Member Since: 03 Oct 2018
Location: Kent
Posts: 620
V8 petrol possible fuel leak and or fuel pump or connector
I'm pretty sure I know the answer but just wanted to check with the collective.
Recently had intermittent crank no start on the V8 no codes with the gap tool have so far replaced the cps just to be sure and am now getting ready to drop the fuel tank.
Iv checked for fuel pressure at the shader valve and iv a healthy jet of fuel comming out.......soooo there has always been a bit of petrol smell sometimes from the rear I'm aware the fuel pump cover plate fails and the sealing ring so there on order plus the electrical connector that burns out and for good measure a fuel pump.
Question is.....is there an inspection plate from inside the car under the rear carpets ??? before I go pulling this lot out .
I know to change them iv got to drop the tank regardless iv done a few lpfp on tdv6s but for the life of me can't remember if there is an inspection plate .
11th Mar 2024 12:16 pm
PROFSR G
Member Since: 06 Mar 2017
Location: Lost
Posts: 5068
No inspection plate, you have to drop the tank. yµ (idµ - eAµ) ψ=mψ
11th Mar 2024 2:26 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Yeah I was pretty sure that was the case iv been spoilt working on fullfats and late sports
11th Mar 2024 2:31 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Or nothing at all I refer to previous posts iv found and wonder if I'm suffering the same issue.
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Well parked it facing up the drive and still getting a long crank no start or long crank then start or normal crank then starts.
Will try and magiver something to allow me to connect this next to unless fuel pressure testing kit to the car and see what's going on.
15th Mar 2024 6:36 pm
Naki Blake
Member Since: 31 Dec 2021
Location: Taranaki
Posts: 325
Hi. I may be well off the mark, but I had an intermittent crank and no start on my V6 Petrol 4.0L. Very frustrating, either cold start, or warm start e.g supermarket car park, car warmed up but switched off for 40 mins or so while doing shopping.
Sometimes mine would crank, fire but immediately die. Or crank for say 10 seconds and then start. Or crank but not start. Would happen approx monthly.
Solution for mine was my garage replaced the EGR which has the MAP (manifold absolute pressure) sensor built into it. I had that replaced approx 2 years ago and have never had a starting issue again.
Like I say, completely different engine, but being the V6 petrol (not an option in UK), thought I would add this comment, wondering if the petrol engines share the same electronic management systems.
Cheers Blake (NZ)
Last edited by Naki Blake on 16th Mar 2024 12:58 am. Edited 1 time in total
15th Mar 2024 7:50 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Thanks, I will investigate and report back
15th Mar 2024 8:11 pm
Naki Blake
Member Since: 31 Dec 2021
Location: Taranaki
Posts: 325
As a precaution I also did the Land Rover technical bulletin LTB00335 as detailed on this forum
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Plugged the gap tool in to check live data
Ignition on only engine not running so I can take some live data at the map sensor.
Click image to enlarge
Not sure what it all means yet will have a proper look tomorrow
16th Mar 2024 12:35 am
Naki Blake
Member Since: 31 Dec 2021
Location: Taranaki
Posts: 325
Click image to enlarge
Just looking back at my old files, I would sometimes get these 2 faults when I had my crank but no start issue. I could clear these codes and they they would intermittently reappear (not a constant fault). Once EGR was replaced my engine idled more smoothly. It used to "hunt" and "surge" a bit at idle.
16th Mar 2024 1:13 am
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
I'm gonna have a good look today thing is I get no codes from gap tool so I'm checking blind. Will be keeping a look out at live data but with these intermittent faults ........
16th Mar 2024 8:23 am
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
Well I can rule out the map sensor as an issue it's working perfectly well the purple high peaks are the response to me revving the engine.....then again this was engine working.....
Click image to enlarge
But on watching the live data on a crank fail to start sequence the map sensor voltage failed to drop and stated at 2.4 volts so maybe its intermittent sensor will replace and report back
16th Mar 2024 11:33 am
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
So most likley reason the sensor voltage didn't drop on the non start sequence is because the engine wasn't running so no air pressure change to detect.
I'm gonna call the map sensor as good and iv managed to magiver the fuel pressure testing kit to the car and can report fuel pressure is good at ignition on, cranking and engine running.
Will keep looking
Click image to enlarge
16th Mar 2024 12:56 pm
Naki Blake
Member Since: 31 Dec 2021
Location: Taranaki
Posts: 325
Good to rule out MAP. Part of process of elimination. Good luck.
16th Mar 2024 6:47 pm
Lrstaylor
Member Since: 03 Oct 2018
Location: Kent
Posts: 620
I hope I'm not speaking to soon but.......I think I'm gonna call this fixed.
In the picture I posted testing fuel pressure you can see the bleed off clear tube......well I seemed to be getting a lot of air comming threw with the petrol when letting off the pressure from the gauge when I should of only had petrol.
So I turned on the ignition straight to 65 psi then released the pressure off the gauge and kept the release valve open until all the air cleared.
Car started 1st turn, I did an engine adaptation reset with the gaptool and used the fuel primer function just to be sure.
It's started 1st turn every turn of the key 10 times a day for 3 days so fingers crossed.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum