Member Since: 21 Aug 2007
Location: Wales, mun ;-)
Posts: 164
Typical - -5 degrees out and Webasto fails!
I have one of them Altox controllers to turn on the Websaso heater. It's been fine for months during quite sporadic use. I tried it a few days ago and kept getting these codes on my phone:
Error the heater does not start Technical info: W7,3,6
Webasto diagnostics code: 07,24,02
From their webside:
07 = Heating Unit Locked
24 = Car is almost out of fuel
02 = No start
I have no idea what the W7 is or whether 3 and 6 are valid codes?
Anyway, I pulled fuse 28 for a good few minutes. Replaced it and nothing. Got the same codes. Any ideas?
As a side note, I couldn't pull the fuse by hand so went to get my Leatherman from the house to use the pliers on it to lever out the fuse. When I came back I pulled out the wrong 20A fuse! It came out of either F26 or F24. Which one should it be in? F26 shows a picture of the car with an arrow pointing up so I am assuming that is the air suspension. F24 has a picture of a book and the letter "i" on it.
Yes.
I know. No need for you to tell me.
1st Mar 2018 12:31 pm
conman69
Member Since: 11 Aug 2012
Location: Norfolk
Posts: 431
Think it's fuse 28 lower one of the two 20a fuses in the outer side of the fuse box.Discovery3 TDV6 GS
Disco3.co.uk front orange +white tailgate stickers
Belts, pulleys, oil pump replaced, double tow-bar electrics
Land Rover rubber mats throughout, tinted windows, wind deflectors, smoked side repeaters, retro fitted Garmin, smooth leather steering wheel, cruise control + radio switches, 19" HSE wheels, Bearmech side-tubes, BAS IFBH module, roofbars.
LML Star Deluxe
1st Mar 2018 1:19 pm
lynalldiscovery
Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274
Going by your user name it can only be a wiring issue
1st Mar 2018 1:54 pm
Waylander11
Member Since: 21 Apr 2016
Location: Leicestershire
Posts: 521
Did you erase the codes on the appD3 in Buckingham blue now SWMBO's Mine D4 commercial
Xenon's fitted Timed climate
EGR Blanked Remapped
Remap Reversing Camera
gear box reset
updated Bluetooth
4x4 info
all done by Bodsy
Fridge fitted
Reversing camera fitted
1st Mar 2018 4:37 pm
Daf
Member Since: 21 Aug 2007
Location: Wales, mun ;-)
Posts: 164
It's at this point I realised the error of my ways.
What app?
Does this only work if I buy a cable, get the app and connect the car to a laptop? If it does then I don't have one.
What else can I try?
It's snowmageddon here.
1st Mar 2018 6:06 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
Think he means the altox app, you can download onto your mobile and control your heater as well as see the faults and clear them.
Pete.IID, webasto software and workshop facility's available.
1st Mar 2018 6:55 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
IID, webasto software and workshop facility's available.
1st Mar 2018 6:55 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
Just though that you might be texting instead of setting up a internet connection on your altox. In that case you need to pull the fuse for 2-3 mins, put it back in and wait another 2-3 mins and then text “erase” to it, then you should of cleared the fault codes.
Pete.IID, webasto software and workshop facility's available.
1st Mar 2018 7:32 pm
Daf
Member Since: 21 Aug 2007
Location: Wales, mun ;-)
Posts: 164
Many thanks for the replies. I do have the app but really haven't ventured further than hitting start!
I'll give it a go tomorrow. It's horrible outside at the moment.
Anyone have any thoughts on that other 20A fuse? Should it be in F26 or F24? My guess is F26.
1st Mar 2018 7:40 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
Is it a auto or manual? Thing the fuse below is for a auto, I’ll go check.
Pete.IID, webasto software and workshop facility's available.
1st Mar 2018 7:43 pm
zinke
Member Since: 22 Feb 2014
Location: Scunthorpe
Posts: 584
Hope you can work it out from this.
Pete.IID, webasto software and workshop facility's available.
1st Mar 2018 7:49 pm
Daf
Member Since: 21 Aug 2007
Location: Wales, mun ;-)
Posts: 164
Thanks for going to that effort Zinke.
That's how I've put them back. So the other fuse goes into F26 and there's nothing in F24.
1st Mar 2018 8:26 pm
Daf
Member Since: 21 Aug 2007
Location: Wales, mun ;-)
Posts: 164
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum