 22 mm in steps, all plastics and sheet metal.
|
|
Interstate Battery Dimension sheet640 viewsThis sheet is hard to find - the sheet is not on the Interstate corporate web site but some dealer web sites display it. The pdf shows most of their available batteries including the H7 and H8 sizes that are the LR North America replacement batteries for the main starting battery. These batteries are of the Land Rover desired "shallow" cycle high discharge current Maintenance Free, (Ca Ca), internal construction, (not AGM, but instead, Wet Flooded Lead Acid with battery "caps" and Ca grid separators).
For the AUX battery , the H6, (BCI Group 48), is probably similar in dimensions to the Varta E12V75N that is popular in Australia. For that battery to fit in the second battery compartment, you must grind out the angled nibs on the inside front bottom of the LR black plastic surround, something I did wish to do and hence installed a Group 40R on a spacer. Alternately, one can choose an Interstate BCI Group 47 which is similar to a DIN H5 for the AUX location. I did this when I had to replace my 40R. No vertical spacer is required and the stock battery tie down bolts and clamp work well.
|
|
Discovery 3 Maintenance Check Sheet (All Models Rest of World) - miles182 viewsDiscovery 3 Maintenance Check Sheet (All Models Rest of World) - miles
JLR 11 81 10_7E
|
|
Discovery 3 Maintenance Check Sheet (All Models UK & EU) - miles214 viewsDiscovery 3 Maintenance Check Sheet (All Models UK & EU) - miles
JLR 11 82 10_6E
|
|
Discovery 3 Maintenance Check Sheet (All Models Arduous) - miles154 viewsDiscovery 3 Maintenance Check Sheet (All Models Arduous) - miles
JLR 12 05 10_6E
|
|
L319_Discovery_4_MY2010-2011EU_Maintenance_Check_Sheet_-_all_Models_-_km34 views L319_Discovery_4_MY2010-2011EU_Maintenance_Check_Sheet_-_all_Models_-_km
|
|
Littelfuse Add-A-Circuit MINI and ATO style data sheet150 viewsPDF from Littelfuse showing both the MINI and ATO style of fuse holders. The 3 uses the MINI size of fuse. The MINI Add-A-Circuit can be inserted in place of one of the existing fuse panel MINI fuses. The removed fuse is then inserted into the lower slot of the Add-A-Circuit and a second fuse in the second slot to protect the device that you are adding. The Add-A-Circuit is designed for a max of 10 amps on the second load, and I guess maybe the original circuit as well.
|
|
LLumar "windscreen" clear Infra Red reduction side window film929 viewsThis is a data sheet on the LLumar brand of what they call Windscreen Film; It is almost clear, (has a bit of a blue tint), and reduces both the Ultra Violet fading and sun burn rays which most all films do as that is easy, plus more significantly, the Infra Red heat rays. That is rare as it is not so easy or cheap to do.
AIR80BLSRHPR (blue) is what the IR rejection film is listed as in the brochure that I used. http://www.llumar.com/en/AutoWindscreen.aspx
I had it applied to the front side windows as well as the front sun roof. One can feel the difference when the sun is low and streaming thru the side glass or high and coming thru the sun roof. Rolling a side window down is the simplest test of effectiveness re the rejection of the heat energy.
|
|
Power Window Circuit Sheet 2 Central Junction Box to Passenger Front Switch365 views
|
|
Power Window Circuit Sheet 3 Central Junction Box to Rear Switches391 views
|
|
Power Window Circuit Sheet 1 from Battery to Central Junction Box (fuse box behind glove box)352 views
|
|
Air Suspension Wiring Sheets3037 viewsThese two sheets show the wiring and fuses related to the operation of the air suspension system. Fuses F3E, F26E, and F35P are shown as well as the interior up down switch and the wheel height sensors.
As with all pdf's, you can rotate them to view plus download and or print out as you wish.
|
|
Excel file for Rotors and Brake Pads part numbers for 4.4L V8 petrol LR3768 viewsComparing the cost of the various brands of brake parts is time consuming. Once you have your parts costs, this little spreadsheet will make collating the info easier.
I did not make any provision for labour costs, but the file can be downloaded and then modified. You can change Dollars to Euros or Pounds or whatever and insert lines for labour costs as desired.
Do not pay too much attention to the $ numbers as they are a mix of US and CDN, and from differing time frames, (prior to Spring 2011) . Also the brake part numbers are for my 2005 North America spec LR3 with the petrol 4.4L V8; diesel powered and supercharged 3's may have different part numbers
|
|
Power Door Lock wiring diagrams530 viewsI thought I would include this 5 page power door lock wiring diagram pdf here as well.
When the pdf loads, if the views are vertical, it may be that you can right click on your mouse and a box will come up that will allow you to rotate the views clockwise so that the sheets are horizontal. Alternatively you can download the file and print each sheet yourself.
|
|
ZF 6HP26 Land Rover Transmission specs1677 viewsThis is just two sheets of paper with various numbers related to the 6HP26 such as oil capacity, gear ratios, and torque wrench settings for the fill and drain plugs.
You may note that LR calls this ZF transmission the 6HP26 whereas ZF calls out the LR3 transmission as the 6HP26X. Just what the differences are, I am not certain however the X refers to 4WD or AWD use as opposed to solely 2WD.
Zahnradfabrik is what ZF is short for and translated from German, roughly means Gear Factory.
|
|
D4 non-3L arduous maintenance checklist28 views
|
|
Maintenance Check Sheet Non 3.0 TDV6 Models To 11MY Arduous Discovery 4 / LR412 viewsMaintenance Check Sheet Non 3.0 TDV6 Models To 11MY Arduous Discovery 4 / LR4
|
|
Maintenance Check Sheet Non 3.0 TDV6 Models To 11MY Rest Of World Discovery 4 / LR417 viewsMaintenance Check Sheet Non 3.0 TDV6 Models To 11MY Rest Of World Discovery 4 / LR4
|
|
D4 non-3L maintenance checklist (rest of world)29 views
|
|
Maintenance Check Sheet65 viewsMaintenance Check Sheet
|
|
Maintanance Disco 357 views
|
|
1 sheet service record insert35 views
|
|
4 sheet service record insert36 views
|
|
Lug Nut part number RRD500290 outline sketch541 viewsThis single sheet pdf provides dimensions of the LR part number RRD500290 lug nut on vehicles from MY 2005 to 2008, (up to VIN 8A450459). From VIN 8A450460, the part number is RRD500590.
Visually, there is no apparent difference between the two part numbers. The dimensions appear identical as well. The shape, size, and profile of the Stainless Steel "hat" appears identical.
There are I presume differences in metallurgy to reduce corrosion and swelling of the hat or perhaps better sealing between the inside surface of the hat and the steel of the lug nut body. The reality is the differences are not immediately obvious however.
A 22 mm six point half inch or larger socket drive fits over the lug nuts. I use a nominal 36" long breaker bar with the 22mm socket - any shorter bar, best you be in shape. Depending upon your source, for both alloy and steel wheels, the lug nut torque value appears to be 103 lbf ft, (140 Nm); others suggest first tighten to 96 and then finish at 110 lbf ft, (130 and 150 Nm).
|
|
PDF of Mini Fuse data re LR3 / Disco 3 fuses.1854 viewsThis is just a data sheet regarding the MINI fuses that are common in the 3.
|
|
Spreadsheet to calculate MPG23 views
|
|
Maintenance Check Sheet213 views
|
|
Sheet ice at a car park in the Lakes on New Years Day 0951 views
|
|
Pattern for Expo Roof Rack Floor Sheet397 viewsI used a 3mm sheet of Aluminium - with 150mm wide Grip Tape to do the Chevron Patter to make it a bit safer. Note the sheet is 1610mm long, 1100mm wide at the front and 1060mm wide at the back. I drilled 3 rows of 5x 12mm holes - one row down the centre and one either side 30mm in from the edge. The hole centres being at 31mm from the front edge, next 420mm from 1st hole centre, the 375mm from 2nd hole, 372mm from 3rd hole, 375mm from 4th hole, leave 31mm to the back edge. Edited May 2008: I've subsequently cut the sheet in half lengthways to make removal and fitting easier as I found the sheet increasing noise and reduces MPG considerably.
|
|
Optima Battery781 viewsBattery makers sheet for all you rivet counters out there.
|
|
Italian Maintenance Check Sheet134 viewsJLR 11 82 14_6E (6)
SCHEDA DI MANUTENZIONE (TUTTI I MODELLI REGNO UNITO ED EUROPA)
|
|
Italian Maintenance Check Sheet144 viewsJLR 12 05 14_6E (6)
SCHEDA DI MANUTENZIONE
|
|
7 views
|
|
Racor filter spec sheet188 views
|
|
Racor filter spec sheet 2224 views
|
|
70 views
|
|
71 views
|
|
57 views
|
|
ZF 6HP26 Metal Pans, (top and bottom views), and separate Filter top and bottom views.1765 viewsThis single sheet pdf two views of the ZF metal pan for the 6HP26 transmission. The inside view shows the two magnets; the other is the bottom view. Also visible are the transmission bottom oil fill and oil drain holes that are sometimes utilized where access to the side fill is not possible. The ZF part number for the metal pan kit for our 6HP26X six speed is 1068_103_820_01 This includes the 21 shorter Torx screws, the metal pan gasket, and the separate oil filter as well as round filter seal. The ZF six speed LifeGuard6 transmission oil is extra.
|
|
|
|
|
